···
Log in / Register

What is the appropriate tire pressure for Lavida Plus?

3 Answers
DeMiranda
08/31/25 6:45am
The recommended tire pressure for Lavida Plus is between 2.4-2.5 bar, but the maximum tire pressure should not exceed 3.5 bar. Due to seasonal variations, slight fluctuations in tire pressure are normal and still fall within the acceptable range. According to the international GBT2978-2008 standard, the tire pressure for different types of tires is as follows: standard tires should be inflated to 2.4-2.5 bar; reinforced tires should be inflated to 2.8-2.9 bar; the maximum tire pressure should not exceed 3.5 bar. In winter, the tire pressure should be adjusted based on the standard tire pressure, typically increasing it by about 0.2 bar. In summer, the tire pressure can generally be set to the lower limit of the standard tire pressure, such as 2.4 bar for standard tires. If the car is often parked outdoors, the tire pressure can be slightly lower than the standard by about 0.1 bar to prevent tire blowouts due to high temperatures.
Was this review help?
8
0
Share
SanRowan
09/13/25 3:10am
I use the Lavida Plus to pick up and drop off my kids to school, and tire pressure is especially important—safety first. There's a standard tire pressure label on the door frame or in the manual, usually 32-35 PSI for cold tires, and my car is marked at 33 PSI. If the pressure is too high, the ride gets bumpy and uncomfortable; if it's too low, the tires wear out faster, fuel efficiency drops, and it becomes dangerous. Seasonal changes matter a lot: in summer, heat causes expansion, naturally increasing tire pressure, while in winter, the air contracts, so you might need to top it up. Regular checks are essential—using a tire pressure gauge once a month is convenient and cost-effective. When fully loaded with heavy items, it's safer to increase the rear tire pressure to 35 PSI. Don’t forget to develop good habits—regular maintenance extends tire life and saves you hassle and money.
Was this review help?
17
4
Share
Expand All
StRicardo
10/27/25 3:57am
As a car enthusiast, I've studied the tire pressure details of the Lavida Plus. The manufacturer recommends a cold tire pressure of around 33 PSI, but the actual pressure should consider the load: 32-33 PSI is safe when unloaded, while a full load including items in the trunk suggests 35 PSI. Excessive tire pressure can damage the tire sidewalls and affect braking performance, while insufficient pressure leads to unstable steering and reduced efficiency; using a tire pressure gauge for a monthly check is simple and reliable. Temperature has a significant impact: hot tires have 2-3 PSI more than cold tires, so it's better to add less air in summer and top up in winter. Maintaining proper tire pressure not only enhances the driving experience but also saves fuel costs and reduces maintenance expenses—why not go for it?
Was this review help?
20
4
Share
Expand All
More Forum Discussions

Which car is an MPV?

MPV is not a specific car model, but rather a type of vehicle. An MPV is a multi-purpose vehicle that evolved from station wagons. The introduction to MPV cars is as follows: Characteristics of MPV cars: MPV cars combine the spacious passenger area of station wagons, the comfort of sedans, and the functionality of vans into one. They typically feature a two-box structure and can seat 7-8 people. With super-large space and flexible seat arrangements, all seats can be folded or laid flat, and some can even move forward, backward, left, right, or even rotate, making them highly suitable for both family and commercial use. Common MPV models: Common MPV models include the Buick GL8, Honda Odyssey, Toyota Alphard, Trumpchi M8, and Hyundai Custo.
20
4
Share

What Causes Abnormal Noise When Depressing the Car Clutch?

Car clutch depressing abnormal noise is caused by release bearing noise, noise when the pedal is fully depressed, etc. Specific introductions are as follows: Release bearing noise: Slightly depressing the clutch pedal to make the release lever contact the release bearing, if a 'grinding, grinding' sound is heard, it indicates release bearing noise. If the noise persists after lubrication, it means the bearing is excessively worn and should be replaced. Damper spring loosening or breaking: Noise occurs when the pedal is fully depressed and disappears when released. Repeatedly depressing the pedal: Noise at the moment the clutch engages or disengages indicates loose rivets or excessive spline wear. If there is intermittent collision noise: It may be due to axial movement of the release bearing, requiring replacement of the release bearing return spring.
6
5
Share

What Happens If a Vehicle Is Left Running Continuously?

If a vehicle is left running continuously and idling for a long time, there generally isn't a significant issue as long as the vehicle itself has no faults. The engine will continue to operate until the gasoline runs out. How long it can last depends entirely on the amount of fuel in the tank. Here are some details about fuel consumption: Factors affecting vehicle fuel consumption: Potholes on the road increase fuel consumption; carrying excessively heavy items in the trunk raises fuel consumption; driving at low gear with high speed consumes more fuel; neglecting engine maintenance increases fuel consumption; insufficient tire pressure leads to higher fuel consumption; failing to maintain the vehicle properly results in increased fuel consumption. Ways to reduce fuel consumption: Increase tire pressure to reduce friction; remove unnecessary items from the vehicle to reduce weight; maintain a steady average speed and drive smoothly, adhering to an economical speed, which can significantly lower fuel consumption; perform regular engine maintenance; periodically clean carbon deposits and replace the air filter.
9
2
Share

What is the function of suspension stiffness adjustment?

The main function of suspension stiffness adjustment is to ensure the balance and switching between the handling and comfort of the car. The following is a related introduction about suspension stiffness adjustment: 1. Adjustment principle: The variable suspension stiffness adjustment controls the regulating valve on the shock absorber through the control unit, thereby controlling the internal hydraulic circulation of the shock absorber to change the damping coefficient of the shock absorber; 2. The meaning of suspension stiffness adjustment: Variable suspension stiffness adjustment refers to adjusting the comfort level of the vehicle suspension, generally divided into three modes: normal, sport, and comfort; It can meet the different needs of drivers at different levels. Drivers only need to operate the switch to switch modes to adapt to various road conditions, making it relatively convenient to use and operate. For example, when the vehicle is in sport mode, the chassis suspension can be adjusted to be stiffer, which will enhance the vehicle's handling and cornering support performance, improving the driving experience. 3. Types of vehicles with suspension stiffness adjustment: (1) One type allows the driver to actively control the suspension stiffness through buttons; (2) The other type adjusts the suspension stiffness automatically based on driving speed or vehicle sensor data, and the driver cannot change the suspension stiffness.
3
3
Share

Is the original invoice required when selling a used car?

Selling a used car requires the original invoice. The introduction of used cars is as follows: Introduction to the residual value rate of used cars: When buying or selling a used car, it is essential to understand a very important indicator: the residual value rate of the used car. The so-called residual value rate, in simple terms, refers to the vehicle's value retention. After several years of use, how much a car is still worth in the market depends on its residual value rate. The higher the residual value rate, the more valuable the used car is. To understand a car's residual value rate, several indicators must be clarified: whether the car has a sufficiently large market presence, whether its color is mainstream, the brand of the vehicle, and the convenience of later maintenance, among others. Precautions when selling a used car: It is crucial to sell the vehicle before its insurance expires; otherwise, an additional insurance cost will be incurred during the used car transaction. Secondly, pay attention to the replacement cycle of spare parts.
20
2
Share

How Many Days After Passing Subject 3 Can You Take Subject 4?

There are two time points for taking Subject 4 after passing Subject 3: the same day in the afternoon or one week later. Due to regional differences, the interval between Subject 3 and Subject 4 may vary. Below are the details about Subject 3 and Subject 4: Content of Subject 3 Exam: It is part of the motor vehicle driver's license assessment, referred to as the road driving skills and safe civilized driving knowledge test. The road driving skills test includes preparation before driving, simulated lighting test, starting, driving straight, gear shifting operations, changing lanes, parking by the roadside, passing intersections straight, turning at intersections, meeting vehicles, overtaking, making U-turns, and nighttime driving, among others. The test content varies for different types of vehicles. The safe civilized driving knowledge test covers safe driving operation requirements, safe driving knowledge under adverse weather and complex road conditions, and post-accident handling knowledge. Content of Subject 4 Exam: Subject 4, also known as the theoretical test or driver's theory test, is part of the motor vehicle driver's license assessment. The test consists of 50 questions randomly selected from the Subject 4 question bank in proportion. Duration: The test lasts 45 minutes. Question types include true/false questions, single-choice questions, and multiple-choice questions. The test questions include picture-based questions, scenario recognition questions, and text-based narrative questions.
18
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.