···
Log in / Register

What is the 0-100km/h acceleration time of the BYD Yuan Pro?

4 Answers
DelCarson
07/29/25 7:08pm

BYD Yuan Pro's 0-100km/h acceleration time is 9.82 seconds. Below is an introduction to the BYD Yuan Pro: Exterior: To cater to the needs of female consumers, the Yuan Pro adopts a brand-new styling design. Body dimensions: The Yuan Pro measures 4375mm in length, 1785mm in width, and 1680mm in height, with a wheelbase of 2535mm. Compared to the Yuan EV, the length has increased by 15mm, and the rear adopts a traditional taillight style. Powertrain: The Yuan Pro is equipped with lithium iron phosphate Blade Battery across the entire lineup. The energy density of the Yuan Pro's Blade Battery is 140Wh/kg, with a maximum motor power of 136 horsepower and peak torque of 210 Nm. The comprehensive range is 401km.

Was this review help?
20
5
Share
McMaggie
08/14/25 1:24pm

Personally, I think the official 0-100 km/h acceleration time of the BYD Yuan Pro, which is around 9.9 seconds, is quite suitable for my daily driving experience, especially in urban areas like commuting to and from work. Electric vehicles start quickly and quietly, without the jerky feeling of fuel-powered cars, making the acceleration process very smooth. This time isn't super fast, but it's enough for starting at traffic lights or overtaking in the city, with a higher safety factor to avoid skidding or losing control on slippery roads. I also pay attention to the economic aspect—moderate acceleration helps save battery power, extending the range and reducing charging frequency, making it more practical than those supercar-style models. Maintenance is simpler too, with fewer motor components and less likelihood of faults. In short, the 9.9-second acceleration makes the Yuan Pro a great companion for family trips, offering ample space and peace of mind.

Was this review help?
13
0
Share
Expand All
OColton
10/15/25 3:33am

I believe the BYD Yuan Pro's 0-100km/h acceleration time of approximately 9.9 seconds is quite decent in the electric vehicle segment. Based on my actual tests, this performance feels genuinely reliable. It doesn't deliver that wild push-you-back-into-the-seat sensation, but the initial response is quick, and the acceleration from 0 to 100km/h is smooth without any lag, effectively avoiding the delay issues common with traditional internal combustion engines. Compared to some entry-level gasoline-powered SUVs that often require over 12 seconds, the Yuan Pro's advantage is quite evident—it saves time while enhancing driving pleasure. Acceleration performance can also be affected by battery state and temperature, so I recommend maintaining sufficient charge to ensure optimal performance. In daily use, it's more than capable of handling various road conditions with good reliability, and coupled with the maintenance-free electric motor system, the long-term ownership costs are lower. Overall, this acceleration setup makes the car more competitive.

Was this review help?
11
5
Share
Expand All
MacOmar
11/28/25 4:24am

When driving the BYD Yuan Pro, I noticed its claimed 0-100 km/h acceleration time is 9.9 seconds, which aligns well with the efficient characteristics of electric vehicles. It offers quick starts, linear power delivery, no energy waste, low noise during acceleration, and high passenger comfort. Perfect for urban commuting - safe and economical.

Was this review help?
17
0
Share
Expand All
More Forum Discussions

What is the chassis analysis of the Lynk & Co 09?

It adopts an independent MacPherson front suspension. Chassis structure: There are no changes in the chassis suspension, with identical components and structure, featuring a combination of front MacPherson + rear multi-link setup. The performance variant also comes equipped with an on-demand four-wheel drive system. Front suspension structure: It utilizes an independent MacPherson front suspension, known for its excellent straight-line stability, steering returnability, and high handling performance. The steering knuckle assembly and front suspension upright are made of lightweight aluminum alloy, reducing unsprung mass for better handling feel. The lower control arm is constructed from double-layer steel plates welded together, with the lower control arm and its ball joint in a riveted form, fixed to the subframe with through bolts, providing a more solid driving feel. Rear suspension structure: The rear suspension upright also employs lightweight aluminum alloy material. The front lower transverse arm is made of double-layer U-shaped steel plates in an open structure, while the front upper transverse arm is a closed tube body welded from double-layer steel plates. The anti-roll bar is positioned at the front end of the rear subframe, connecting to the rear wheel uprights on both sides via vertical links, effectively reducing body roll during cornering to enhance handling and ride comfort.
15
4
Share

What are the reasons for brake failure in Citroen C-Quatre?

Reasons for brake failure in Citroen C-Quatre include excessive impurities in the brake master cylinder, failure of the vacuum booster pump, excessively dirty brake fluid or mixing several types of brake fluid leading to gas formation after heating, leakage in the brake master cylinder or wheel cylinder, leakage at the air reservoir or pipeline connections, mechanical failure due to improper operation, severe overload, etc. Lack of necessary maintenance on the brake system can lead to excessive impurities in the brake master cylinder, failure of the vacuum booster pump, excessively dirty brake fluid or mixing several types of brake fluid leading to gas formation after heating, leakage in the brake master cylinder or wheel cylinder, leakage at the air reservoir or pipeline connections, or mechanical failure due to improper operation. Prolonged downhill driving can cause the brake pads to generate heat through friction, leading to carbonization of the brake drum and complete loss of braking function. In such cases, the vehicle should be sent for inspection immediately. Severe overload increases the vehicle's motion inertia under gravitational acceleration, directly leading to brake failure. To prevent this, it is essential to avoid overloading the vehicle. When experiencing brake failure, it is crucial to overcome panic and observe road conditions. In driving, tension and panic can be fatal regardless of the situation. The driver should first calm down, clearly observe the road conditions, and regain composure to address the emergency effectively.
8
1
Share

What is the actual measured ground clearance of the Prado?

The ground clearance of the Prado is 215mm. Its length, width, and height are 4840mm, 1885mm, and 1890mm respectively, with a wheelbase of 2790mm, a curb weight of 2285 kilograms, and a body structure of a 5-door, 7-seat SUV. Minimum ground clearance refers to the distance between the lowest protruding part of the chassis and the horizontal ground when the car is parked on a level surface under rated full load conditions. In SUVs, the minimum ground clearance often determines the vehicle's off-road capability. Due to the different driving methods of SUVs compared to sedans, the minimum ground clearance in sedans or sports cars usually refers to the vertical distance between the lowest point of the body's lower contour line or the lowest component on the chassis and the ground. In SUVs, it more commonly refers to the vertical distance between the ground and the lowest component on the front or rear axle. The minimum ground clearance of sedans ranges between 110mm and 150mm. For example, the Audi A6 sedan has a minimum ground clearance of 142mm. For sedans, a larger ground clearance (over 130mm) generally means better off-road performance but poorer high-speed stability, while a smaller ground clearance (below 110mm) offers better high-speed stability but poorer off-road performance. Nowadays, models equipped with air suspension can automatically adjust the ground clearance, better meeting the dual needs of off-road capability and high-speed stability.
3
5
Share

What is the actual fuel consumption of the Outlander 2.0?

The fuel consumption of the 2.0L model is 8.7 liters per 100 kilometers. Here are the relevant details about the Outlander: 1. Powertrain: The Outlander is a compact SUV under Mitsubishi, equipped with two engines: a 2.0L naturally aspirated engine and a 2.4L naturally aspirated engine. 2. Body dimensions: The Outlander has a wheelbase of 2670 mm, with length, width, and height measuring 4705 mm, 1810 mm, and 1710 mm respectively. 3. The 2.0L naturally aspirated engine: Delivers 166 horsepower and a maximum torque of 201 Nm. This engine reaches its maximum power at 6000 rpm and its peak torque at 4200 rpm. It features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block. It is paired with a CVT transmission. 4. The 2.4L naturally aspirated engine: Produces 192 horsepower and a maximum torque of 235 Nm. This engine achieves its maximum power at 6000 rpm and its peak torque at 4200 rpm. It also employs multi-point fuel injection technology and an aluminum alloy cylinder head and block, and is matched with a CVT transmission.
17
0
Share

Will the Audi A4L Have Three LCD Screens?

Audi A4L will feature the same three LCD screens in its interior as the new generation A6L. Below are the relevant details: 1. Exterior: In terms of appearance, the new car continues the design style of the current model. The newly styled LED headlights on the front offer extremely high recognition when lit at night, along with outstanding illumination. On the side of the body, the petal-shaped aluminum alloy sports wheels, paired with the full and rounded body shape, appear more three-dimensional. At the rear, the new car still features inverted L-shaped LED taillights, which, combined with the chrome-plated dual exhaust layout below, enhance the sporty feel. 2. Powertrain: The powertrain remains the 1.4T and 2.0T engines. Among them, the 1.4T engine has a maximum output power of 110kW and a peak torque of 250Nm. The 2.0T engine is tuned with different high, medium, and low power outputs. The low-power version has a maximum power of 110kW and a peak torque of 270Nm; the medium-power version of the 2.0T engine can output up to 140kW power and 320Nm torque, while the high-power version delivers 185kW and 370Nm respectively.
11
4
Share

When to Shift Gears in Subject 3?

Subject 3 gear shifting timing details are as follows: 1. Right before left: Whether shifting up or down, it depends on the speed, which is controlled by the throttle and brake. Specifically, to shift up, first press the throttle to accelerate; to shift down, first press the brake to decelerate. After completing the acceleration or deceleration, especially when the car body shakes, quickly press the clutch with your left foot. 2. Gear shifting timing: Press the clutch with your left foot while using your right hand to shift gears. At this time, be careful not to look down at the gear position, because your focus should be on the road ahead. With only one hand on the steering wheel, you must firmly grip it to control the direction. Meanwhile, shift gears quickly with your right hand.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.