What is the 0-100 km/h acceleration time for the Atenza?

Is the Accelerator on the Left or Right?

The accelerator is on the right side of the car. In a manual transmission car, from left to right, the pedals are the clutch, brake, and accelerator; while in an automatic transmission car, the left pedal is the brake and the right pedal is the accelerator, so the accelerator is located on the right. The accelerator, also known as the throttle or gas pedal, is the control device that regulates the engine's power (thrust). In piston aircraft engines, the throttle controls the carburetor's throttle valve opening to regulate the cylinder's filling volume, thereby determining the engine's output power. In gas turbine engines, the throttle controls the metered fuel flow of the fuel regulator, thus determining the thrust generated by the engine. When driving a manual transmission car, the left foot is only responsible for pressing the clutch pedal, while the accelerator and brake pedals are both controlled by the right foot. In an automatic transmission car, the left foot is not used, and only the right foot controls the brake and accelerator pedals. If the left foot is on the brake pedal, the right foot must release the accelerator when braking. Pressing both pedals simultaneously can easily lead to dangerous situations. If the right foot controls both the accelerator and brake, when braking, the right foot must lift off and leave the accelerator pedal before pressing the brake.

6

2

Share

How to Turn on the Low Beam Headlights of the Sylphy?

Sylphy turning on the low beam headlights: Rotate the light control lever on the left side of the steering wheel towards the front passenger side. Rotating it twice turns on the low beam headlights, while rotating it once turns on the front position lights, instrument panel lights, and rear combination lights. When the headlights are on, pushing the entire light control lever forward turns on the high beam headlights, returning it to the original position turns off the high beam, and pulling it back flashes the headlights once. Below is some related information about the Sylphy's low beam headlights: 1. The low beam headlights have an illumination range of about 30-40 meters. This means that if you detect an obstacle within this range and brake immediately, there will be no gap between the car and the object. Of course, this assumes good car condition, road condition, and driver reaction time. If the speed is higher, or if the car or road condition is poor, or the driver is fatigued with a longer reaction time, it can be dangerous. Therefore, it is essential to control the speed when driving at night. 2. The difference between high beam and low beam headlights: Both are used for nighttime illumination, but the high beam has a higher angle and longer distance, while the low beam has a lower angle and shorter distance. It is generally advisable not to use high beams when driving in the city because urban areas usually have good lighting conditions. The high angle of the high beam can easily dazzle oncoming drivers and pedestrians, affecting their vision and posing safety risks. It is also considered impolite driving behavior.

5

4

Share

What grade of engine oil is suitable for the Leiling 1.2T?

Toyota Leiling 1.2T engine originally uses 5W-30 engine oil. If you want to change the engine oil during later maintenance, you can use SAE 0W-20, 5W-20, or 5W-30 engine oil. The viscosity of engine oil changes with temperature, so special attention should be paid to its performance under low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand low temperatures of -30°C. The smaller this number, the better the low-temperature fluidity, making cold starts smoother. The latter number represents the kinematic viscosity of the oil at 100°C. The higher the number, the better the oil can maintain viscosity at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the engine oil in a Toyota Leiling 1.2T is as follows: Wait for the engine temperature to drop, allowing the oil to flow back to the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan to catch the old oil until it stops flowing. Start the engine and let it run for 30 seconds to allow the oil in the main oil passage to drain out. Use a special wrench to remove the oil filter. Apply engine oil to the seal of the new oil filter and tighten it clockwise by hand. Add new engine oil through the oil filler cap on the engine valve cover, usually filling about three-quarters of the bottle. Start the engine and let it run for 5 minutes, checking for leaks around the oil drain plug and oil filter. If there are leaks, repairs should be made. After stopping the engine, pull out the oil dipstick to check that the engine oil level is within the standard range.

6

3

Share

Why was the Haval H4 discontinued?

Haval H4 was discontinued due to severe product homogenization and a high price point, which made consumers prefer other better options available at the same price range. The reasons are as follows: 1. Lack of product differentiation: The Haval H4's market positioning and segment overlap significantly with the Haval H6, which greatly impacted its sales. 2. Unsatisfactory configuration: The base model lacked front and side airbags, forcing safety-conscious buyers to incur additional costs for aftermarket installation at dealerships, further diminishing its overall competitiveness.

12

2

Share

Should You Press the Clutch Before Starting the Car?

You should press the clutch before starting the car. The reasons are as follows: 1. Reduce vehicle damage: When starting the car, you need to press the clutch because doing so can reduce the load on the engine, thereby extending its service life. Otherwise, it will cause the battery to output a larger current, affecting the engine's ignition performance. Over time, this can cause certain damage to the vehicle. 2. Prevent potential hazards: Pressing the clutch when starting the car can also prevent accidents. If you don't press the clutch before starting, the vehicle might suddenly lurch forward, which could easily lead to dangerous situations.

14

1

Share

What causes the intermittent cooling of the old Sagitar's air conditioning?

Here are the specific reasons why the old Sagitar's air conditioning sometimes cools and sometimes doesn't: 1. Dirty air filter: If maintenance hasn't been performed for a long time, the filter may be too dirty, affecting the cooling effect of the air conditioning. 2. Dirty condenser: A dirty condenser can also lead to poor cooling performance. The car's air conditioning condenser is located at the front of the vehicle and can be rinsed with a water hose. 3. Insufficient refrigerant: A lack of refrigerant in the air conditioning system's pipelines reduces pressure and results in poor cooling performance. Refill the refrigerant and check for any leaks in the air conditioning pipes.

13

2

Share

What is the 0-100 km/h acceleration time for the Atenza?

Is the Accelerator on the Left or Right?

How to Turn on the Low Beam Headlights of the Sylphy?

What grade of engine oil is suitable for the Leiling 1.2T?

Why was the Haval H4 discontinued?

Should You Press the Clutch Before Starting the Car?

What causes the intermittent cooling of the old Sagitar's air conditioning?

What items are included in Mercedes-Benz's B maintenance?

Can I re-select a license plate number if I didn't confirm it on 12123?

What does 'Selected License Plate Pending Confirmation' mean on Traffic Management 12123?

Can a car be sold if it has been mortgaged?