What is MG?

Where is the Oil Filter Located on the Atenza?

The oil filter on the Atenza is located beneath the engine. It can be removed using a specialized tool or a wrench of the same size. However, it is important to first drain the engine oil completely. There is a drain plug at the bottom of the engine; loosening it will allow the oil to drain, which should be collected in a container. Below is some relevant information about the oil filter: 1. The oil filter, also known as the oil cleaner, functions to remove debris, gum, and moisture from the engine oil, delivering clean oil to all lubrication points. To reduce friction between moving parts in the engine and minimize wear, oil is continuously supplied to the friction surfaces of moving components, forming a lubricating film. 2. Engine oil naturally contains a certain amount of gum, impurities, moisture, and additives. During engine operation, the introduction of metal particles, contaminants from the air, and the generation of oil oxidation products increase the amount of debris in the oil. If the oil is not filtered before entering the lubrication circuit, the contaminants in the oil will be carried to the friction surfaces of moving parts, accelerating wear and reducing the engine's lifespan.

2

Share

How Many Days After Applying Explosion-Proof Film Can You Open Windows?

Do not open windows or wash the car within the first three days after applying the film. Avoid opening windows as much as possible within the first week to prevent displacement, peeling, or detachment of the film due to moisture. Also, try not to use the rear window defogger within the first week, as moisture can negatively affect the defogger lines. Here are some precautions after applying car film: 1. After installation, wipe the film surface with a damp towel, sponge, or soft cloth. 2. Do not wash the windows with water within the first three days after applying the film to avoid detachment due to moisture. 3. Avoid rolling the windows up and down for the first few days after applying the film, especially for new cars. The glass is usually tight, and it takes 5-7 days for the heat-insulating film to firmly adhere to the window. During this period, the edges of the film can easily peel or roll up when opening or closing the windows, and the film may shift if not fully bonded. High-quality films typically have excellent wear resistance. For example, LLumar uses specialized high-performance resin adhesive between film layers, offering outstanding adhesion. Even with no or minimal edges (only 1-2 mm difference between the film edge and the glass edge), the film resists peeling and has excellent scratch resistance. 4. Avoid using the rear window defogger within the first week, as moisture can negatively affect the defogger lines. 5. If the film becomes loose during car washing, return to the professional installation shop for re-fixing to ensure effectiveness and durability.

19

5

Share

Which country is Lincoln Motor from?

Lincoln is a luxury vehicle brand under Ford Motor Company, founded in 1917 by Henry Leland. Its main models include: Lincoln MKZ, Lincoln Continental, Lincoln MKC, Corsair, Nautilus (imported), and Aviator. The Lincoln logo features a shining star within a rectangle, symbolizing President Lincoln as the guiding star for the unification of the United States and the abolition of slavery, and also representing the brilliance of Lincoln vehicles. Key milestones in Lincoln's development are as follows: In 1917, Lincoln launched its first vehicle, the L-Series. On February 4, 1922, Ford Motor Company acquired Lincoln Motor Company for $8 million. In 1936, Lincoln introduced an entry-level luxury car, the Lincoln-Zephyr. In 1977, Lincoln launched the mid-level luxury car Versailles. In 1998, Lincoln introduced its first SUV model, the Navigator. In 2002, Lincoln released the pickup truck model Blackwood. On December 3, 2012, Ford renamed the Lincoln division to Lincoln Motor Company. In 2014, Lincoln officially announced its entry into the Chinese market.

7

2

Share

Can water enter the engine compartment?

Here are the reasons why you should not use water to clean inside the car engine compartment: 1. It can easily damage the generator, leading to failure. 2. If the engine is hot, the sudden cooling from water can cause significant harm due to thermal expansion and contraction. The engine block may crack under strong thermal shock. 3. There are many electrical wires in the engine compartment, and exposure to water can cause issues and accelerate wire aging. If you must use water, ensure critical components are waterproofed. It is recommended to use compressed air for cleaning instead. Precautions for water cleaning: 1. Cover the generator, distributor, brake fluid reservoir, etc., with cloth or plastic bags. 2. Only rinse after the engine has cooled down. Avoid using high-pressure water jets. 3. After rinsing, thoroughly dry the engine compartment with a clean cloth, especially the underside of the hood. 4. Do not directly spray water at the air intake or electrical connectors.

1

Share

Where to Place a Fire Extinguisher in a Car?

Car fire extinguishers are mainly placed in the following locations inside the vehicle: 1. Inside the glove compartment. 2. Under the driver's seat. 3. Under the front passenger seat. 4. In the trunk. The usage methods and precautions for fire extinguishers are as follows: 1. Carry the fire extinguisher to a spot near the fire, standing upwind of the fire. 2. Pull out the safety pin. 3. Hold the nozzle with one hand and the handle with the other. 4. Aim the nozzle at the base of the flames and sweep. Precautions: The storage environment temperature for car fire extinguishers should be within the range of -10°C to 45°C, and the placement location should be kept dry and ventilated to prevent the extinguisher from getting damp and corroding.

10

4

Share

Reasons for Abnormal Noises in Car Front Shock Absorbers During Winter

Causes of abnormal noises in shock absorbers during winter are as follows: 1. Extremely low temperatures causing the shock absorber rubber to become too hard. 2. Lack of lubrication between the metal rod and shock absorber sleeve due to prolonged use. 3. Shock absorber oil leakage or gaps in the connecting ball joint. Please promptly inspect and repair the shock absorbers if the following phenomena occur: 1. Poor vehicle handling during sharp turns, with a tendency to drift towards the outside of the curve. 2. Inaccurate steering feel during large-radius turns, with a tendency for the car to sway. 3. Noticeably increased front suspension vibration transmitted through the steering wheel when driving on rough roads. 4. Dull impact noises perceptible to occupants when encountering road bumps. 5. Wheel hopping during acceleration, resulting in sluggish acceleration.

20

0

Share

What is MG?

Where is the Oil Filter Located on the Atenza?

How Many Days After Applying Explosion-Proof Film Can You Open Windows?

Which country is Lincoln Motor from?

Can water enter the engine compartment?

Where to Place a Fire Extinguisher in a Car?

Reasons for Abnormal Noises in Car Front Shock Absorbers During Winter

Which Country Does Zotye Belong To?

How Long Does It Take to Replace Antifreeze?

What are the reasons for the Honda Fit's air conditioning not cooling?

How often should AT transmission fluid be changed?