What is a mist cannon truck used for?

1 Answers
VonCarter
07/30/25 5:30am
A mist cannon truck is a high-tech air purification device used in urban sanitation operations. Below is an introduction to its related functions: 1. Principle: This type of mist cannon truck can spray micron-level water mist particles. The rapidly flowing water mist comes into contact with airborne dust, dirt, and other particulate matter, accelerating their descent under gravity, quickly forcing floating pollutants in the air toward the ground. It decomposes and dilutes the concentration of PM2.5 particles in the air, effectively controlling the amount of airborne pollutants and dust, achieving the effect of cleaning and purifying the air and alleviating smog. Tests by environmental protection departments have shown that the "mist cannon" can reduce the concentration of fine particles in the air by about 15%. 2. Functions: In addition to its dust suppression function, this mist cannon truck also has multiple functions such as sprinkling and road washing. Moreover, compared to ordinary sprinkler trucks, the mist cannon truck sprays water mist over a wider area with less water consumption, making its work efficiency and water resource utilization relatively higher. For the same ten tons of water, an ordinary sprinkler truck can only spray for ten minutes, while a new mist cannon truck can spray for over an hour, covering an area of more than 30,000 square meters, greatly improving water resource utilization.
Was this review help?
7
0
Share
More Forum Discussions

How to Fix a Locked Rear Wheel on a Car?

Generally, if the brake drum gets wet after washing the car or in the rain and the handbrake is applied, leaving it parked for a long time can cause the wheel to lock up. You can fix it by sanding with sandpaper and applying grease. If the issue is with the wheel cylinder itself, it may need to be replaced directly. This can prevent the brake pads from separating on their own: Depending on the situation, the brake pads may need to be sanded or replaced directly.
5
1
Share

How to Remove the Letters on the Back of a Car?

This is the most primitive method, but generally, the emblems are stuck quite firmly. Trying to peel them off by hand may scratch your fingers and make it difficult to remove them. If you have fishing line or a thin card at home, you can use it to scrape off the emblem. Using hot water or a hairdryer is the simplest method. The principle is to heat and melt the adhesive, making it much easier to peel off. This is the most commonly used method for removing emblems.
17
1
Share

What to Do When the Car Cannot Detect the Key and Fails to Start?

There may be signal interference sources in the current location. Even after entering, the key cannot be detected, and the solution is to directly place the key near the push-button start. The key battery might be dead, or there could be battery issues or leakage causing the power to drain prematurely. This issue often occurs due to the key chip being unreadable or potential malfunctions in the transmitter or receiver.
17
3
Share

What to Do When a Car Gets Flooded?

Disconnect the negative terminal of the battery as soon as possible to prevent short circuits in various electrical components due to water ingress. Immediately inspect the engine, first checking if water has entered the engine cylinders, as this can cause the connecting rods to bend and damage the engine.
14
3
Share

How to Apply for a Motorcycle Endorsement on a Car Driver's License?

You must have held the driver's license for more than 1 year, and no 12-point penalty has been recorded in the current scoring cycle and the latest scoring cycle prior to application. Bring your ID card and driver's license to the local driving training institution or the traffic police team's driving management window to apply for the endorsement. The driving management department will arrange for you to undergo a physical examination. The driving management department will verify and certify your driving qualification information based on the computer data management system.
6
4
Share

How to Clean Car Mats?

During the cleaning process, you can appropriately add detergent, but be careful not to use overly corrosive ones. After washing, you can vigorously shake off the excess water and then let it dry completely. For fabric materials, avoid direct water rinsing as water seeping into the sponge layer can cause mold. For leather materials, simply wipe with a damp cloth and allow it to air dry naturally. Generally, it's not recommended to wash furry mats with water because they take a long time to dry. In such cases, using a vacuum cleaner to remove dust is sufficient.
1
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.