What engine does the Everus S1 use?

How to Turn Off the Auto Start-Stop Function in Chevrolet Equinox?

Chevrolet Equinox's auto start-stop function cannot be manually turned off as there is no corresponding switch in the vehicle. However, it can be permanently disabled by enabling hidden settings. The primary purpose of the auto start-stop function is to save energy and reduce emissions. Here are some considerations for using the auto start-stop and auto hold functions: 1. The auto start-stop function temporarily shuts off the engine. Without the auto hold function, you cannot release the brake pedal. Releasing the brake pedal will immediately restart the engine. 2. The auto hold function compensates for the shortcomings of auto start-stop by locking the wheels for the driver, eliminating the need to keep the brake pedal pressed continuously. 3. Pressing the accelerator pedal serves as the release signal, at which point the vehicle will start moving again.

20

2

Share

How to Check if the Transmission Fluid is Sufficient?

Methods to check the transmission fluid are as follows: 1. After starting the vehicle, pull out the transmission fluid dipstick to check the scale. The normal level should be between the high and low marks. 2. There is an inspection screw on the side of the transmission. After removing this screw, if transmission fluid flows out, it indicates that the transmission fluid is sufficient. The functions of the transmission are as follows: 1. Change the transmission ratio to expand the range of torque and speed variation of the driving wheels, adapting to frequently changing driving conditions while keeping the engine operating under favorable conditions. 2. Allow the vehicle to reverse while maintaining the same engine rotation direction. 3. Use neutral gear to interrupt power transmission, enabling the engine to start, idle, and facilitating gear shifting or power output.

8

4

Share

Can You Shift to P Gear After an Automatic Car Stalls?

You can shift to P gear after an automatic car stalls. Here is the relevant content introduction: The gears of an automatic car are as follows: 1. P gear is the parking gear, used for long-term parking of the vehicle. 2. R gear is the reverse gear, which is engaged when the vehicle needs to move backward. 3. N gear is the neutral gear, which is engaged when the vehicle is parked for a short time without stalling. 4. D gear is the drive gear, and when the gear lever is placed in D gear, the vehicle will automatically shift gears based on throttle opening and speed data. 5. S gear is the sport mode, and M gear refers to the manual mode, where gear shifting is done manually by the driver when the gear lever is in M gear. 6. L gear is the low gear.

14

5

Share

What to Do If the Accelerator Pedal Vibrates?

The causes of accelerator pedal vibration are as follows: 1. Resonance from the engine is transmitted to the accelerator pedal through the vehicle body. 2. Prolonged driving leads to a dirty throttle, causing it not to close properly and resulting in high idle speed of the car engine. 3. Excessive carbon buildup produced during the operation of the car engine. Solutions are as follows: 1. Clean the car's fuel system and throttle, check if the throttle is blocked, and inspect if the fuel injectors have excessive carbon deposits. 2. Check the engine mounts. 3. The car should be regularly maintained, and the car oil should be replaced.

16

1

Share

How to Know If Engine Oil Level is Too High

Methods to check for excessive engine oil are as follows: 1. Park the car on a relatively level surface, turn off the engine and wait for more than five minutes to allow the oil to fully drain back. 2. Open the engine compartment, locate the oil dipstick, pull it out, and check if the oil level is between the two marks on the dipstick. 3. To ensure accuracy, first wipe the dipstick clean with a paper towel, then reinsert it into the engine. The main reasons for excessive engine oil are as follows: 1. Oil mixed with gasoline or water. 2. Insufficient cylinder pressure or poor cylinder sealing, which can reduce engine power and make starting difficult. 3. Temperature conditions.

1

4

Share

What is the mileage for the first maintenance of Honda Vezel?

Honda Vezel's first maintenance should be performed when the vehicle reaches 5,000 kilometers or six months, whichever comes first. The main tasks include changing the engine oil and oil filter, as well as monitoring other items. Below are some points to note regarding the first maintenance of Honda Vezel: 1. For the first maintenance, only the engine oil and oil filter need to be replaced. Free checks such as tire pressure and lighting should also be performed. The period from when the new car is driven until the first maintenance is called the break-in period. During this period, since the gears of the engine and transmission have not fully broken in smoothly, it is generally advised not to drive too fast, definitely not exceeding 100 km/h, and preferably not exceeding 80 km/h. 2. During the break-in period, besides not exceeding 100 km/h, the engine speed should also not exceed 3,000 rpm. Avoid aggressive acceleration, as it is not good for engine break-in. A proper break-in will result in fewer driving issues and better fuel efficiency in the future. 3. After the new car is driven, the 4S shop usually requires the owner to perform the first maintenance within 3,000 kilometers. It is crucial not to exceed 5,000 kilometers before the first maintenance.

18

3

Share

What engine does the Everus S1 use?

How to Turn Off the Auto Start-Stop Function in Chevrolet Equinox?

How to Check if the Transmission Fluid is Sufficient?

Can You Shift to P Gear After an Automatic Car Stalls?

What to Do If the Accelerator Pedal Vibrates?

How to Know If Engine Oil Level is Too High

What is the mileage for the first maintenance of Honda Vezel?

What to Do When the Engine Fault Light Comes On in a Car?

Why is it called Dongfeng Infiniti?

What Causes High Temperature in a Car Radiator?

Where is the Buick Excelle produced?