What does the Navigation Guided Pilot system mean?

2 Answers
McReed
07/24/25 8:22am
Navigation Guided Pilot (NGP), simply put, means that after setting the destination on the vehicle's system, the car will automatically cruise, change lanes, and navigate nearby ramps according to the route. Additional information: 1. Brake Assist System: In emergency situations, 90% of drivers do not brake decisively. The Brake Assist System is designed to address this issue. It detects the situation the vehicle is encountering based on the speed at which the driver presses the brake pedal. When the driver quickly presses the brake pedal in an emergency but does not apply enough force, the system assists and increases the braking force to the maximum in less than a second, reducing the braking distance in emergency situations. 2. Parking Assist System: The Parking Assist System includes ultrasonic sensors embedded in the front and rear bumpers. Each sensor has a diameter of about 15mm. The ultrasonic detection signals emitted by the sensors reflect when they encounter obstacles. After receiving the reflected signals, the sensors promptly feed them back to the system for distance calculation and alert the driver through sound, video, etc., about the distance between the vehicle and obstacles outside the driver's field of vision.
Was this review help?
14
4
Share
LeMarcus
08/11/25 4:00am
I often use the navigation assist for my daily commute, which is essentially a combination of intelligent cruise control and lane keeping. Once I set the speed on the highway, the car can automatically accelerate or decelerate based on the vehicle ahead and steer through curves on its own. However, the steering wheel sensors constantly check if I'm holding it, and an alarm will sound if I don't touch it for more than ten seconds. Some newer models now even have an automatic lane-changing and overtaking feature, where the car will change lanes by itself when the turn signal is activated, but it's quite annoying that the radar often fails in rainy or foggy conditions. Ultimately, it's just an aid to reduce driving fatigue, not autonomous driving.
Was this review help?
20
3
Share
Expand All
More Forum Discussions

When to Use Manual Mode in a Tiptronic Transmission Car?

When to use manual mode in a Tiptronic transmission car: 1. When climbing long steep slopes: The driver can switch to manual mode and engage 1st gear, which limits the vehicle to lower gear operation. This provides stronger climbing power and protects the transmission; 2. When descending long slopes: The driver should also use manual mode to keep the transmission in lower gears, thereby controlling speed without prolonged brake application, preventing brake overheating that could affect braking performance; 3. When accelerating to overtake: For quick overtaking, the driver should switch to manual mode and downshift first. The vehicle can then utilize the high torque of lower gears for instant acceleration, completing the overtaking maneuver more quickly.
12
0
Share

How Long After Replacing Car Glass Can You Drive?

It mainly depends on which part. If it's the side window glass, you can drive immediately after replacement. If it's the windshield, you need to wait at least a day and a half, as insufficient drying time for the adhesive may lead to water leakage. Depending on the quality of the adhesive and seasonal factors, the complete drying cycle generally ranges from one to three days. During this period before the adhesive is fully dry, here is some relevant information: 1. Precautions: To prevent wind and water leakage, avoid washing the car for three days, and remove the tape fixing the windshield position only after three days; drive smoothly, avoiding sudden braking and rapid acceleration; try to avoid driving on excessively bumpy roads to prevent the windshield from shifting. 2. Windshield: The windshield is made by bonding a transparent adhesive plastic film between two or three layers of glass, combining the toughness of plastic with the hardness of glass, thereby enhancing the glass's resistance to breakage.
17
4
Share

What does the Buick Excelle 6-speed DSS intelligent start-stop transmission mean?

It refers to the system that controls the engine start and stop. Here is more related information: How the start-stop system works: 1. The working principle of the start-stop system is that when the vehicle stops moving due to congestion or at an intersection, the driver presses the brake pedal and shifts to neutral. At this time, the Start/Stop system automatically detects: the engine is idling and not in gear; the wheel speed sensor of the locking system shows zero; the electronic battery sensor shows there is enough energy for the next start. 2. After these three conditions are met, the engine automatically stops running. When the traffic light turns green, the driver presses the clutch, and then can activate the "start-stop device" to quickly start the engine. In automatic transmission models, as soon as the brake is released or the steering wheel is turned, the engine will automatically ignite immediately, and the driver can step on the accelerator to start, with the whole process remaining in D gear.
13
1
Share

What is the real reputation of Chery Exeed TXL?

Chery Exeed TXL's reputation is introduced as follows: 1. Power aspect: The new-generation 1.6TGDI engine delivers a power of 145KW and a torque of up to 290Nm, paired with an efficient 7-speed dual-clutch transmission, a reliable and safe chassis system meticulously crafted by Benteler, and BorgWarner's intelligent all-wheel drive system. 2. Configuration aspect: It features 11 ADAS advanced driver assistance systems leading in its class, the new-generation BOSCH 9.3 electronic stability control system, and endorsements from a host of global top-tier suppliers. The concept of industry-leading full travel service, in collaboration with internet service brands, enhances consumers' travel experience. Through partnerships with platforms like Autohome and Chexiang, it provides more convenient after-sales maintenance services and a premium technology experience in-store.
14
1
Share

Where is GAC Honda Produced?

GAC Honda's manufacturing plants are located in Guangzhou. Here is more relevant information: Introduction to GAC Honda: 1. GAC Honda Automobile Co., Ltd. (formerly Guangzhou Honda Automobile Co., Ltd.; abbreviated as GAC Honda) was established on July 1, 1998, as a joint venture between Guangzhou Automobile Group Co. and Honda Motor Co., Ltd. of Japan, with each party holding a 50% stake and a cooperation term of 30 years. 2. GAC Honda currently has two production bases: Huangpu Plant and Zengcheng Plant, with a combined production capacity of 480,000 vehicles per year and a total area of 1.6 million square meters. GAC Honda has a total workforce of over 8,000 employees. Currently, GAC Honda produces seven major series of vehicles, including the Avancier SUV series, Accord sedan series, Odyssey multi-purpose series, Lingpai sedan series, City sedan series, Fit sedan series, and the independent brand Everus series, totaling over 30 models.
15
2
Share

Why Did the Car Display Turn Blue?

The reasons for a display turning blue are varied and generally fall into three categories: display malfunction, poor signal transmission quality of the display data cable, and issues with the host graphics card. The troubleshooting method involves first testing the display on another host and replacing the cable. If the problem persists, it is likely a fault with the display itself. The lifespan of the LCD panel is quite long, so the issue is often due to aging backlight tubes emitting incorrect light. Below is relevant information: 1. Software Issue: The graphics card driver may not be properly installed. Even without a driver, the display should correctly show all colors without losing primary colors. However, incorrect driver installation can lead to this problem, such as mismatched graphics card and driver types or version inconsistencies. 2. Display Issue: Hardware malfunction in the display. Many factors can cause hardware problems, such as aging CRT tubes, environmental humidity leading to oxidized circuits, static electricity, etc., all of which can result in abnormal color display. Different solutions should be applied based on the cause, such as placing the display in a well-ventilated area.
9
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.