What does the abolition of provincial expressway toll stations mean?

1 Answers
MacConnor
07/29/25 6:03pm
Highway provincial boundary toll stations being abolished means the removal of toll stations at provincial borders, utilizing methods like ETC to achieve seamless passage. Additional information is as follows: 1. Toll Stations: Toll stations are facilities used to collect tolls from passing vehicles. Toll roads or toll interchanges must have toll stations. There are generally two types of toll station locations: one is directly set on the main line, also known as a barrier type, mostly used at the start and end points of toll sections on the main line; the other is set on interchange ramps or connecting lines, generally used for interchange points between toll sections on the main line to control vehicles entering and exiting the main line from intersecting roads. 2. Mainline Toll Stations: Mainline toll stations refer to toll stations set on the main line. In a closed toll system, besides one mainline toll station at each end of the expressway, the rest are located on ramps. In an open toll system, toll stations or mainline/ramp barrier-type mainline toll stations are typically set at certain intervals along the expressway, with bidirectional toll stations. The disadvantage of mainline toll stations is that the anticipated high traffic volume may require toll plazas to be too wide, making the road right-of-way impractically broad, leading to difficulties in land acquisition and potential issues such as insufficient minimum turning radius.
Was this review help?
13
4
Share
More Forum Discussions

Why Shouldn't You Press the Clutch and Accelerator Simultaneously?

Pressing the clutch and accelerator together is ineffective. Engaging the clutch is equivalent to shifting into neutral, rendering any accelerator input useless and wasting fuel. After driving for a while, you'll find that when upshifting, you should first fully depress the clutch, then release the accelerator, and gradually release the clutch while slowly applying throttle to prevent the car from jerking. Below are some taboos for starting a car: 1. Avoid unstable starts: Starting is the first step in vehicle operation. A proper start should be smooth and safe, with the correct driving posture—eyes on the road ahead and both sides, not looking down at the controls. Ensure no lurching, shaking, stalling, or intermittent surging occurs during startup. 2. Avoid inappropriate gear selection: The choice of starting gear depends on specific conditions like road surface and slope. Generally, use 1st or 2nd gear on flat, solid roads or grounds. In extreme cold, loose soil, or uphill conditions, always start in 1st gear. Similarly, use 1st gear on icy, snowy, or muddy roads, and clear any snow, mud, or spread sand under the wheels for better traction.
10
4
Share

What brand is the Santana manual transmission?

The brand of the Santana manual transmission is Volkswagen. In 2007, Volkswagen Automatic Transmission (Dalian) Co., Ltd. was established. Its business includes the research, development, production, assembly, and sales of automotive transmissions and components, as well as related technical services and after-sales services. The Santana manual transmission uses a 5-speed manual gearbox. The 5-speed manual transmission features a two-shaft layout, eliminating the conventional intermediate shaft, and integrates with the drive pinion and differential as a longitudinally mounted front-wheel-drive transmission. Engine power is input through the input shaft, gear changes are made via the gear set, and the output shaft, final drive gear, and differential gear set are used to drive the front wheels. For the Santana's transmission in daily use, the following points should be noted: Do not delay changing the transmission oil for extended periods. Prolonged failure to change the transmission oil can damage internal components such as bearings and the housing. Avoid prolonged coasting in neutral. While driving a manual transmission vehicle, many experienced drivers may coast in neutral, but for automatic transmissions, this can lead to overheating and a noticeable jolt when shifting back into Drive (D). Never shift into Drive (D) or Reverse (R) before the vehicle comes to a complete stop. Some drivers, aiming for smooth operation, shift into reverse while the vehicle is still moving, which can severely damage the transmission gears and lead to gear grinding over time. Avoid frequently climbing steep hills in Drive (D). Automatic transmission vehicles may overheat under high load or shift too early, resulting in insufficient power for climbing. In such cases, use manual mode to lock in lower gears or switch to sport mode to protect the transmission. Do not tow the vehicle over long distances. If an automatic transmission vehicle breaks down, use a flatbed tow truck to move the vehicle onto the tow platform while it is in Neutral (N). Avoid using tow ropes or directly towing the vehicle with another vehicle.
2
5
Share

What are the reasons why the Santana doesn't move when in gear?

The reasons why the Santana doesn't move when in gear are as follows: 1. In neutral: The gear is not engaged and is still in neutral; reverse gear usually doesn't have a synchronizer. Although most gear shifts can be engaged through the gear's chamfer, there are times when the gears cannot mesh due to alignment. In such cases, simply lift the clutch slightly to allow the input shaft to rotate and realign the gears. 2. Handbrake not released: The handbrake is not released, and the car remains in manual braking mode, preventing movement. 3. Clutch not released: The clutch is still disengaged, and no power is being transmitted. 4. Synchronizer stuck: The synchronizer for the gear in the transmission is stuck. If other issues arise, professional repair is needed.
19
3
Share

How often should Audi change the engine oil?

Audi manufacturers recommend changing the engine oil every six months or 7,500 kilometers, and replacing all vehicle fluids every three years or 60,000 kilometers. However, these are relatively conservative recommendations. The specific time for changing the engine oil can be adjusted based on the usual driving conditions of the car, allowing for flexibility around the recommended intervals. The frequency of oil changes is also related to the type of oil used. The oil change frequency recommended by Audi manufacturers is merely a suggestion, as everyone's driving habits and the road conditions vary. For example, if driving frequently in harsh environments, the frequency of maintenance and oil changes can be increased, and servicing can be done earlier than the standard intervals. If driving habits are more relaxed and the vehicle operates under normal conditions, maintenance and oil changes can be appropriately delayed to save costs. In particularly harsh environments, it may be advisable to change the car's engine oil annually, especially when replacing the air filter. The cleanliness of the air filter's intake directly affects the lifespan of the engine oil. Therefore, it's not only important to focus on the engine oil but also to monitor the condition of the air filter and oil filter. The role of the air filter is also crucial during vehicle operation.
20
3
Share

What Are the Effects of a Cracked Turbo Intake Pipe?

It can cause vehicle shaking, insufficient engine power, increased fuel consumption, and the illumination of the engine fault light. It is necessary to check or replace it at a repair station as soon as possible. The engine intake hose is generally located between the throttle valve and the engine intake valve. The intake pipe is the main air intake passage, while the intake manifold distributes air to each cylinder to support combustion. The air passes through the carburetor to atomize the gasoline, which then enters the cylinders with the air. Below is a related introduction: 1. Engine intake passage: The engine intake passage is the channel for air to enter and exit the air cleaner. The intake pipe connects the air cleaner to the carburetor manifold, and the intake manifold connects the bottom of the carburetor to the cylinder intake valve. 2. Performance: The intake pipe includes the main intake pipe and the branch intake pipes. In addition to power performance, the engine must also have good fuel economy and emission performance. In gasoline engines, the intake pipe must also consider issues such as fuel atomization, evaporation, distribution, and the utilization of pressure waves. In diesel engines, airflow through the intake passage is required to form intake swirl in the cylinders to improve mixture formation and combustion.
19
0
Share

Why does a lower gear provide greater traction?

Lower gears result in greater torque output to the drive wheels, thereby increasing traction. Here are the reasons: 1. Principle behind greater traction in lower gears: Automobile engines have two key parameters—engine power (measured in horsepower) and torque (measured in Newton-meters). Higher engine power means the engine can run faster, while greater torque translates to stronger traction and quicker acceleration. In simple terms, "power" indicates how fast the engine can rotate, whereas "torque" represents the force the engine can deliver to the wheels during friction between the tires and the ground. Power and torque cannot be maximized simultaneously; torque typically sees significant gains at low speeds, while maximum engine power generally remains constant. When climbing a slope, a vehicle requires greater torque to overcome both the friction between the tires and the ground and the gravitational force pulling the car downhill. Hence, downshifting is necessary when ascending a slope. 2. Physics formulas: (1) W=Fs=Fvt (Work = Force × Distance = Force × Velocity × Time); (2) P=W/T (Power = Work ÷ Time); Combining these two, P=Fv. When shifting to a lower gear, speed decreases, leading to an increase in traction.
17
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.