What Could Be the Reason for No Response When Inserting the Key into a Motorcycle?

What's the reason for the transmission not shifting gears?

Transmission not shifting gears may be caused by transmission oil pump failure, transmission valve body failure, control module failure, and other reasons. The relevant introduction to the transmission is as follows: 1. Function: The transmission is a gearbox that changes the transmission ratio and direction of motion, located between the clutch and the central drive. Its main functions are to change the vehicle's driving force and speed (shifting) when the engine speed and torque remain unchanged, to enable the vehicle to drive in reverse (direction change), and to allow the engine to stop without stalling (neutral). 2. Classification: According to the transmission type, gear-type transmissions can be divided into three types: double-shaft type, three-shaft type, and composite type. The double-shaft type has two main shafts (excluding the reverse gear shaft) and only undergoes one pair of gear reduction. The three-shaft type has three main shafts (first shaft, intermediate shaft, second shaft) and undergoes two pairs of gear reduction. The composite type consists of two transmissions connected in series or parallel to obtain more gear positions with fewer gears.

8

4

Share

What is the license plate code for Weifang?

Weifang license plate code: Lu G, Lu V. Weifang is a prefecture-level city under the jurisdiction of Shandong Province. Shandong is abbreviated as Lu, located in the central part of the Shandong Peninsula, adjacent to Qingdao, Rizhao, Zibo, Yantai, Linyi, and other places. The license plate codes for other cities in Shandong Province are: Lu A for Jinan, Lu B for Qingdao, Lu C for Zibo, Lu D for Zaozhuang, Lu E for Dongying, Lu F for Yantai, Lu G for Weifang, Lu H for Jining, Lu J for Tai'an, Lu K for Weihai, Lu L for Rizhao, Lu M for Binzhou, Lu N for Dezhou, Lu P for Liaocheng, Lu Q for Linyi, Lu R for Heze, Lu S for Laiwu, Lu U for Qingdao, Lu Y for Yantai.

13

0

Share

Is It Normal to Drive at 80 km/h in Fourth Gear?

Driving at 80 km/h in fourth gear is not normal and is considered low-gear high-speed driving, which results in high fuel consumption and can damage the engine. There are three key points for engine maintenance: 1. Clean the air filter: The air filter is crucial for the engine's air intake during driving. If the air filter is clogged or accumulates excessive dust, it will restrict the engine's air intake. Additionally, a large amount of dust entering the cylinder will accelerate carbon buildup, leading to poor ignition, reduced power, and naturally increased fuel consumption. 2. Remove throttle valve sludge: Sludge forms due to carbon deposits from fuel combustion exhaust at the throttle valve and residues of impurities not filtered by the air filter. Excessive sludge can cause air resistance, leading to increased fuel consumption. 3. Clean injector carbon deposits: The combustion chamber is prone to carbon buildup, which can make starting difficult. Carbon deposits on the injector can also clog fuel passages, distort gasoline injection, and reduce atomization, naturally increasing fuel consumption.

9

2

Share

What is the content of the small car Subject 3 driving test?

The content of the small car Subject 3 driving test includes: preparation before getting on the car, simulated light test, starting, driving in a straight line, shifting gears, changing lanes, pulling over, going straight through intersections, turning left at intersections, turning right at intersections, passing pedestrian crossings, passing school zones, passing bus stops, meeting oncoming vehicles, overtaking, making U-turns, and driving at night. Subject 3 safe and civilized driving knowledge test content: Requirements for safe and civilized driving operations, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods in situations such as tire blowouts, and post-accident handling knowledge. Precautions during the Subject 3 test: During the preparation stage before starting, after confirming identity information, walk around the car to observe the vehicle condition and surrounding traffic. After getting in the car, adjust the left and right rearview mirrors and seat, fasten the seat belt, turn on the left turn signal when starting, press the clutch and brake properly, shift into first gear for a smooth start, and shift gears according to the speed. When driving straight, pay attention to the front, keep the car between the two lane markings, avoid holding the steering wheel too tightly. If the car deviates, slightly adjust the steering wheel and occasionally check the rearview mirror briefly. Before changing lanes, turn on the turn signal five seconds in advance, observe the road conditions through the rearview mirror and look back to confirm safety before changing lanes. Before overtaking, turn on the turn signal five seconds in advance, observe the rear and left road conditions through the rearview mirror, look back to confirm safety. After completing the overtaking and returning to the original lane, observe the rear and right road conditions and look back to confirm safety.

15

2

Share

What is the Two-Row Non-Adjustment Valve Method?

The two-row non-adjustment valve method is a simple and feasible approach to confirm the adjustability of valve clearance. Below is relevant information about automotive valves: 1. Introduction: The function of valves is specifically responsible for introducing air into the engine and expelling exhaust gases after combustion. Structurally, they are divided into intake valves and exhaust valves. The intake valve's role is to draw air into the engine to mix with fuel for combustion, while the exhaust valve's role is to expel the burned exhaust gases and dissipate heat. 2. Composition: Valves consist of a valve head and stem. The valve head operates at very high temperatures (intake valve: 570~670K, exhaust valve: 1050~1200K) and also withstands gas pressure, valve spring forces, and the inertial forces of the transmission components. With poor lubrication and cooling conditions, valves must possess certain strength, stiffness, heat resistance, and wear resistance. Intake valves are typically made of alloy steel, while exhaust valves are made of heat-resistant alloy silicon-chromium steel.

2

3

Share

How to Reset the Maintenance Light on Peugeot 3008?

Peugeot 3008 maintenance light reset method: 1. Turn off the ignition switch of the Peugeot 3008; 2. Press and hold the maintenance mileage reset button; 3. Press the single trip meter reset button on the combination instrument panel, and the odometer display will start the countdown; 4. When the display shows "equal to 0", it means the maintenance indicator light has been reset; 5. After releasing the reset button, the wrench symbol (maintenance indicator light) will turn off. The Peugeot 3008 has dimensions of 4435mm in length, 1840mm in width, and 1652mm in height, with a wheelbase of 2613mm. It is a 5-door, 5-seat SUV, equipped with a 6-speed automatic transmission and a 1.6T L4 turbocharged engine.

5

1

Share

What Could Be the Reason for No Response When Inserting the Key into a Motorcycle?

What's the reason for the transmission not shifting gears?

What is the license plate code for Weifang?

Is It Normal to Drive at 80 km/h in Fourth Gear?

What is the content of the small car Subject 3 driving test?

What is the Two-Row Non-Adjustment Valve Method?

How to Reset the Maintenance Light on Peugeot 3008?

What does a four-door five-seater sedan mean?

Will driving 10 kilometers after a flat tire damage the wheel rim?

What are the buttons on an automatic transmission car's gear shift?

What is the correct way to release the clutch pedal?