What Causes a Car to Skid?

1 Answers
Dawson
07/29/25 3:20pm
Detailed explanation about car skidding is as follows: 1. Reasons for car skidding. Car skidding can be caused by sudden acceleration, improper braking, excessive torque during startup, slippery roads due to oil, dirt, or ice, as well as reduced tire grip coefficient and asymmetry between left and right tires. 2. Types of car skidding. There are three types of car skidding: four-wheel skidding, front-wheel skidding, and rear-wheel skidding. Car skidding, especially rear-wheel skidding, poses a significant threat to safe driving and often leads to severe traffic accidents such as collisions, rollovers, or running off the road. Once a vehicle starts to skid, the first thing to do is to hold the steering wheel steady, ease off the accelerator as needed, and avoid panicking. Do not rely on instinct to steer blindly.
Was this review help?
9
3
Share
More Forum Discussions

How to Replace the Battery in a Mercedes-Benz A200 Key?

Press the small switch on the back of the key to remove the mechanical key. Press the key back cover opening button on the back of the key and remove the back cover. Then push the battery compartment on the left side of the key to remove the old battery. Ensure the new battery is installed with the positive side facing upwards, then reattach the key cover and mechanical key.
3
5
Share

How to Adjust the Height of High Beam Headlights?

The first knob next to the headlight switch can be used to adjust the height. Turn it upwards to raise the beam and downwards to lower it. Open the engine hood, and you will find a white cross-shaped knob on the headlight box in the engine compartment. Use a cross screwdriver to turn it left or right to adjust the height.
10
2
Share

How to Replace the Key Battery for Zotye T600?

Press the silver round button at the upper right corner and pull out the mechanical key; do not fully remove the mechanical key—leave a portion inside. Flip the key over so the side with the "Z" logo faces upward; pry open the remote battery cover. Hold the key firmly with one hand, keeping the mechanical key inserted about one-third of the way; separate the key completely along the gap. Remove the black plastic battery holder; take out the old battery and replace it with a new one.
9
4
Share

How to File an Insurance Claim After a Car Accident?

After receiving the report, the insurance company will quickly dispatch its claims adjuster to investigate the accident. The damaged vehicles and property will be assessed to determine the loss amount according to regulations. For accidents involving injuries, immediately call the 120 emergency number to send the injured to the hospital for treatment. Once the relevant liabilities are clarified, both parties involved in the accident will undergo mediation by the traffic police department in accordance with laws and regulations. The responsible party will then fulfill their respective compensation obligations to conclude the case.
16
3
Share

How to Choose Between Santana and Jetta?

The air vents of the new Santana are rectangular, while those of the Jetta are circular. Other changes are minor and not worth delving into. The new Jetta has slightly better configurations, but these are very minor and do not involve substantial changes in features.
2
1
Share

How to Install ETC?

ETC installation process is as follows: Upon receiving the device, first check if the ETC card and electronic tag (OBU) are damaged. Press the anti-tamper button on the back of the OBU, the red light will briefly illuminate, and the OLED screen will display "Label Invalid" or "Please Insert Card," indicating the device is functioning properly. Clean the front windshield, ensuring the glass surface is smooth, clean, and dry. Then peel off the adhesive backing of the OBU and stick it to the installation position. Press firmly for 2-3 minutes to remove any air bubbles. Insert the ETC card with the front side facing the driver and the back side facing the windshield, ensuring the chip is inserted into the OBU device. ETC installation requirements: For small vehicles such as cars and minivans, the OBU device should be installed in the upper middle part of the front windshield. For large vehicles like trucks and buses, the installation position should be in the lower middle part. ETC installation position requirements: the height should be no less than 1.2 meters and no more than 2.5 meters; the installation angle N should be between 30º and 90º (the angle between the electronic tag surface and the horizontal plane).
1
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.