What car brand is the slanted V?

What to Do When the Mercedes-Benz AC Blows Hot Air Instead of Cold?

There is a switch for hot air in the car, usually indicated by red and blue colors. The red side is for warm air. Turn it to the red side and then turn on the fan switch. First, start the engine to warm it up. Wait until the engine temperature needle reaches the middle position, then turn on the heating AC and set the air circulation to external circulation.

8

2

Share

How to Replace the Roof Lining of a 2010 Octavia?

First, remove components such as the sun visors, dome light, and handles. Clean the roof lining thoroughly, organize all the wiring, flatten the front seats, and pull the roof lining out from the rear door. Make holes in the fabric, apply adhesive, and after it has firmly set, reinstall the removed components.

7

2

Share

What Gear Should an Automatic Transmission Car Be in When Warming Up?

It is safer to warm up an automatic transmission car in P (Park) gear as this locks the tires. Warming up in N (Neutral) gear may cause the car to roll if the ground is uneven, even with the handbrake engaged. Below is an introduction to the gears of an automatic transmission car: 1. P (Parking): Engaging P gear after the car stops prevents movement through braking. Some models now feature an independent P gear, referred to as electronic braking. 2. R (Reverse): This gear can only be engaged when the vehicle is stationary for reversing. Models with a lock button require pressing the button to switch. 3. N (Neutral): Use this gear for temporary stops, such as at traffic lights, and always engage the handbrake. 4. S (Sport): The difference between D and S gears is simply the computer switching to different shifting programs, so S gear can be engaged at any time without adverse effects like damaging the transmission. 5. D (Drive): The most commonly used gear for driving forward, where gear changes are controlled by the accelerator. D1 (or L gear), D2, and D3 correspond to manual transmission gears 1 and 2, 3 and 4, and 5 and 6, respectively.

19

1

Share

What are the starting procedures for the BYD Han?

In the event of an emergency while the vehicle is in motion, the engine can be shut off by pressing the engine start/stop button for more than 3 seconds or by pressing it three times consecutively. If the engine stalls while the vehicle is in motion, shift the gear lever to the N (Neutral) position and press the engine start/stop button to restart the engine.

4

2

Share

What to Do When Honda Car CAN Communication Fails?

Check which module is unable to communicate. Read the fault codes of the body module, ABS module, and airbag module separately. Then measure the resistance between pins 6 and 14 of the diagnostic socket to see if it is 60 ohms or 120 ohms. A reading of 120 ohms indicates a damaged module.

19

3

Share

How to Use the Cruise Control on MG6?

The cruise control of MG6 is operated via the stalk switch located at the lower left side of the steering wheel. When the cruise control system is in standby mode, press the "Set" button at the end of the stalk switch, and the indicator light on the instrument panel will turn green, indicating the cruise system is activated. Relevant instructions are as follows: 1. The MG6 cruise control is operated through the stalk switch on the lower left side of the steering wheel. To adjust the target cruising speed, push the stalk switch upward and hold it, and the vehicle will accelerate automatically. Release the switch immediately when the desired speed is reached; pushing the stalk switch downward will decelerate the vehicle. Additionally, you can gradually increase or decrease the set speed by flicking the stalk switch and releasing it immediately. Each flick of the stalk switch will increase or decrease the speed by approximately 1 km/h. While the cruise control system is active, pressing the accelerator pedal normally can still accelerate the vehicle. Upon releasing the accelerator pedal, the speed will return to the set cruising speed. 2. The cruise system will automatically exit to standby mode under the following conditions: the stalk switch is moved to the "Cancel" position; the brake pedal is pressed; the gear of an automatic transmission model is shifted to P, R, or N; poor road conditions trigger the dynamic stability control system for safety reasons; or when the slope is too steep, causing excessive speed reduction, the cruise system will also pause automatically.

13

5

Share

What car brand is the slanted V?

What to Do When the Mercedes-Benz AC Blows Hot Air Instead of Cold?

How to Replace the Roof Lining of a 2010 Octavia?

What Gear Should an Automatic Transmission Car Be in When Warming Up?

What are the starting procedures for the BYD Han?

What to Do When Honda Car CAN Communication Fails?

How to Use the Cruise Control on MG6?

What to Do When Porsche Bluetooth Audio Is Not Working?

How to turn off the automatic steering wheel adjustment in BMW?

What procedures are required for transferring to another driving school?

How to Fix Electric Mirror Adjustment Failure?