···
Log in / Register

What are the reasons for the weak acceleration of Geely Vision?

3 Answers
DelJuliana
09/06/25 8:44am
Geely Vision's weak acceleration may be caused by insufficient power. Reasons for weak acceleration: Due to the blockage of the fuel tank cap vent, fuel tank switch, fuel filter, or the fuel line between the fuel tank and the carburetor, the required fuel supply cannot be met, resulting in an overly lean air-fuel mixture and weak engine performance. Long-term use of the air filter without timely cleaning can cause blockage, leading to insufficient air intake and an overly rich air-fuel mixture, which reduces engine power. Incorrect ignition timing or premature ignition can cause early combustion and detonation of the air-fuel mixture. Solutions: Check if the air filter is clogged and clean it if necessary. Check the throttle opening. When the accelerator pedal is fully pressed, the throttle should be fully open. Otherwise, adjust its cable or perform learning for the pedal position sensor and throttle position sensor. Check the high-voltage wires, spark plugs, and whether the high-voltage spark is too weak.
Was this review help?
9
1
Share
NaomiLynn
09/18/25 8:17am
I previously drove a Geely Vision and also experienced lack of power during acceleration. That time on the highway, pressing the gas pedal felt like the engine was weak and sluggish. After inspection, it turned out the fuel injectors were clogged, probably due to using low-quality gasoline. Also, worn-out spark plugs can cause poor ignition and sluggish acceleration. Carbon buildup in the throttle body is another common issue - over time it can block air intake, preventing proper combustion. My advice: don't skimp on fuel quality, use reputable gas stations, and replace spark plugs every 20,000 km or so. Cleaning the throttle body is DIY-friendly - just remove the intake pipe and spray with cleaner. Letting these issues persist can hurt fuel efficiency, wasting gas and compromising safety. Get your car's ECU trouble codes checked promptly at a repair shop before minor issues become major problems.
Was this review help?
10
2
Share
Expand All
CassidyFitz
11/01/25 8:44am
Lack of acceleration is quite common in Geely Vision models, often related to the engine system. Fuel system issues like insufficient fuel pump pressure or clogged injectors can prevent proper gasoline delivery. Worn spark plugs or faulty ignition coils in the ignition system lead to incomplete combustion. Restricted airflow from a dirty air filter is also frequent - replacing it only costs a few dozen yuan. I've seen many cars with clogged catalytic converters causing exhaust backpressure and sluggish acceleration. Faulty ECU sensors sending incorrect signals can disrupt fuel control too. Start with simple checks: test fuel pressure and try replacing spark plugs first. If that doesn't work, visit a dealership to scan for ECU trouble codes. Avoid unnecessary part replacements - repair when possible to save money.
Was this review help?
19
3
Share
Expand All
More Forum Discussions

What is the wheelbase of the Geely Panda?

The wheelbase of the Geely Panda is 2340 mm. This is a micro car, with dimensions of 3640 mm in length, 1630 mm in width, and 1465 mm in height. The Geely Panda is a safety-focused compact car and the first model under the Geely Gleagle brand, designed to meet four-star safety standards. The design of the Panda incorporates elements inspired by the national treasure, the giant panda. It features Geely's new logo and a four-door design, catering to domestic consumer preferences. In terms of body size, the Panda offers decent interior space, with a 205-liter trunk space that is very suitable for family use. The Panda is equipped with either a 1.0L or 1.3L engine, delivering a power output of up to 63 kW, which provides relatively high performance for a micro car.
4
2
Share

What is the correct way to start a car with one-button start?

The correct way to start a car with one-button start is: 1. Press the start button once to turn on the ACC light, then press the one-button start key while stepping on the brake to ignite and start the engine; 2. Release the foot brake, and you can choose to warm up the car in place, with the duration depending on the environment; 3. Step on the brake again, shift to D gear, release the handbrake, slowly release the foot brake, and gently press the accelerator to complete the one-button start process. The one-button start device is part of a smart car, serving as a button mechanism that simplifies the starting process and can also be used to turn off the engine. This device can be retrofitted in place of the original car key lock or installed as an independent panel.
5
3
Share

What Does Compression Ignition Engine Mean?

Compression ignition engine refers to an engine that does not rely on spark plugs to ignite the combustible mixture in the cylinder, but instead uses the high temperature and pressure at the end of the compression stroke to ignite the combustible mixture. All diesel engines are compression ignition engines. Among gasoline engines, only Mazda has developed a compression ignition engine. Compression ignition engines have higher compression ratios, stronger power, and higher efficiency. The Mazda 3 (Axela) is equipped with a compression ignition engine. Its 2.0-liter naturally aspirated compression ignition engine delivers 180 horsepower and a maximum torque of 230 Nm, reaching peak power at 6,000 rpm and maximum torque at 4,000 rpm. It features a 24V mild hybrid system, direct fuel injection technology, and an aluminum alloy cylinder head and block.
12
4
Share

What is the general size of a vehicle certificate of conformity?

The general size of a certificate of conformity is 4CM in length and 3CM in width. Here is the relevant information: 1. Introduction to the certificate of conformity: The certificate of conformity is an important document for a vehicle and is a mandatory document when registering the vehicle. Only vehicles with a certificate of conformity meet the national requirements for motor vehicle equipment quality and related standards. The vehicle registration documents will be filed with the vehicle management office. 2. Additional information: The vehicle certificate of conformity can be used to verify whether the vehicle matches its nameplate, check the engine number, chassis number, product certificate of conformity, manufacturing date, and other unique legal identifiers of the vehicle. It helps to determine the manufacturing date and identify if the vehicle is overstocked. It also provides information on the time from production to sale. The numbers on the certificate of conformity must match the engine number and chassis number on the vehicle.
1
5
Share

How long can you drive after drinking half a bottle of beer?

It is best to drive 24 hours after drinking, otherwise it will be considered drunk driving if caught. The following is the relevant introduction: 1. Drunk driving: Drunk driving refers to the act of driving a motor vehicle while completely or partially losing personal will due to alcohol consumption. A blood alcohol content of more than 20 milligrams per 100 milliliters is considered drunk driving. A blood alcohol content of 80mg/100mL or higher is considered drunk driving. 2. Drunk driving: The stimulation of alcohol during drinking can make people excited, and they may drink too much without realizing it. When the alcohol concentration in the human blood reaches a certain level, the person's reaction and control abilities to the outside world will decline, and the ability to deal with emergencies will also decline. For drunk drivers, the higher the blood alcohol content, the greater the chance of a crash.
16
0
Share

How many months is considered as stock car for joint-venture vehicles?

Joint-venture vehicles exceeding three months are considered as stock cars. Potential issues with stock cars include: 1. Moisture damage and aging: After leaving the factory, various fluids, electronic components, batteries, rubber seals, and tires may suffer from moisture damage and aging due to prolonged storage without periodic inspection and maintenance; 2. Weather exposure: Only a very few dealers implement periodic inspection and maintenance measures, which actually don't cost much but consume manpower and time. Some 4S stores even park new cars in open-air garages, exposing them directly to scorching sun, wind, and rain; 3. Oil and power shortage: For stock cars stored for too long without proper warehouse management, the aging degree of electronic components and rubber products is basically undetectable without professional testing equipment. Many vehicles stored for too long also experience oil and power shortage issues.
8
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.