What are the reasons for the high fuel consumption of Dongfeng Tianlong?

Should the last high beam in Subject 3 lighting test be turned off?

After completing the Subject 3 simulated lighting test, there's no need to switch from high beam to low beam before turning off the lights - you can directly turn off the lighting system. Additional notes regarding high beam reset to low beam in Subject 3: 1. Before the official test begins, if you notice the high beam is on, reset it to low beam. 2. If the previous lighting command was high beam and the next requires high-low beam switching, you must first reset to low beam before performing the switching operation, ensuring it ends on low beam. 3. When the final lighting command is high beam and the system prompts "Turn off lights" upon test completion, simply turn off the lights directly without resetting to low beam.

8

0

Share

How Do Traffic Police Handle Seized Vehicles?

Traffic police directly impound seized vehicles, and if no action is taken within three months, the vehicles are directly scrapped. Below are specific details about seized vehicles: 1. Nature: Seized vehicles are those prohibited by the court from undergoing registration, modification, transfer, mortgage release, deregistration, or release from pledge due to economic debt disputes and other reasons. 2. Laws and Regulations: According to Order No. 124 of the Ministry of Public Security, it clearly stipulates the operations prohibited during the seizure period by the court, namely, registration, modification, transfer, mortgage release, deregistration, and pledge release are prohibited during the seizure; however, annual inspections, temporary license plates, and replacement of license certificates are not prohibited.

19

0

Share

What is the maximum distance allowed for driving in second gear during Subject 3 test?

Generally, the speed in second gear during Subject 3 test should not exceed 20 km/h, but there is no minimum speed limit. This means it's acceptable to neither press the clutch nor accelerator after shifting to second gear. However, it's important to note that there are distance restrictions for first and second gears during the Subject 3 examination. When shifting from second to third gear, the gear change should occur at approximately 21-22 km/h. Additional information: For C1 license Subject 3 test, vehicles typically start in first gear and can shift to second gear once moving, as there are specific distance limitations for first and second gear usage during the exam - exceeding these limits will result in test failure. When driving in second gear, shift to third gear when reaching 20 km/h, and shift to fourth gear when exceeding 30 km/h.

17

0

Share

Can You Still Drive When the Audi TPMS Light Comes On?

Audi TPMS light on indicates that the tire pressure of a certain tire may be too low or the sensor battery is insufficient. If the light comes on while driving, please stay calm, do not panic, immediately reduce the speed and avoid fast steering and sudden braking, then check the tire pressure. The following are the functions of the tire pressure monitoring system: 1. Prevent accidents: The tire pressure monitoring system is a type of active safety equipment. It can issue an alarm in time when there are dangerous signs in the tires, reminding the driver to take corresponding measures, thereby avoiding serious accidents. 2. Extend the service life of tires: With the tire pressure monitoring system, we can keep the tires working within the specified pressure and temperature range at any time, thereby reducing tire damage and extending the service life of tires. Data shows that when driving with insufficient tire pressure, when the tire pressure is 10% lower than the normal value, the tire life will be reduced by 15%. 3. Make driving more economical: When the tire pressure is too low, the contact area between the tire and the ground will increase, thereby increasing friction resistance. When the tire pressure is 30% lower than the standard value, fuel consumption will increase by 10%. 4. Reduce the wear of the suspension system: When the tire pressure is excessive, the shock absorption effect of the tire itself will be reduced, thereby increasing the burden on the vehicle's shock absorption system. Long-term use will cause great damage to the engine chassis and suspension system; if the tire pressure is uneven, it is easy to cause the brakes to deviate, thereby increasing the wear of the suspension system.

16

3

Share

What Causes the Jerking of CVT at Low Speeds?

CVT jerking at low speeds is caused by engine carbon buildup or spark plug failure. Here are the relevant explanations: 1. Engine carbon buildup: When carbon builds up in the vehicle's engine, it not only leads to reduced power and increased fuel consumption but also causes unstable idling, resulting in jerking during cold starts. Additionally, if the spark plugs' ignition efficiency declines, the combustion conditions in each cylinder will vary significantly, leading to engine vibration accompanied by noticeable jerking. 2. Spark plugs: This issue may also be caused by insufficient engine warm-up. When the engine is cold, the oil's fluidity is poor, preventing effective lubrication of the engine pistons, which results in severe jerking during operation. Once the engine temperature returns to normal, this phenomenon will disappear. If the engine continues to jerk when warm, it is necessary to promptly visit a repair shop for inspection and maintenance.

13

2

Share

Can You Step on the Accelerator When Passing Through a Traffic Light in Subject Three?

In the driving test Subject Three, stepping on the accelerator is necessary because the test includes operations such as the 100-meter gear shifting, which requires the examinee to proficiently control gear shifting and accelerate. Notes: 1. When shifting from first gear to second gear and from second gear to third gear, the clutch release should be slow, and the acceleration should also be gradual. 2. When shifting to fourth gear or fifth gear, the clutch release should be quick, and the accelerator should be pressed swiftly. 3. At turns and intersections, try to continue driving at first gear speed without stopping if possible. 4. Both 180° turns and parking starts require first gear. 5. When driving straight, the steering wheel rotation should not exceed 5°; make minor adjustments as needed. 6. At zebra crossings, check traffic on both sides. 7. When changing lanes, observe the traffic situation behind the lane.

7

0

Share

What are the reasons for the high fuel consumption of Dongfeng Tianlong?

Should the last high beam in Subject 3 lighting test be turned off?

How Do Traffic Police Handle Seized Vehicles?

What is the maximum distance allowed for driving in second gear during Subject 3 test?

Can You Still Drive When the Audi TPMS Light Comes On?

What Causes the Jerking of CVT at Low Speeds?

Can You Step on the Accelerator When Passing Through a Traffic Light in Subject Three?

Can Pregnant Women Take the Driver's License Test?

How to Apply for Driver's License Cancellation?

How Much Tax Do You Need to Pay for an Imported Car?

What causes the jerking sensation when shifting gears during Subject 3 driving test?