What are the reasons for the continuous beeping of the Hyundai ix35 reverse radar?

1 Answers
SanEmilia
07/29/25 6:59pm
Apart from normal response, there are four situations that may cause the vehicle's radar buzzer to give false alarms when the Hyundai ix35 reverse radar keeps beeping: Situation 1: The reverse radar probe is covered with something, blocking the signal; Solution: Check if there is any obstruction in the radar holes at the rear of the vehicle. Situation 2: The rear wiper water pipe is leaking or water has seeped into the reverse radar system; Solution: Seal the leak or replace the pipe, then drain the accumulated water from the radar system. Situation 3: The radar ultrasonic signal is faulty, causing false alarms; Solution: Restart the engine, drive the vehicle to an open area, and try reversing again to observe the effect. Situation 4: The reverse radar circuit is short-circuited or the radar module is faulty; Solution: Take the vehicle to a 4S shop or repair shop for inspection, check the circuit, or replace the radar module.
Was this review help?
6
0
Share
More Forum Discussions

How to Tell if a Spark Plug is Not Tightened Properly?

Signs that a spark plug is not tightened properly: 1. It can lead to decreased vehicle performance or even prevent the car from starting; 2. The driver may hear a hissing or leaking sound while driving; 3. When the spark plug is in normal condition, the engine runs smoothly with stable sound, providing strong power and minimal noise during driving. The function of a spark plug is to introduce the high-voltage electricity (over 10,000 volts) generated by the ignition coil into the engine cylinder, creating a spark between the electrodes to ignite the air-fuel mixture. Common types of spark plugs include resistor spark plugs, platinum spark plugs, and iridium spark plugs. The lifespan of a resistor spark plug is about 20,000 kilometers, a platinum spark plug lasts around 40,000 kilometers, and an iridium spark plug can last between 60,000 to 80,000 kilometers.
3
0
Share

What is the correct installation method for shock absorbers?

Drive the vehicle into the work area and park it correctly. Extend the lift support pads under the vehicle to ensure good contact between the support pads and the vehicle's body support points. Remove the rain guard and wipers, then take off the tire. Place the removed tire steadily on the ground with the outer side facing up, and put the tire bolts on the tool cart. Gradually remove the connecting rod bolts, brake fluid line bolts, and ABS sensor line bolts. After removing the bolts, organize them neatly on the tool cart. Install the new shock absorber assembly onto the steering knuckle assembly, then assemble both the shock absorber assembly and steering knuckle assembly back onto the vehicle.
1
5
Share

What is the difference between off-line parts and original parts?

The difference between off-line parts and original parts: 1. Different manufacturers: Off-line parts are accessories that come off the automobile assembly line; original parts are the accessories that come with the car itself. 2. Different manufacturer authorizations: Off-line parts are not authorized or certified by the automobile manufacturer; original parts are authorized and certified by the automobile manufacturer. Tips for identifying the quality of automobile parts: 1. Original parts usually have standardized packaging with clear and regular printing, while counterfeit products have rough and inferior packaging printing; 2. Some original parts are specified in a certain color, and parts in other colors are counterfeit; 3. Original parts are made of qualified materials according to design requirements, while counterfeit products mostly use cheap and inferior substitute materials; 4. Inferior products are prone to cracks, sand holes, slag inclusions, burrs, or bruises in appearance.
19
3
Share

How to Reset the Maintenance Light on a Zotye Car?

Zotye Car Maintenance Light Reset Method: Turn on the ignition switch, press and hold the reset button with one hand while turning off the ignition switch with the other hand. Wait until the clock and mileage on the dashboard completely disappear, then release the button. Press and hold the reset button again and turn the ignition switch back on. The Zotye car has a body length, width, and height of 5020mm, 1877mm, and 1469mm respectively, with a wheelbase of 3000mm. It is equipped with a Mitsubishi high-performance and mature technology engine, which delivers strong torque in both low and high-speed ranges while maintaining high stability, making it suitable for various road conditions. The emissions meet the National III standard.
15
1
Share

Is it necessary to service the car every 5,000 kilometers?

It is not mandatory to service the car every 5,000 kilometers. The frequency of car maintenance varies depending on the brand, model, and type of engine oil used. Generally, mineral oil should be replaced approximately every 5,000 kilometers or every six months; semi-synthetic oil should be replaced around every 7,500 kilometers or every nine months; and full-synthetic oil should be replaced every 10,000 kilometers or every year, whichever comes first. Car maintenance primarily includes servicing the engine system, transmission system, air conditioning system, etc., aiming to keep the car clean, maintain normal technical conditions, eliminate potential hazards, prevent faults, slow down the deterioration process, and extend the vehicle's lifespan.
13
3
Share

Is Pressing the Clutch the Same as Shifting to Neutral?

Pressing the clutch and shifting to neutral have the same effect in terms of disconnecting the driving wheels from the transmission. In neutral gear, the transmission is still connected to the engine via the clutch, which remains engaged. When in neutral, the engine's power has already reached the transmission, but the neutral position means the power hasn't been transmitted to the drive axle, and it's used when the vehicle is stationary. Pressing the clutch stops the engine's power from reaching the transmission, which is used during starting and gear shifting. Pressing the clutch cuts off the power between the engine and the transmission, disconnecting the transmission from the engine, while the driving wheels rotate by inertia, causing all the gears in the transmission to rotate together.
3
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.