What are the reasons for the Audi air conditioning control panel not lighting up?

Turn off the AC first or turn off the engine first?

Turn off the AC before turning off the engine. Here is relevant information:1. Reason for turning off the AC first: If you turn off the engine first and then turn off the AC, the next time you start the car, the engine will start with the AC running, which undoubtedly increases the engine's load. Besides increasing fuel consumption, it also causes damage to the engine itself.2. After the car has been exposed to the sun: When the car has been exposed to the sun, if the outside temperature is 35 degrees Celsius, the interior temperature can reach 65 degrees Celsius within 15 minutes, causing the concentration of toxic gases inside the car to be 5 to 7 times higher than usual. Therefore, you should open all four windows for ventilation, then start the engine and turn on the AC. After blowing out the hot air from the AC, turn on the AC cooling switch. After cooling for 1 minute, you can close the windows, effectively preventing the harmful gases inside the car from escaping.

10

5

Share

What are the body dimensions of the Porsche Cayenne?

The length, width, and height of the Porsche Cayenne are 4918mm/1983mm/1696mm, which are official data. The length of the Porsche Cayenne refers to the distance between two vertical planes perpendicular to the vehicle's longitudinal symmetry plane and touching the outermost protruding parts at the front and rear of the vehicle. The width refers to the distance between two planes parallel to the vehicle's longitudinal symmetry plane and touching the outermost rigid fixed protruding parts on both sides of the vehicle. The height refers to the distance between the highest point of the vehicle and the supporting plane of the vehicle. The twin-turbocharged engine of the Porsche Cayenne has a maximum power of 324kW and a maximum torque of 550Nm. The maximum power speed of this engine is 5700-6600 rpm, and the maximum torque speed is 1800-5500 rpm. It features direct fuel injection technology and uses an aluminum alloy cylinder head and block. This engine is paired with an automatic transmission (AT). There are national regulations regarding vehicle dimensions. According to the national standard "GB1589-89," the total width of a vehicle does not include side mirrors. The limitation on vehicle width is to provide sufficient lateral clearance for overtaking between adjacent lanes. This means that, under national standards, the significance of vehicle width data is to ensure enough space during overtaking, preventing accidents due to excessive width or situations where road markings are narrower than the vehicle's width. Additionally, national regulations stipulate that the total width of a vehicle must not exceed 2.5m to meet the requirements of public road usage.

3

Share

Should the left or right turn signal be used for a right-angle turn?

Most test centers assess left right-angle turns, so the left turn signal should be used. If it's a right right-angle turn, then the right turn signal should be used. Below is relevant information about right-angle turns: 1. Overview: The right-angle turn is an assessment point in Subject 2 of the driver's test, evaluating the driver's ability to correctly manipulate the steering and accurately judge the vehicle's inner and outer wheel differences when driving through sharp turns. 2. Deduction points: If the wheels touch the protruding point, it results in failure; each time the wheels touch the road edge line, 20 points are deducted; completing the task with the help of reversing results in a 10-point deduction; not using the turn signal or using it incorrectly results in a 10-point deduction.

4

Share

What are the reasons why the car cannot exceed 100 speed?

It may be due to carbon deposits in the vehicle's engine. Here is the relevant introduction about carbon deposits: 1. The first concept: refers to the carbon deposits in the engine, which are a kind of coking substance produced by the unsaturated olefins and colloids in the fuel under high temperature conditions during the engine's operation. 2. The second concept: refers to the carbon deposits in electrical discharge machining, which should be avoided as much as possible, especially in precision mold processing where it can have a fatal impact. 3. Extension: Performing necessary cleaning on the car's intake system is the most effective method to reduce carbon deposit formation. Therefore, car owners can perform necessary cleaning on the car's intake system at around 30,000 kilometers.

19

3

Share

What Causes High Fuel Tank Pressure?

High fuel tank pressure can be caused by a clogged carbon canister, a blocked fuel tank cap regulator valve, a damaged solenoid valve, or temperature rise. During driving, gasoline sloshes inside the tank, and as the temperature rises after driving, especially in high summer temperatures, the gasoline expands due to heat, significantly increasing the vapor pressure, leading to high fuel tank pressure. Below are the related explanations: 1. Temperature factor: High fuel tank pressure caused by temperature is a normal phenomenon. 2. Overfilling the tank: If the tank is overfilled during refueling, some fuel may evaporate into the carbon canister, forming particles inside it, which can clog the carbon canister and lead to increased pressure. 3. Damaged solenoid valve: If the solenoid valve is damaged, the engine's pipeline system cannot properly ventilate to form a circuit, preventing the release of fuel vapor from the fuel tank, thereby increasing internal pressure.

3

2

Share

Reasons for Lack of Power After Engine Overhaul

Here are the reasons for lack of power after engine overhaul: 1. Non-standard repair and assembly processes: For example, not using specialized tools when disassembling the crankcase, but instead using hammers to strike and screwdrivers to pry open the case, resulting in deep scratches or deformation on the crankcase mating surfaces, leading to crankcase air leaks; poor concentricity of the crankshaft after the left and right crankcases are joined, increased friction of moving parts, engine overheating, and reduced power performance. 2. Failure to inspect the engine's lubrication system after vehicle repair: The process of replacing the cylinder block and crankshaft requires cleaning the old cylinder gasket. If the cylinder gasket in the crankcase is not thoroughly cleaned, the oil passages can easily be blocked by debris such as gasket material and sealant, preventing the lubrication system from functioning properly.

7

5

Share

What are the reasons for the Audi air conditioning control panel not lighting up?

Turn off the AC first or turn off the engine first?

What are the body dimensions of the Porsche Cayenne?

Should the left or right turn signal be used for a right-angle turn?

What are the reasons why the car cannot exceed 100 speed?

What Causes High Fuel Tank Pressure?

Reasons for Lack of Power After Engine Overhaul

What Does 4S Store Car Maintenance Include?

Are Polarized Sunglasses Suitable for Driving?

What does fuel additive mean?

What are the effects of starting a car with the air conditioning on?