What are the penalties for transporting diesel?

Should Left-Turning Vehicles Yield to Straight-Going Vehicles?

Left-turning vehicles should yield to straight-going vehicles. The situation where straight-going vehicles yield to turning vehicles applies to secondary roads yielding to main roads: In urban areas, the traffic volume on main roads is relatively high. Generally, main roads have priority. Therefore, if the secondary road is a straight lane and the main road involves turning vehicles, vehicles on the secondary road should yield to turning vehicles on the main road. If an accident occurs due to the secondary road vehicle not yielding, the secondary road vehicle, even if going straight, will bear full responsibility. Intersections with yield signs: These signs are usually placed at the junctions between secondary roads and main roads. Their primary purpose is to remind secondary road vehicles to yield to turning vehicles on the main road. Yield signs are further divided into two types: stop signs and slow-down signs. If a driver encounters a yield sign at an intersection, they must observe the main road traffic and only proceed into the intersection after confirming it is safe.

18

2

Share

Will the Motor of a Four-Wheel Drive Vehicle Expire?

The motor of a four-wheel drive vehicle will be scrapped after exceeding its service life. Motor: The term "motor" is a transliteration of the English word "motor," referring to an electric motor or engine. Its working principle involves the rotation of energized coils in a magnetic field, which drives the starter rotor to rotate. The small gear on the rotor then drives the engine flywheel to rotate. This technology was first used in the automotive industry in 1912. Motor Structure: This component consists of an internal gear ring and a matching gear or rotor. The internal gear ring is fixed to the housing, and the oil entering from the oil port pushes the rotor to revolve around a central point. This slowly rotating rotor drives the output through a spline shaft, forming a cycloidal hydraulic motor.

7

4

Share

What is the firing order of a motorcycle inline four-cylinder engine?

Inline 4-cylinder engines have a firing order of: 1-4-2-3 or 1-3-4-2. Motorcycle Engine: A motorcycle engine is a mechanical device that converts the thermal energy generated by igniting the fuel-air mixture in the cylinders into mechanical energy, which is then transmitted through the crankshaft and drivetrain to the rear wheel, providing the driving force for the vehicle. Inline Four-Cylinder Engine: The inline four-cylinder is one of the cylinder arrangements in internal combustion engines, most commonly found in four-cylinder engines with displacements below 2.0 liters. Since the four cylinders are arranged in a straight line, it is also known as a straight-four engine.

1

Share

What could be the reason for a sudden slight popping sound from the engine?

Possible reasons for a sudden popping sound from the engine are as follows: Engine mount rubber aging or loosening: The engine mount rubber refers to the rubber blocks placed between the engine and the vehicle frame. Their purpose is to reduce vibrations and provide cushioning during engine operation, as well as to secure the engine in place. Once these rubber mounts age or loosen, the engine may start to shake, resulting in abnormal noises. Engine misfire noise: An engine misfire mainly refers to one or more cylinders not functioning properly. Common symptoms include: intermittent exhaust gas flow from the vehicle, noticeable shaking of the exhaust pipe, and a clear "popping" or thumping sound from the engine. This phenomenon is often closely related to ignition coil failure. "Piston slap" noise: Due to poor lubrication conditions, excessive wear of the piston and cylinder walls can cause the clearance between the piston and cylinder wall to exceed normal tolerance ranges. When the engine is running, the piston skirt impacts the cylinder wall, producing a clear "clanging" sound, which is usually more noticeable at idle or low speeds.

3

0

Share

Can You Drive with Water in the Chassis?

You should not drive with water in the chassis. Mold and corrosion in vent holes: There are many channels in a car, and once water enters, it is very difficult to clean, leading to mold and corrosion over time. Examples include the inner side of door panels, air conditioning ducts, and some structural cavities. Additionally, vent holes are present in areas like the crankcase and differential. Deterioration of lubricating grease: The lubricating grease in components such as the four-wheel bearings and half-shafts can quickly deteriorate when soaked in water. Long-term issues with electronic equipment: Electronic devices in the car, such as the electronic parking brake, audio system, and some sensors, can easily develop long-term problems if not repaired promptly after being soaked in water.

17

5

Share

Can Replacing Original High-End Wheels Pass the Annual Inspection?

Replacing original high-end wheels can pass the annual inspection. Requirements for registration: In principle, modifying wheels is not allowed, so modified wheels need to be registered. Before modification, you can consult the vehicle management office to understand the situation, otherwise it may not pass the annual inspection. Legal basis for wheel replacement: According to the "Motor Vehicle Registration Regulations," changing the body color, model, performance, purpose, and structure of a licensed motor vehicle, or replacing the frame, body, or engine, the owner must apply to the vehicle management office for a change of registration. If the replaced wheels are of the same size, the annual inspection can generally be passed, but the appearance should not change too much.

4

1

Share

What are the penalties for transporting diesel?

Should Left-Turning Vehicles Yield to Straight-Going Vehicles?

Will the Motor of a Four-Wheel Drive Vehicle Expire?

What is the firing order of a motorcycle inline four-cylinder engine?

What could be the reason for a sudden slight popping sound from the engine?

Can You Drive with Water in the Chassis?

Can Replacing Original High-End Wheels Pass the Annual Inspection?

How to Replace the Battery in a New BMW Car Key?

Is it necessary to apply a protective film on the side mirror housing?

What is the principle behind easier starting when opening the choke?

Why Does the Steering Wheel Become Heavy?