Should the Wrongly Mounted Tire Be Reversed Back?

1 Answers
BrantleyDella
07/30/25 4:18am
Tires that are mounted incorrectly need to be reversed back. Here is the relevant introduction about car tires: 1. Reasons why tires cannot be mounted in reverse: The main reason tires must be installed according to the specified direction is that the tread pattern design and its orientation have a front and rear directionality, which plays a key role in drainage, anti-slip, and other aspects during normal driving. 2. Wrongly mounted tires affect braking performance: Incorrect tire mounting can reduce the car's grip, create uneven resistance on both sides, thereby affecting braking performance, and also accelerate tire wear. This can easily lead to the car pulling to one side and unstable steering.
Was this review help?
20
3
Share
More Forum Discussions

How to drive when one side of the double yellow line is solid and the other is dashed?

Lane changes are allowed with dashed lines. Only the side with the dashed line can cross into the lane with the solid line, and the lane change must be completed within the dashed section. There is another type of line called longitudinal deceleration lines, which are commonly seen on overpasses, toll stations, and other places. Longitudinal deceleration lines also consist of one dashed and one solid line.
2
2
Share

How to Inspect a Repaired Accident Vehicle?

Request a written checklist and confirm the repair timeline with the repair shop. When picking up the vehicle, verify each item on the list to ensure the repairs were completed correctly. A clean exterior helps the owner spot issues during inspection. A reputable repair shop must deliver the vehicle in a spotless condition. More detailed and professional inspections are essential. This is the key focus when accepting a repaired accident vehicle—checking whether the repaired areas truly meet expectations. For some accident vehicle repairs, issues may only become apparent months later.
6
4
Share

What are the causes of engine misfire?

Common causes of engine misfire include damaged ignition coils, insufficient air flow, intake system leaks, improper fuel pressure, and dirty or clogged fuel injectors. Below are detailed explanations and their solutions: Damaged ignition coil: Due to poor contact or excessive resistance, the ignition coil of the corresponding cylinder may become damaged, easily leading to engine misfire. In this case, the ignition coil needs to be replaced. Insufficient air flow: The powertrain control module detects that the output of the mass air flow (MAF) sensor is lower than the normal air flow, causing the air-fuel mixture to become too lean, and the exhaust gas recirculation (EGR) valve to malfunction. Professional repair shop inspection is required. Intake system leak: Air leaking into the intake system bypasses the mass air flow sensor, causing the air-fuel mixture to become too lean. Check for disconnected or damaged vacuum hoses. Improper fuel pressure: Faulty fuel pump, clogged fuel filter, or malfunctioning fuel pressure regulator can lead to improper fuel pressure, resulting in an overly lean mixture. Replace the fuel pump. Dirty or clogged fuel injector: Causes poor fuel atomization; damaged O-ring on the fuel injector. Poor fuel injector control circuit can lead to prolonged fuel injection or no injection. Clean the dirty fuel injector.
2
3
Share

What is the penalty for a private 7-seater car carrying nine people?

7-seater car carrying nine people is considered overloading behavior. According to relevant laws and regulations, a fine will be imposed, and the driver's license will be deducted 6 points. The penalty depends on the specific situation, such as whether it is an overloaded passenger transport vehicle, other passenger vehicles, or a truck. Different vehicles have different penalties.
17
5
Share

What to Do If the Car Stalls During Hill Start in Subject 2 Driving Test?

Starting the car by releasing the clutch too quickly without finding the semi-engaged point can cause the car to stall. When the car stalls, you should quickly press the brake pedal firmly and shift to neutral. After the car stalls, you must complete the starting operation within 30 seconds; exceeding this time will result in a failed test. When starting the car, first release the clutch until the car shows obvious vibration, then hold the clutch steady and slowly release the brake to achieve a smooth start.
2
0
Share

How to Deal with Flooded Vehicles?

Open the drainage outlets at the bottom of the vehicle to drain all the accumulated water inside, then use large fans, hair dryers, or similar devices to dry components like the seat adjustment motors. After parking and draining the water, the vehicle owner should check the condition of the fluids in various systems. If foaming or turbidity is observed, they should be replaced promptly. After the car gets flooded, promptly dry the electrical components. If possible, use fans to dry the interior to prevent short circuits in the wiring.
10
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.