Reasons for Difficult Car Starting?

2 Answers
DeNova
07/25/25 9:40pm
Reasons and solutions for difficult car starting are as follows: 1. Use of inferior engine oil. During cold starts, factors such as cylinder pressure, engine speed, and temperature make it difficult to ignite inferior engine oil, preventing the car from starting. Solution: It is recommended to use the manufacturer-recommended engine oil or a higher-quality full synthetic oil. 2. Battery depletion. If the voltage during startup is below the minimum operating voltage of the car's computer, the engine control unit will not function, making it impossible to start the car. Solution: The battery should be recharged or replaced. 3. Starter relay sticking. No response during startup is caused by a sticking starter relay. Solution: Simply press the tail of the solenoid to force it forward, thereby connecting the starting circuit and allowing the engine to start. 4. Spark plug issues. The vehicle may not start due to faulty spark plugs or ignition modules, which prevent the spark plugs from igniting. Solution: It is recommended to replace the spark plugs.
Was this review help?
19
4
Share
RuthDella
08/11/25 10:20pm
I've also experienced difficulty starting my car, and there are several common reasons. First is the battery issue; if it's old or the temperature is low in winter, insufficient battery power can prevent the car from starting. Second, there might be a problem with the ignition system, such as worn-out spark plugs or carbon buildup, resulting in weak sparks during ignition. Another possibility is a malfunction in the fuel system, where the fuel pump isn't working or the filter is clogged, preventing fuel from reaching the engine. Lastly, the starter motor might be broken or the switch has poor contact, causing the car to make grinding noises but not move. Remember to turn off the lights when parking to save battery power, and regularly check the battery voltage and spark plugs. These small actions can help avoid breaking down on the road and save you from expensive repairs.
Was this review help?
19
0
Share
Expand All
More Forum Discussions

How to Check Vehicle Speed?

The actual speed is 3 to 4 kilometers per hour slower than the speed displayed on the dashboard. Open Baidu Maps on your phone, which can display some fixed speed detection points and the actual driving speed of the vehicle. Use professional automotive electronic speed measurement equipment.
14
1
Share

What to Do When the Electric Car Screen Stays On?

Turn the power on and then off, listen for a "beep" sound to deactivate the alarm; if you hear three "beep beep beep" sounds, repeat the process until you hear a single "beep" sound. When the display screen remains lit, it is often due to rain affecting it. First, deactivate the alarm, then visit an after-sales service station.
4
0
Share

What does the 'tripa' on the car dashboard mean?

Car dashboard 'tripa' represents the trip mileage, which can be used to record the kilometers traveled for each trip. The 'tripb' on the left of 'tripa' represents the total mileage of the vehicle. 'Tripab' specifically refers to the distance from point A to point B. When needed, you can reset the displayed number to zero when starting from point A, and the number displayed upon reaching point B will be the distance between the two points. Both can be set to clear at different times and under different timing conditions. The car dashboard is a device that reflects the working conditions of various vehicle systems. Common indicators include the fuel indicator, washer fluid indicator, electronic throttle indicator, front and rear fog light indicators, and warning lights. Different cars have different instrument panels, but conventional car dashboards generally include a speedometer, tachometer, oil pressure gauge, water temperature gauge, fuel gauge, and charging gauge.
3
1
Share

How to Remove the Rear Tire of a Scooter?

Remove the bracket of the right rear shock absorber. Some right shock absorbers may obstruct the removal of the rear wheel, so it's necessary to detach the right rear shock absorber. Step on the wrench After loosening the nut, gently tap and vibrate the rear axle with a hammer to loosen the splines between the rear wheel and the axle, then the rear wheel can be removed.
11
1
Share

Installation of Guide Rails and Lead Screws?

Remove burrs and debris, place the guide rail against the reference surface, and tighten the bolts. Ensure each bolt leaves a gap in the guide rail mounting hole for later adjustments. Use a torque wrench to gently secure the bolts, pressing the clamping blocks against the rails. After both guide rails are installed as described, use a dial indicator to check the parallelism between them. Once installation is complete, move the worktable to confirm if the resistance is normal.
19
2
Share

How to Ride a Regular Motorcycle?

Hold the clutch with your left hand, pull it all the way in until there is no gap between the clutch and the handlebar, then step on the motorcycle's gear shift lever. Slowly release the clutch while gradually twisting the throttle with your right hand, and the motorcycle will start moving.
6
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.