Must the driver's license be issued within 24 hours after passing Subject 4?

1 Answers
Briana
07/30/25 9:03am
This is not necessarily the case. You should consult the driving school where you registered, as some regions issue the license immediately after passing, while others may take 3-5 days. Here is some additional information: 1. Subject 4: Also known as the theoretical test or driver's theory exam, Subject 4 is part of the motor vehicle driver's license assessment. The Subject 3 test consists of two parts: the road test and an additional safety and civics knowledge test. Since this test is conducted after Subject 3, it is commonly referred to as Subject 4. 2. Notes: After receiving your driver's license, you are qualified to drive the corresponding vehicle type. Generally, you can start driving immediately, but for safety, it's advisable to practice on less crowded roads first and gradually move to busier areas once you're more familiar with driving.
Was this review help?
11
1
Share
More Forum Discussions

How to Remove Small Particles of Stone Paint from a Car?

It can be washed off with water. Alternatively, scrub with a 10% ammonia solution, then rinse with a dilute acetic acid solution, and finally rinse with clean water. You can moisten it with a 10% citric acid solution, leave it for an hour, and then rinse it thoroughly with clean water. First, repeatedly apply kerosene, then apply some dilute acetic acid, and finally wash with water to remove it. Sprinkle a few drops of alcohol on it, then rinse thoroughly with warm water and soap. Turpentine can be used to wipe it off, and new stains can be soaked in water and scrubbed.
2
2
Share

How to Use a Portable Car Air Pump?

Insert the rubber hose nozzle directly into the tire valve. When you hear the sound of air escaping from the tire, it indicates that air is flowing. Tighten the inflation knob. Connect the red clip to the positive terminal of the battery and the black clip to the negative terminal, or plug it directly into the cigarette lighter for power. Turn on the motor to start inflating. During inflation, the gauge needle will rise with the increasing air pressure. When the main needle reaches the appropriate tire pressure for your car, turn off the air pump switch and remove the plug and nozzle.
18
2
Share

How to Clean Tree Sap Dropped on a Car Parked Under a Tree?

First, rinse the area with tree sap using water to prevent paint scratches from sand particles during wiping; Place a towel over the sap-covered area, and once the sap melts, it can be wiped off; Apply white vinegar, soapy water, or an alcohol solvent to a cloth and wipe the sap-covered area. The sap will decompose quickly and can then be easily removed. You can purchase a bottle of "tar remover" from an automotive store. Regardless of the brand, just a few drops will quickly remove the tree sap.
12
5
Share

How to Adjust Scattered Headlight Beams to Focus

To adjust scattered headlight beams, use a screwdriver to turn the screw rod behind the lamp bracket until the beams are focused. Below are specific reasons why car headlights may scatter instead of focusing: 1. Improper bulb positioning: Scattered beams indicate the bulb isn't centered in the housing. First check if the headlight base is loose, then readjust the height. 2. LED light emission point mismatch: When an LED bulb's emission point doesn't align with the original reflector's design, it causes beam scattering. Adjust the bulb position to match the reflector's refraction direction for proper focus.
4
3
Share

How to Solve the Problem of Slow Acceleration and Lack of Power in BYD S7?

From the turbocharger body to the throttle body, all the turbo pipes and clamp connections are normal and not detached; the throttle body sealing gasket is also well-sealed and not detached. There is no obvious oil trace at the air intake, and the exhaust turbo has no significant clearance and is dry, indicating that the turbocharger itself is working normally; the air recirculation valve is also well-sealed. No abnormalities were found in the intake manifold or the hard pipe connecting the brake vacuum pump to the vacuum booster.
7
1
Share

What does a paint thickness gauge reading over 1000 indicate about the thickness?

A paint thickness gauge reading exceeding 1000 indicates that the vehicle has undergone body repair work, with the thickness surpassing 500 microns. Here's the relevant explanation: 1. Paint application values: If the paint thickness exceeds the original factory paint specifications, it signifies that the vehicle has been repainted. 2. Professional repair institutions: When a vehicle's body paint suffers damage, it's advisable to have it repaired at a 4S shop or professional paint repair facility. Unprofessional paint repair shops often lack complete equipment and skilled technicians, which can compromise the repair quality, potentially affecting the vehicle's resale value and aesthetic appearance.
4
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.