JMC Pickup Truck Suddenly Stalls and Fails to Start

1 Answers
MacEvelyn
07/25/25 1:21am
The main reason is the use of low-quality fuel (many gas stations sell impure fuel for excessive profits), leading to engine carbon buildup and stalling. Below is relevant information: 1. Pickup Truck Annual Inspection: The annual inspection items for pickup trucks vary based on different classifications such as passenger vehicles, cargo vehicles, trailers, three-wheeled vehicles, and motorcycles. Among these, pickup trucks fall under the category of small cargo vehicles, and their annual inspection includes 8 major categories with 50 detailed items, covering vehicle uniqueness checks, online queries, vehicle characteristic parameter checks, vehicle appearance checks, safety device checks, chassis dynamic inspections, vehicle chassis component checks, and instrument equipment inspections. 2. Required Documents: For annual vehicle inspections, owners must bring the vehicle's "Driving License," "Insurance Certificate," and the owner's original ID card. For initial inspections (including new vehicles and transferred vehicles), vehicles are inspected based on the "Motor Vehicle Registration Business Acceptance Certificate." For periodic inspections, vehicles can be inspected using the "Motor Vehicle Driving License," "Motor Vehicle Periodic Inspection Form" (which can be downloaded online), and the "Third-Party Liability Insurance Certificate (Policy)."
Was this review help?
11
4
Share
More Forum Discussions

What are the causes of torsional vibration and shaking in the driveshaft?

The causes of torsional vibration and shaking in the driveshaft include: bending deformation and eccentricity of the driveshaft; loss of balance in the driveshaft; detachment of balance plates on the driveshaft; wear of the universal joint (cross pin and needle bearings); loose connection bolts of the rear axle flange on the driveshaft, etc. Here are the detailed explanations: 1. When starting the car, if the body shakes accompanied by a "clunking" impact sound; and during driving, a periodic noise can be heard from the chassis, which becomes louder as the speed increases; in severe cases, the cab vibrates, and holding the steering wheel causes numbness in the hands, all of which are symptoms of driveshaft torsional vibration failure. 2. When the technical condition of the driveshaft is good, the amplitude of bending vibration is small, and the shaking and noise are not obvious. When its technical condition deteriorates, the amplitude of bending and torsional vibration increases, the vibration becomes intense, and may even cause body shaking, accompanied by noticeable periodic noise that intensifies with increasing speed. 3. Vibration during acceleration at speeds of 30~50 km/h is caused by an inappropriate angle between the driveshaft and the pinion gear axis in the rear axle. This can be mitigated by reinforcing the rear suspension with some form of overload auxiliary leaf spring to ensure the pinion gear and driveshaft operate at the correct angle. 4. Vibration during deceleration at speeds of 30~50 km/h is usually the opposite of the above, caused by an excessive angle between the pinion gear and the driveshaft axis. This vibration is more intense and is often due to sagging suspension components and front springs. If the vibration becomes more severe with increasing speed, it is due to unbalanced or poorly assembled transmission components, requiring a balance performance check.
1
5
Share

What does 'hold' mean on a car key?

There are two meanings for the 'hold' button on a car key: 1. The 'hold' button on a car key usually means long-press. Some keys have a trunk symbol printed on it, indicating that holding it down will open the trunk. This simplifies the process of opening the trunk after unlocking the car. 2. The 'hold' button on a car key also has another function: a remote engine start button. Within a certain distance, holding it for 2-3 seconds will automatically start the car. This feature is useful in winter and summer to adjust the interior temperature in advance. When using remote engine start, there's no need to worry about car theft, as the central locking system remains engaged. The remote control range is typically no less than 50 meters, allowing you to start the car remotely from home or work.
1
5
Share

How to reset the tire pressure light on MG ZS?

Turn on the instrument power and press and hold the reset button until the low tire pressure warning light turns off. If the alarm persists after completing the above steps, consider a possible tire pressure sensor malfunction. Press and hold the reset button again until the low tire pressure warning light flashes three times and then turns off. Adjust the tire pressure according to the vehicle's built-in tire pressure standards. Drive at 30KM/H for 15 minutes to complete the initialization and return to normal. The maximum inflation pressure of car tires should not exceed specifications.
17
2
Share

What to Do If You're Afraid to Drive After Getting Your License?

You can find someone with extensive driving experience to accompany you, which can provide some psychological comfort and make you feel more at ease. Many people are too nervous to drive on the road. In fact, as long as you adjust your mindset and relax, you can drive well. Find a quiet, less-traveled road or practice at night when there are fewer vehicles. Have someone accompany you and practice for a few days before driving on busier roads.
3
1
Share

Which Ferrari models are convertibles?

Ferrari currently offers only the following models as convertibles: SF90 Spider and Ferrari Portofino M. Portofino M: A new Prancing Horse 2+ GT Spider model based on the Portofino sports car. The letter "M" in the Ferrari Portofino M name comes from the Italian word "modificata," meaning "upgraded (Modified)." It features a new 8-speed transmission and a five-position Manettino control knob with "RACE" mode. Additionally, this model is equipped with a 3.9T V8 twin-turbocharged engine that delivers up to 620cv at 7500 rpm. SF90 Spider: Ferrari's first plug-in hybrid convertible sports car, featuring the latest Ferrari retractable hardtop design. The model comes with an advanced plug-in hybrid system, with a maximum total output of 1000cv. Its V8 turbocharged engine has been redesigned to produce a maximum output of 780cv. Furthermore, the car is equipped with three electric motors—two on the front axle and one on the rear axle—providing a combined output of 220cv.
9
0
Share

How to Repair a Damaged Bumper?

If the bumper is severely damaged, it is recommended to replace it directly. If the bumper is only cracked, the repair method is as follows: 1. First, open the hood and remove the bumper. 2. Align the crack on the bumper and secure it with transparent tape to prevent deformation of the crack edges during operation. 3. Plug in the prepared soldering iron and flip the bumper over to inspect the crack inside. Wait for the soldering iron to heat up, then use it to melt and fix the crack inside the bumper. Operate according to the direction of the crack. 4. Use a plastic welding gun (hot air gun) to weld along the crack with the prepared PP welding rod. 5. Remove the transparent tape used on the bumper crack and go over the crack with the soldering iron again. Then, use 400-grit coarse sandpaper to sand the areas treated with the soldering iron and those needing touch-up paint. After sanding smooth, apply putty and let it dry. 6. Use wet sandpaper, starting with coarse grit and then fine grit to achieve a smooth finish. Rinse clean, wipe dry with a clean cloth, and wait for it to dry completely before painting. 7. Before spraying, shake the spray paint evenly. Maintain a distance of about 20 cm from the surface to be sprayed. Do not spray directly to avoid uneven coverage. Maintain an angle and allow about 15 minutes between each spray, applying 5-6 coats in total. 8. Let it dry for a few hours, then reinstall the bumper front panel. This completes the crack repair.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.