Is the Gap Between Baojun Cars and Joint Venture Cars Significant?

1 Answers
DiCharlie
07/30/25 4:38am
Baojun cars and joint venture cars do not have a significant gap. Baojun's engine is a domestically developed engine by SAIC. Baojun's engine is researched and developed by SAIC and produced in Liuzhou, Guangxi. This engine is praised by consumers for its mature technology, durability, and reliability. It also features multi-point electronic fuel injection technology. There are two versions of this engine: a 1.5L naturally aspirated engine and a 1.5T turbocharged engine. Below is some relevant information about Baojun's engines: 1. 1.5L naturally aspirated engine: Maximum power is 77 kilowatts, maximum torque is 135 Newton-meters, peak power is achieved at 5600 RPM, and peak torque is produced between 3600 to 5200 RPM. It features an aluminum cylinder head and a cast iron cylinder block. 2. 1.5T turbocharged engine: This engine has a maximum power of 108 kilowatts, maximum torque of 250 Newton-meters, peak power is achieved at 5200 RPM, and peak torque is produced between 2200 to 3400 RPM. It also features an aluminum cylinder head and a cast iron cylinder block.
Was this review help?
15
3
Share
More Forum Discussions

How to Steer the Wheel for Right-side Parking?

When the right starting sensor line appears and aligns with the lower edge of the left rearview mirror, turn the steering wheel fully to the right. Observe the right rearview mirror. When the far-right line becomes visible and the distance between the car body and the parking corner is less than 30cm, turn the wheel back halfway. When the parking corner disappears below the lower edge of the right rearview mirror, continue turning the steering wheel fully to the right. Observe the right rearview mirror. When the parking line becomes parallel with the car body, quickly straighten the steering wheel and continuously adjust the car body. Maintain parallelism between the car body and the parking line. Stop when the front parking line appears in the left mirror position.
9
4
Share

Does frozen windshield washer fluid have any impact?

Frozen windshield washer fluid does have an impact. If the reservoir is full, the frozen fluid will expand in volume, which can easily cause the reservoir to crack. Additionally, freezing can affect the sealing ring of the reservoir or the washer pump. Selection of windshield washer fluid: When choosing windshield washer fluid, it's important to select one suitable for the local temperature. In winter, opt for an antifreeze-type windshield washer fluid to ensure it won't freeze and damage vehicle equipment even when the external temperature drops below -18 degrees Celsius. Solutions for frozen windshield washer fluid: If the fluid freezes while driving, quickly find a safe place to stop. Then, use hot water to clean the pipes and spray nozzles. If there's sunlight, parking in the sun can help thaw the fluid, which works in most cases.
10
2
Share

Can You Change Engine Oil Without Replacing the Oil Filter?

You cannot change engine oil without replacing the oil filter, and the reason is: if you don't replace the filter, the dirt in the oil filter will re-enter the oil circuit and affect the normal operation of the engine. The precautions for changing engine oil are: 1. Choose the right oil for your vehicle; 2. Change the oil as much as possible when the engine is warm, and drain the oil completely; 3. The oil filter must be replaced when changing the oil; 4. The amount of oil added should be appropriate, based on the oil dipstick; 5. After adding the oil, start the engine and check whether there is any leakage in each component. The steps for changing engine oil are: 1. Lift the vehicle with a jack, find the drain bolt and unscrew it to drain the oil; 2. After unscrewing the oil filter, place a container underneath; 3. Replace with a new oil filter and add new oil.
14
5
Share

How to Open and Replace the Battery in a Kia K5 Key Fob?

The method to open and replace the battery in a Kia K5 key fob is as follows: 1. Remove the key part; 2. Use a one-yuan coin to twist open the key fob along the groove; 3. Replace the old battery with a new one. Taking the 2020 Kia K5 as an example, it is a mid-size sedan with body dimensions of 4855mm in length, 1835mm in width, and 1475mm in height, and a fuel tank capacity of 70 liters. The 2020 Kia K5 is equipped with a 2.0L inline 4-cylinder naturally aspirated engine, delivering a maximum horsepower of 156PS, a maximum power of 115kW, a maximum torque of 189Nm, and is paired with a 6-speed automatic manual transmission.
20
2
Share

How many days can a new car be driven without a temporary license plate?

A new car cannot be driven without a temporary license plate. Driving without a license plate may result in the vehicle being impounded and fines. Relevant regulations: According to the relevant provisions of the Road Traffic Safety Law, if a motor vehicle is driven without displaying a license plate, the traffic management department of the public security organ shall detain the vehicle, notify the party to provide the corresponding license plate, and impose a fine and deduct 12 points in accordance with Article 90. Procedure for obtaining a temporary license plate: The owner only needs to bring their ID card, car purchase invoice, compulsory insurance policy (copy), the original vehicle factory certificate and a copy, then go to the vehicle management office window to apply for a temporary license plate, fill out the application form, submit the relevant materials, and after review, receive the temporary driving license.
7
0
Share

Is it necessary to depress the clutch when stalling the engine?

It is necessary to depress the clutch to avoid damage to mechanical components caused by excessive transmission load. Below is a detailed introduction about the automotive clutch: 1. Overview: The automotive clutch is located within the flywheel housing between the engine and the transmission, with the output shaft of the clutch serving as the input shaft of the transmission. During vehicle operation, the driver can depress or release the clutch pedal as needed to temporarily disconnect or gradually engage the engine with the transmission, thereby cutting off or transmitting the engine's power input to the transmission. 2. Principle: The driving and driven parts of the clutch utilize friction between contact surfaces, or use liquid as a transmission medium, or employ magnetic transmission (electromagnetic clutch) to transmit torque, allowing temporary separation and gradual engagement between the two parts while permitting mutual rotation during the transmission process.
14
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.