Is the Cullinan turbocharged?

Why does ETC always beep?

ETC always beeps because there is an issue with the ETC device. Normally, the sound only occurs when passing through an ETC lane on the highway for identification, and it doesn't beep continuously. If this situation occurs, it is necessary to go to a maintenance center to check what fault the ETC device has. ETC is the Electronic Toll Collection system, also known as the Automatic Road Payment System. It is a road toll method specifically designed for toll roads, commonly seen on highways, bridges or tunnels implementing toll policies, and some sections of urban centers to alleviate urban traffic congestion.

6

4

Share

Why is the Corolla reverse radar not beeping?

Corolla reverse radar not beeping is due to damage to the reverse radar module or buzzer. Here are the specific details about the reverse radar: 1. Function: When reversing, it informs the driver about surrounding obstacles through sound or more intuitive displays, alleviating the troubles caused by the driver's need to look around during parking, reversing, and starting the vehicle. It also helps eliminate blind spots and unclear vision defects, improving driving safety. 2. Blind spots: The reverse radar also has certain blind spots, including obstacles that are too low (below 10~15cm from the center of the probe), too thin obstacles (such as isolation piles, diagonal steel cables), and ditches.

15

2

Share

What engine does the Nissan 370Z use?

The Nissan 370Z is equipped with a 3.7L V6 engine, model VQ37VHR. This engine features natural aspiration, has 6 cylinders arranged in a V-formation, uses a DOHC valvetrain, reaches its maximum power at 7000 rpm, runs on 95-octane gasoline, and employs multi-point fuel injection. The Nissan 370Z is a sports car under the Nissan brand, with dimensions of 4250mm in length, 1845mm in width, and 1315mm in height, and a wheelbase of 2550mm. The Nissan 370Z utilizes more lightweight materials, which significantly reduce the vehicle's weight and enhance various performance aspects such as acceleration, braking, and cornering.

6

4

Share

What is the normal RPM for an automatic transmission?

For an automatic transmission, an RPM of around 1800 to 2000 is considered normal. However, the required speed varies depending on different road conditions, and so does the RPM. As long as the engine RPM does not enter the dangerous range, it is generally considered normal. However, it is important to ensure that the RPM matches the current gear position. Otherwise, driving at a low gear with high speed or a high gear with low speed can cause unnecessary damage to the vehicle. An automatic transmission typically refers to the car's automatic gear-shifting mechanism, where the control system of the automatic transmission selects the appropriate gear based on the engine's RPM and load during driving, replacing the driver's subjective judgment and gear-shifting operations. Common automatic transmission positions include Park (P), Reverse (R), Neutral (N), and Drive (D).

10

1

Share

Is a Cold Start RPM of 1500 Normal?

A cold start RPM of 1500 is normal. Here are the details about cold starts: 1. Start Method: A cold start refers to starting the engine after it has been off for a while, cooled down, and its temperature is significantly below the normal operating temperature, with the engine oil mostly settled. Generally, it can be measured by ambient temperature—when the engine cools down to below 40°C after being turned off, which usually takes about 2 hours, starting it again is considered a cold start. 2. Impact on the Vehicle: Cold starts are more damaging to the car than warm starts, with over 80% of engine wear occurring during the cold start phase. Cold starts are also harder and take longer to initiate compared to warm starts.

14

0

Share

Why Is There Oil in the Intake Manifold?

Reasons for oil in the intake manifold: 1. Due to the condensation of engine oil vapor when it cools down, a small amount is normal; 2. Failure of the oil-gas separator, solution: clean the oil-gas separator or immediately replace the valve cover; 3. Clogging of the exhaust gas recirculation valve in the valve cover, solution: replace the valve cover. The intake manifold distributes air, fuel mixture, or clean air as evenly as possible to each cylinder, so the length of the gas flow channels in the intake manifold should be as equal as possible. To reduce gas flow resistance and improve intake capacity, the inner walls of the intake manifold should be smooth.

1

4

Share

Is the Cullinan turbocharged?

Why does ETC always beep?

Why is the Corolla reverse radar not beeping?

What engine does the Nissan 370Z use?

What is the normal RPM for an automatic transmission?

Is a Cold Start RPM of 1500 Normal?

Why Is There Oil in the Intake Manifold?

How to Read the Water Temperature Gauge in a Car?

What Causes Loud Abnormal Engine Noises?

Can the car still be driven when the 'Service Tire Pressure Monitoring System' warning appears?

What brand is DoubleKing tires?