Is it okay to idle the car and turn on the heater without moving?

1 Answers
MacAlice
07/24/25 11:19pm
It is not advisable to idle the car and turn on the heater without moving, as it can easily produce carbon monoxide, which is harmful to human health. When the car is in motion, the carbon monoxide generated will decrease or dissipate with the rapid convection of air. However, when idling, even outdoors, if there is no wind, carbon monoxide can accumulate around the car. The longer the duration, the higher the concentration, and a significant amount of carbon monoxide outside the car may be inhaled inside, leading to carbon monoxide poisoning. The car heating system is one of the functions of the car air conditioning system, which serves to provide warmth inside the car, regulate temperature and humidity, and defrost, among others. It can be classified into water-based heating systems, air-based heating systems, independent combustion heating systems, and combined preheating heating systems.
Was this review help?
7
3
Share
More Forum Discussions

How to Repair a Damaged Bumper?

If the bumper is severely damaged, it is recommended to replace it directly. If the bumper is only cracked, the repair method is as follows: 1. First, open the hood and remove the bumper. 2. Align the crack on the bumper and secure it with transparent tape to prevent deformation of the crack edges during operation. 3. Plug in the prepared soldering iron and flip the bumper over to inspect the crack inside. Wait for the soldering iron to heat up, then use it to melt and fix the crack inside the bumper. Operate according to the direction of the crack. 4. Use a plastic welding gun (hot air gun) to weld along the crack with the prepared PP welding rod. 5. Remove the transparent tape used on the bumper crack and go over the crack with the soldering iron again. Then, use 400-grit coarse sandpaper to sand the areas treated with the soldering iron and those needing touch-up paint. After sanding smooth, apply putty and let it dry. 6. Use wet sandpaper, starting with coarse grit and then fine grit to achieve a smooth finish. Rinse clean, wipe dry with a clean cloth, and wait for it to dry completely before painting. 7. Before spraying, shake the spray paint evenly. Maintain a distance of about 20 cm from the surface to be sprayed. Do not spray directly to avoid uneven coverage. Maintain an angle and allow about 15 minutes between each spray, applying 5-6 coats in total. 8. Let it dry for a few hours, then reinstall the bumper front panel. This completes the crack repair.
12
2
Share

How to Calculate Engine Displacement?

Displacement = π × radius² × height 3.1416159 × piston radius (mm) × piston radius (mm) × stroke (mm) × number of cylinders. Cylinder displacement is only an approximate value and is generally higher than the labeled value. Bore refers to the diameter, and the unit is usually millimeters.
5
2
Share

How to Use the Car Tire Pressure Monitoring System?

Press and hold the setting button on the display for about 3 seconds until you hear a click, and the left front wheel will flash; at this time, bring the display close to the sensor, and the display will automatically receive the sensor's ID. After the display shows the identification, click OK to confirm; then press SET to proceed to other tires, approach the other sensors one by one, and debug them sequentially. Tire Pressure Monitoring: Tire pressure monitoring is the real-time automatic monitoring of tire pressure during car driving, and it alerts for tire leaks and low pressure to ensure driving safety. Direct Tire Pressure Monitoring: The direct tire pressure monitoring device uses pressure sensors installed in each tire to directly measure the tire pressure. It uses a wireless transmitter to send the pressure information from inside the tire to a central receiver module, which then displays the tire pressure data for each tire. When the tire pressure is too low or there is a leak, the system will automatically alert. Indirect Tire Pressure Monitoring: When the pressure of a tire decreases, the weight of the vehicle will cause the rolling radius of that wheel to become smaller, making it rotate faster than the other wheels. By comparing the rotational speed differences between the tires, the system monitors the tire pressure. The indirect tire pressure alert system actually relies on calculating the rolling radius of the tires to monitor the pressure. Introduction to the Tire Pressure Monitoring System (TPMS): It combines the advantages of the two systems mentioned above, equipping direct sensors in two diagonally opposite tires and a 4-wheel indirect system. Compared to using a full direct system, this composite system can reduce costs and overcome the defect of the indirect system not being able to detect when multiple tires have low pressure simultaneously. However, it still cannot provide real-time data of the actual pressure in all four tires like the direct system does.
12
2
Share

How to Fully Lower the Rear Window of a Passat?

Press the button to the first position and release it when the desired position is reached. Briefly press the switch to the second position to automatically open the window. Push the button upward to the first position and release it when the desired position is reached. Pull the button forcefully to the second position, and the window glass will automatically rise and close. Simply hold the unlock button on the key for about 3 seconds, and all four window glasses will synchronously lower.
9
2
Share

How to Legally Install a Tow Hook?

First, locate the position as indicated in the vehicle's user manual, which is typically covered by a round or square cap. Press repeatedly around the edges of the tow hook cover to find an angle to pry it open. Use a small stick with a diameter smaller than the tow hook cover, wrap it with a cloth, and gently poke around to open it. After connecting the tow hook, you also need to connect the electrical circuit. Once the towing vehicle and the towed vehicle are connected via the tow hook, attach the safety wire to the steel ring next to the tow hook.
12
4
Share

How to Use Turn Signals in a Manual Transmission Car?

When starting the vehicle, turn on the left turn signal. When parallel parking, turn on the right turn signal. At intersections and forks, turn on the left turn signal when turning left, and the right turn signal when turning right. When changing lanes to the left, turn on the left turn signal. When entering a roundabout, no turn signal is needed; when exiting a roundabout, turn on the right turn signal. When overtaking, first turn on the left turn signal, and after maintaining a necessary safe distance from the overtaken vehicle, turn on the right turn signal.
19
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.