···
Log in / Register

Is it normal for water to appear under the exhaust pipe after parking a car?

1Answers
RyderFitz
07/24/2025, 11:47:55 PM

It is normal for water to appear under the exhaust pipe after parking a car. This indicates that the gasoline has been completely burned inside the engine during the vehicle's operation. For water to drip from the exhaust pipe after parking, the following three conditions must be met: 1. The air-fuel mixture ratio is within the normal range. Whether the engine is fuel-injected or carbureted, a normal air-fuel mixture ratio means the vehicle's fuel supply system is functioning properly, and fuel consumption will be within the normal range. 2. The engine cylinder pressure is normal. Normal cylinder pressure indicates that there is no significant wear inside the engine cylinder, or the wear is negligible, and components such as the cylinder liner and sealing rings are intact. If the engine has severe internal wear, incomplete combustion of gasoline will occur, preventing water from dripping. 3. The exhaust temperature is normal. Generally, most of the heat generated by the engine remains in the cylinders, with only a small portion entering the exhaust pipe. In this case, the engine's power output is stable. If the exhaust pipe temperature is too high, the water vapor will evaporate.

Was this review help?
113
Share
More Q&A

Can You Start the Engine While Charging a Car?

You can start the engine while charging a car. The method for charging a car is as follows: 1. Turn off the engine; 2. Take out the positive and negative cables; 3. Remove the clips to open the battery protective cover, exposing the battery's positive and negative terminals; 4. Connect one end of a cable to the positive terminal of the dead battery and the other end to the positive terminal of the charged battery; 5. Take another cable, first connect it to the negative terminal of the charged battery, then connect the other end to the engine block or body of the dead vehicle, ensuring the negative is connected to the negative; 6. Start the charged car. The steps for starting the engine are: 1. Turn the key to the 'on' position and wait; 2. After the dashboard icons flash and go off, turn the key to the 'start' position to ignite.
116
Share

What is the method to reset the tire pressure warning light on the Emgrand?

The method to reset the tire pressure warning light on the Emgrand is: 1. Turn on the ignition and press the multifunction button on the left side of the steering wheel to bring up the menu interface on the instrument panel; 2. Select the maintenance option, find the tire inflation pressure, and press the car button; 3. Choose the tire pressure monitoring system and then click to store the tire pressure. Taking the 2020 Emgrand as an example, it belongs to the compact SUV category, with body dimensions of: length 4440mm, width 1833mm, height 1573mm, wheelbase 2700mm, front track 1556mm, rear track 1562mm, fuel tank capacity 55l, trunk capacity 1042l, and curb weight 1365kg.
119
Share

What does the car tire warning indicate?

Tire pressure issues require prompt adjustment. Below is relevant information about the Tire Pressure Monitoring System (TPMS): 1. Introduction: The Tire Pressure Monitoring System is abbreviated as "TPMS". 2. Types: One is the indirect TPMS, which detects tire abnormalities through differences in tire rotation speed; the other is the direct TPMS, which involves installing four tire pressure monitoring sensors inside the tires. This system automatically monitors tire pressure and temperature in real-time, whether the vehicle is stationary or in motion, and provides timely alerts for high pressure, low pressure, or high temperature to prevent traffic accidents caused by tire failures, ensuring driving safety.
109
Share

Is Tesla Sunroof Detachment a Common Issue?

No, it's just an isolated case. For sunroof sunshade detachment repairs, visit a repair shop. Below is some information regarding vehicle damage assessment: Assessment Time: For damages occurring locally, the vehicle damage assessment can be completed within one working day by the local insurance company. For damages occurring in other locations, it takes one to three working days to complete the vehicle damage assessment. After the assessment, you can consult the local repair shop for the repair time. Note: The insurance company does not cover loss of income; it is recommended to negotiate a settlement as there are no clear legal stipulations. Survey and Damage Assessment: Surveyors must complete on-site inspection and assessment within one working day after receiving notification from the insurance company's internal staff (for damages occurring in other locations, the local insurance company can be entrusted to complete the inspection within three working days). Customers are required to provide relevant documents and guided to fill out the necessary claim forms.
109
Share

How to Turn on the Heater in a Mercedes-Benz GLC?

Mercedes-Benz GLC's air conditioning controls follow the conventional habits of fuel-powered vehicle air conditioning systems. There are two methods to turn on the heater. 1. Maintain the air conditioning in internal circulation mode to allow the engine to warm up quickly. After the engine has warmed up for 5-10 minutes, simply turn on the AUTO switch of the air conditioning, turn off the AC switch on the air conditioning control panel, and then adjust the preset temperature up or down using the temperature switches on both sides of the air conditioning panel. 2. Keep the air conditioning in internal circulation mode to let the engine warm up quickly. After the engine has warmed up for 5-10 minutes, adjust the preset temperature up or down using the temperature adjustment switch, ensuring it is higher than the current cabin temperature. Then, directly push up the third small fan button on the left side of the air conditioning panel to adjust the airflow, and finally turn off the AC switch to ensure the AC light is off.
107
Share

Where to Find the Engine Number on a POLO?

POLO's engine number is located on the side wall of the engine block, specifically on the side wall of the block below the exhaust manifold of cylinder 1. Open the hood, and you will see the engine number printed on a sticker on the left side of the engine. The engine number is also displayed on the firewall's nameplate. If there is dust or dirt on the engine, it is recommended to clean it first. The engine number consists of the following parts: 1. Prefix: Represents the product series and generation symbols, indicated by letters chosen by the manufacturer as needed, subject to approval by relevant authorities. 2. Middle section: Composed of symbols for the number of cylinders, cylinder arrangement, and cylinder diameter. 3. Suffix: Represents structural and usage characteristics, denoted by letters. 4. Tail: Distinguishing symbols. When differentiation is required due to improvements or other reasons within the same series, the manufacturer selects appropriate symbols for identification.
114
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.