Is it necessary to replace the battery at a 4S shop?

1 Answers
StWalker
07/30/25 12:40am
It is not necessary to replace the battery at a 4S shop; you can replace it yourself or have it replaced at an auto repair shop. Batteries generally need to be replaced every 2 to 3 years. The warranty period for a new car is usually 3 years or over 100,000 kilometers, and the lifespan of a car battery is approximately 3 years. After this period, car owners should pay special attention to the maintenance of the battery and replace it promptly when necessary to avoid potential hazards. If the battery is used frequently, subjected to heavy loads, or used extensively during this period, its lifespan may be even shorter. To extend the battery's lifespan, regular maintenance is required, along with good driving habits. When the electrolyte level is insufficient, it can cause the battery to lose charge, so it should be replenished promptly.
Was this review help?
8
5
Share
More Forum Discussions

What to Do When the Car Battery Has Power but the Engine Won't Start?

There are five possible reasons why a car battery has power but the engine won't start: 1. The gear is in D (Drive) position: Most car models are factory-set to prevent ignition if the gear is not in P (Park) position, primarily for safety reasons. This prevents the car from lurching forward if the gear is in D or R (Reverse) when starting. Solution: Shift the gear to P position and restart. 2. Steering wheel lock: This is an anti-theft feature. If the steering wheel is turned after the engine is off, the car's computer assumes a theft attempt and activates the anti-theft system. In this case, not only will the engine not start, but the steering wheel will also be locked. Solution: Turn the steering wheel while turning the key to start the engine. 3. Faulty fuel pump: This prevents fuel from being pumped. Solution: Replace the fuel pump. 4. Severe carbon buildup in the throttle body: This restricts the throttle opening, preventing the air-fuel mixture from entering the cylinders for combustion. Solution: Clean the carbon deposits from the throttle body. 5. Insufficient voltage to start the engine: A battery with power doesn't necessarily have enough voltage to start the engine. Over time, battery aging can reduce voltage, making it insufficient to power the starter motor. Solution: Replace the battery.
5
5
Share

Can You Still Drive When Prompted That the Engine Coolant Is Too Low?

Prompted that the engine coolant is too low, you should not continue driving. If the water temperature light on the dashboard comes on, you need to add antifreeze in time; otherwise, the engine may be damaged. Below is relevant information about antifreeze: 1. The main functions of antifreeze: (1) It provides anti-corrosion protection for components of the cooling system. (2) It prevents scale and reduces the temperature of the radiator. (3) It ensures the engine operates within the normal temperature range. Therefore, when antifreeze is insufficient, it directly affects the heat dissipation efficiency of the radiator. When the water temperature is too high, the red water temperature light on the dashboard will illuminate. If you continue driving without turning off the engine at this time, it may cause engine cylinder scuffing and damage. 2. Antifreeze replacement cycle: The antifreeze replacement cycle should be based on the manufacturer's manual, typically every 2 years or 40,000 kilometers, with the longest interval being every 4 years or 60,000 kilometers. A few car manufacturers support lifetime antifreeze that does not require replacement, only regular inspections. Since this type of antifreeze has slightly poorer fluidity, attention should be paid to whether the cooling system's circulation and heat dissipation are normal. Usually, you need to monitor the antifreeze level to ensure it stays between the minimum and maximum values.
8
1
Share

How to Open the Hood of a Leiling Car?

Method to open the hood of a Leiling car: There is a release handle under the dashboard on the driver's left calf side towards the front of the car. Pulling this handle will cause the hood to pop up about 1cm, and then you can lift the hood with some force. Below is an introduction to the functions of the hood: 1. Airflow guidance. For objects moving at high speed in the air, the air resistance and turbulence generated around the object directly affect its trajectory and speed. The shape of the hood can effectively adjust the direction of airflow relative to the car's movement and the resistance it generates, reducing the impact of airflow on the car. By guiding the airflow, air resistance can be decomposed into beneficial forces, increasing the force of the front tires on the ground, which helps stabilize the car's movement. 2. Protection of the engine and surrounding pipeline components. Under the hood are critical components of the car, including the engine, electrical circuits, fuel lines, braking system, and transmission system, all of which are vital to the vehicle. By enhancing the strength and structure of the hood, it can effectively prevent adverse effects such as impact, corrosion, rain, and electrical interference, ensuring the normal operation of the vehicle. 3. Aesthetics. The exterior design of a vehicle is a direct reflection of its value. As an important part of the overall appearance, the hood plays a crucial role in being visually pleasing and embodying the concept of the entire car.
13
0
Share

What Causes the Abnormal Noise in the Clutch Spring of a Car?

Possible reasons for abnormal noise in the clutch spring of a car include: insufficient lubricant in the release bearing; no clearance between the release bearing and the inner end of the release lever; severe oil contamination or dust accumulation between the release bearing sleeve and the guide tube; excessive looseness in the spline hole of the driven plate and its spline shaft; annealing fatigue or breakage of the driven plate damping spring; loose rivets or exposed rivet heads on the driven plate friction disc; and excessive wear in the drive pins of a double-disc clutch and the pin holes in the intermediate pressure plate and pressure plate. The diagnostic and troubleshooting methods for abnormal noise in the clutch spring are as follows: 1. Slightly depress the clutch pedal to make the release bearing contact the release lever. If a 'rustling' sound is heard, it indicates abnormal noise from the bearing. If the noise persists after lubrication, it means the bearing is excessively worn or damaged and should be replaced. 2. Depress and release the clutch pedal. If intermittent collision sounds occur, it indicates axial movement of the release bearing, and the return spring of the release bearing should be replaced. 3. Continuously depress the pedal. If noise occurs when the clutch is just engaged or disengaged, it indicates loose or exposed rivets on the driven plate, and the driven plate should be replaced.
14
1
Share

Where to Add Coolant for the Verna?

Coolant for the Verna needs to be added to the reservoir located on the left side of the engine. The coolant replacement method is as follows: Before completely replacing the coolant, conduct a thorough inspection to check for any signs of leakage or cracks in the pipes, with a special focus on the five-way hose. The coolant flows through the five-way hose before being distributed to different parts of the car to function. If there is any leakage of coolant in this section, replace the hose or resecure the connection as needed. Drain the old coolant, then flush the liquid channels with clean water. Add clean water to the coolant reservoir, then continue filling the reservoir with water to allow it to circulate continuously through the engine cooling system. Start the engine and let it idle for 3 to 5 minutes to circulate the water. The water initially draining from the reservoir may appear slightly pinkish. Continue adding clean water until the drained water runs clear. Note: Remember to disconnect the heater hose and drain the water from the heater core. After draining for about an hour, add the new coolant through the radiator hose. Then, add another bottle of coolant to the reservoir until it is nearly full. Start the engine and let it run for about 10 minutes. As the cooling system expels some air, the coolant level will drop. Top up the coolant to the "MAXT" mark on the reservoir.
18
1
Share

Where is the unlock button in a BMW?

BMW's unlock button is located at the top center of the dashboard, below the hazard lights, and is shaped like a key. There are three methods to unlock a BMW door: 1. Proper use of the transmitter on the key: When the key is within the unlocking distance, the car will automatically unlock; conversely, when the key is beyond this distance, the car will lock, eliminating the need for manual button pressing. 2. BMW doors are equipped with automatic locking systems, all controlled electronically. 3. If the key is damaged, you can use a tool: A wire or a makeshift key can also unlock the door, but this method should only be used as a last resort.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.