Is it necessary to arrive on time for Subject 4?

1 Answers
MacEden
07/24/25 6:12pm
You can arrive a bit late, but it is recommended to be on time. Additional information: Exam basics: The Subject 4 exam lasts 45 minutes, consists of 50 questions, with a full score of 100 and a passing score of 90. It includes true/false questions, single-choice questions, and multiple-choice questions. The main content assessed includes: safe and civilized driving operation requirements, safe driving knowledge under adverse weather and complex road conditions, emergency handling methods for situations such as tire blowouts, and knowledge of post-accident procedures. After passing Subject 4, candidates must undergo at least 30 minutes of traffic safety and civilized driving education, including case studies of traffic accidents, followed by a swearing-in ceremony. Only then will the vehicle management office issue the driver's license. If it cannot be issued on the same day, it will be mailed to the driving school where the student is enrolled, and the school will notify the student to collect it, or it will be sent to the address provided by the student.
Was this review help?
12
4
Share
More Forum Discussions

What to Do When the Envision's Battery Dies?

Here are the solutions for when the Envision's battery dies: 1. Push-starting is the most effective emergency starting method, but it is a last resort and should not be used frequently. This method can cause some damage to the engine and clutch, especially in automatic transmission vehicles, which should avoid using this method to start. 2. To avoid being unable to charge when the battery dies, the owner should prepare a set of jumper cables in the car, which can be purchased at most auto parts stores. However, when connecting the jumper cables, it is crucial not to mix up the connection sequence. First, connect the positive terminal of the dead battery to the positive terminal of the rescue vehicle's battery. Then, connect the negative terminal of the rescue vehicle's battery to a metal part (ground) in the engine compartment of the dead car. After connecting the jumper cables, start the rescue vehicle's engine and slightly increase the engine speed. After about 5 minutes, the dead battery can be emergency charged. Once charging is complete, remove the jumper cables in the reverse order of connection. 3. The lifespan of a battery is generally 2 to 3 years. Beyond this period, the owner should pay special attention to the battery's maintenance and replace it promptly if necessary to avoid potential hazards.
12
5
Share

How to Adjust the Time on an Older Chevrolet Model?

Click on the settings icon on the display screen. Select and click on the date and time option, then click on set time. Use the plus and minus signs on the display screen to set the new time, then click on set date on the display screen to complete the process.
1
4
Share

How to activate the Leiling Lane Keeping System?

Pull up the intelligent driving control interface on the audio-visual system display. Touch the "Lane Keeping Assist" button to turn the lane keeping assist function on or off. The system only activates when the vehicle speed is within the range of 60-140 km/h.
6
4
Share

How to Set Lexus Seat Memory?

Adjust the seat position and height according to your needs. After adjusting the seat, press the SET button located at the lower left side of the seat. The SET button will turn red, indicating that the system is memorizing the seat position. Finally, press either 1 or 2 to set the memory button.
10
3
Share

What are the reasons for severe shaking in a three-cylinder engine?

The reasons for severe shaking in a three-cylinder engine are as follows: 1. Dirty air filter: The air filter is designed to protect the engine and reduce wear. It is generally replaced every 10,000 kilometers. If not replaced in time, insufficient air intake can cause low idle speed, leading to engine shaking. 2. Spark plug lifespan: Spark plugs have a limited lifespan. After exceeding 30,000 to 40,000 kilometers, their ignition efficiency significantly decreases, which can affect ignition. Low idle speed: The engine's idle speed is preset in the computer. When the RPM drops below a certain range, the car's computer will automatically adjust it. 3. Abnormal water temperature: The engine operates within a normal temperature range. High water temperature can cause early ignition timing, changes in the air-fuel mixture, thinning of engine oil viscosity, and reduced lubrication performance. Common causes of shaking include insufficient coolant, a stuck thermostat, a non-functioning fan, or inaccurate temperature control switch settings. 4. Clogged fuel injectors: The fuel injectors in fuel-injected cars are critical components for fuel delivery and have a long lifespan, often reaching hundreds of thousands of kilometers. However, deposits in gasoline can clog the injector nozzles, causing inconsistent fuel delivery among injectors and uneven cylinder operation, leading to engine shaking. 5. Carbon deposits and oil sludge blockages: Over time, carbon deposits and oil sludge can accumulate in the throttle body, idle valve, and intake ports, obstructing airflow and affecting idle stability, resulting in shaking.
18
3
Share

Does the Toyota Vios have an anti-collision beam?

Toyota Vios is equipped with an anti-collision steel beam. The anti-collision steel beam is a U-shaped channel formed by stamping cold-rolled steel plates, connected to the frame longitudinal beams, serving as the first barrier of passive safety for the vehicle. It is an important safety device that absorbs and mitigates external impact forces, protecting the front and rear parts of the vehicle body. Below is relevant information about the anti-collision steel beam: 1. The ends of the Vios' anti-collision beam are connected to low-speed energy absorption boxes with very low yield strength, which are then bolted to the vehicle's longitudinal beams. These low-speed energy absorption boxes can effectively absorb collision energy during low-speed impacts, minimizing damage to the vehicle's longitudinal beams, thereby reducing repair costs. The bolted connection allows for easier replacement of the anti-collision beam. 2. In high-speed offset collisions, the anti-collision beam can effectively transfer the impact force from the left (or right) side of the vehicle to the right (or left) side, allowing the entire vehicle body to absorb the collision energy as much as possible. During low-speed collisions (generally below 15km/h), the anti-collision beam can prevent damage to the front and rear longitudinal beams of the vehicle body, reducing repair costs.
9
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.