Is a fuel consumption of 13.6 considered high?

2 Answers
VonEmiliano
07/28/25 11:26pm
Strictly speaking, a fuel consumption of 13.6L/100km is relatively high. Here are some methods to reduce fuel consumption: Start smoothly: The first thing everyone should do is to start the car smoothly. Many drivers pursue aggressive driving and rapid acceleration starts. Every time they stop at a traffic light, they are the first to rush out, which might look impressive on the surface. However, this kind of operation will increase fuel consumption. Everyone should aim for a smooth yet quick start to reduce the engine's warm-up time and improve fuel efficiency. Avoid frequent sudden braking: Of course, this situation is the most common driving habit among many novice drivers. Due to insufficient driving skills, they tend to slam on the brakes suddenly in emergencies, causing the vehicle to stop abruptly. If the brakes are applied this way every time, it will not only increase fuel consumption but also potentially lead to rear-end collisions from vehicles behind.
Was this review help?
10
2
Share
AddysonLynn
08/12/25 3:48am
As a seasoned driver with over a decade of experience, I must say that a fuel consumption of 13.6 isn't particularly high, but it depends on what you're driving. For large SUVs or pickup trucks in urban conditions, this level is quite common due to their heavy weight and large engines. However, for compact sedans, it would be on the higher side, where normal consumption might range between 7-10. My own mid-size SUV averages close to 12, and frequent traffic jams can cause it to spike. Fuel efficiency also heavily depends on driving habits: gentle acceleration and avoiding sudden braking can save a significant amount on gas. For older vehicles, engine carbon buildup or underinflated tires can easily increase consumption; regular maintenance like oil and filter changes can bring it down below 11. In summary, 13.6 is reasonable in most cases, but if you're driving a compact car, it might be high, and it's worth checking your vehicle's condition to protect your wallet.
Was this review help?
13
1
Share
Expand All
More Forum Discussions

What to do if the driver's license expires within one year?

If the driver's license has been expired for less than 12 months, you can proceed with the renewal as usual. When the driver's license expires, you should go to the vehicle management office to apply for a replacement. You need to bring the identity proof of the vehicle owner and standard photos of the vehicle, etc. If the driver's license has expired, it is as if you do not have a driver's license, and the vehicle cannot be driven on the road. If caught by traffic police, the owner will be detained. In insurance contracts, a vehicle with an expired driver's license is considered unqualified. If a vehicle insurance accident occurs, no claims will be paid.
12
4
Share

How to Test the Engine Oil Level Sensor?

Disconnect the wiring harness plug of the engine oil pressure sensor and remove the sensor. Screw the hose connector of the oil pressure gauge into the threaded hole of the oil pressure sensor. Place the oil pressure gauge in a location where it will not come into contact with rotating or high-temperature engine components. Start the engine and check for any oil leaks at the oil pressure gauge connection. If leaks are found, turn off the engine and retighten the connection. Run the engine until it reaches normal operating temperature, then check the oil pressure gauge readings at both idle and 2000 r/min.
19
2
Share

How to Remove and Replace the Low Beam Headlight of the New Sylphy?

Open the engine compartment cover, locate the rear cover of the headlight at the headlight position, unplug the connector, and unscrew the bulb. More related information is as follows: 1. The low beam headlight is designed for close-range illumination, with a large coverage area (160°) and a short illumination distance, and the focus cannot be adjusted. The low beam must be turned on in the following situations: driving in areas without streetlights at night, driving at dusk when it is relatively dark or at dawn when the light is just appearing; if encountering heavy fog, snow, or heavy rain that obstructs visibility, the low beam must be turned on even during the day; on some roads where there are lighting facilities but the brightness is insufficient, the low beam should also be turned on. 2. Although the low beam has an illumination distance of about 30 meters, it has a very noticeable beam cutoff line. Most car low beams have an illumination distance of 30-40 meters, with the beam cutoff line at about 12-18 meters. The area in front of the beam cutoff line is brightly lit, allowing clear identification of objects, and a clearly visible illuminated area of 2-3 meters in diameter can be seen on the ground. The area from behind the beam cutoff line to 30-40 meters mainly relies on ground-reflected light sources. In this area, brightly colored objects can be distinguished, but dark-colored stationary objects on the road are not easily noticeable.
5
4
Share

How to Remove the Gear Knob of Geely Borui?

Most manual transmission gear knobs are screwed on, and there may be one or two fixing screws. Remove the fixing screws and rotate the gear knob counterclockwise to take it off. Some models have gear knobs connected with dust boots. In this case, you need to loosen the dust boot first and pry it out with a trim panel tool. Since the replacement here is not an original gear knob, you need to install the included fixing bolt. Put the fixing bolt on the gear lever and tighten it clockwise. Finally, screw the new gear knob on.
1
0
Share

How many engine models does the Audi Q5L have?

The Audi Q5L has only one engine model, which is the EA888 2.0T. There are 5 methods for car engine maintenance: 1. Clean the air filter: If the air filter is clogged or accumulates too much dust, it can cause poor engine intake. A large amount of dust entering the cylinder will accelerate carbon buildup, leading to poor engine ignition, insufficient power, and increased fuel consumption. 2. Remove throttle valve sludge: This is caused by carbon deposits from fuel combustion exhaust at the throttle valve and residues of impurities not filtered by the air filter. 3. Clean injector carbon deposits: The combustion chamber is prone to carbon buildup, which can also cause difficulty in starting. Carbon deposits in the injector can block the fuel passage, distort fuel injection, and impair atomization, leading to increased fuel consumption. 4. Regularly clean the fuel system: During the combustion process in the combustion chamber, gum and carbon deposits form and accumulate in the fuel passages, carburetor, injector, and combustion chamber, interfering with fuel flow, disrupting the normal air-fuel ratio, and causing poor fuel atomization, which can lead to engine stuttering and other faults. 5. Choose the appropriate quality grade of engine oil: Based on the working principles and usage conditions of the intake and exhaust systems, select the suitable engine oil.
9
2
Share

How to Reset the Tesla Tire Pressure Light?

Tesla tire pressure light reset steps: Turn the ignition switch to the second gear, and the instrument panel will display the total mileage/trip mileage interface. Press the "OK" button on the left side of the steering wheel, then press the right button to enter the "Maintenance" interface. Press the down arrow button on the steering wheel to enter the "Tire Pressure" interface. The instrument panel will prompt "Run-Flat Indicator Activated," press the "OK" button on the steering wheel to confirm. The instrument panel will prompt "Is the tire pressure normal?" Use the down button on the steering wheel to select "Yes" and press "OK" to confirm. What to do if the tire pressure is insufficient: If there is no visible damage to the car's tires, you can simply inflate them to the normal tire pressure and then reset the tire pressure system. If a puncture is found during inspection, drive to a car repair shop promptly to have the tire repaired, then reinflate it. If the tire pressure warning appears again after inflation but there is no puncture, it may be due to air leakage caused by a deformed wheel rim. It is recommended to check the wheel rim and replace it if necessary. The working principle of the tire pressure monitoring system is: It uses pressure sensors installed inside the tires to measure the tire pressure and wireless transmitters to send the pressure information from inside the tire to a central receiver module.
17
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.