Introduction to Chery Arrizo GX?

Where is the VIN number located on a Land Rover Range Rover?

The VIN number stamping on a Land Rover Range Rover is located near the top of the right front suspension strut tower, which can be found by opening the engine hood. Additionally, there is another VIN number at the lower left corner of the windshield, though this one is not stamped. The Range Rover is equipped with three types of engines: a low-power version 3.0-liter twin-turbocharged engine, a high-power version 3.0-liter twin-turbocharged engine, and a 5.0-liter V8 supercharged engine. The dimensions of the Land Rover Range Rover are 5000 mm in length, 2073 mm in width, and 1869 mm in height, with a wheelbase of 2922 mm. The front suspension type is a double-wishbone independent suspension, the rear suspension type is a multi-link independent suspension, and the body structure is unibody.

13

4

Share

What maintenance is required for the BMW 5 Series' third service?

BMW 5 Series' third service requires oil change, three filters replacement, brake fluid replacement, and some routine inspections. The specific maintenance items for the third service and minor maintenance items are as follows: Third service items: The third service is a major maintenance, typically performed every 10,000 kilometers. It includes oil change, oil filter replacement, air filter replacement, cabin air filter replacement, fuel filter replacement, engine internal carbon deposit cleaning, fuel system carbon deposit cleaning, throttle carbon deposit cleaning, transmission fluid replacement, differential oil replacement, brake fluid replacement, coolant replacement, spark plug replacement, paint surface care, interior cleaning and disinfection, and engine exterior cleaning. Definition of minor maintenance: Minor maintenance generally refers to the routine maintenance items performed at the manufacturer-specified time or mileage to ensure vehicle performance after the car has traveled a certain distance. It mainly includes oil change and oil filter replacement.

2

3

Share

What is the situation when the EPC light comes on and then goes off after restarting?

epc light comes on and then goes off after restarting is a normal phenomenon. The fault light comes on after the ignition switch is turned on, but the system has no fault after the car is started, and the light will go off. In the EPC system, the previous throttle cable is canceled and replaced by a sensor of the pedal device. The engine control unit calculates the optimal target throttle opening based on the position data fed back by the pedal device sensor and sends a signal to the throttle drive motor to rotate the throttle to this angle. Precautions for using the EPC system: 1. This method is better than the cable-type acceleration control, because the electronic throttle calculates and analyzes the input signal from the accelerator pedal position to know the engine's power demand and converts this information into the engine's torque through various actuators. 2. Due to safety and fuel consumption reasons, when the engine speed needs to be adjusted, the engine control unit can adjust the throttle position without passing through the accelerator pedal. The advantage of this structure is that the control unit can limit the throttle position according to various needs.

4

5

Share

What are the body dimensions of the Changan CS75?

The length, width, and height of the Changan CS75 are 4650mm, 1850mm, and 1705mm respectively, with a wheelbase of 2700mm. Relevant information is as follows: 1. The interior space is very spacious: when the front seats are adjusted to the foremost position, there is still a four-finger distance from the head, and the legroom is also comfortable. With the front seats unchanged, there is a distance of one fist and four fingers in the legroom, and a four-finger distance from the head. 2. There are four models of the Changan CS75: the 2017, 2018, 2019, and 2020 versions, divided into National V and National VI emission standards. 3. The Changan CS75 is positioned as a compact SUV, available in both two-wheel drive and four-wheel drive versions. The four-wheel drive version adopts a front-engine, four-wheel drive layout with an on-demand four-wheel drive system, and the central differential uses a multi-plate clutch.

17

2

Share

Where is BMW produced?

Domestically produced BMW models, such as the 3 Series and 5 Series, are manufactured by the joint venture BMW Brilliance in Shenyang. Imported BMWs are produced at BMW's overseas plants, primarily in Bavaria, Germany. Here is more information about BMW: 1. BMW's model series include 1, 2, 3, 4, 5, 6, 7, i, M, X, Z, and others. 2. Among them, the 1 Series is a compact car, the 2 Series is a small coupe, the 3 Series is a mid-size car, the 4 Series is a mid-size coupe (including convertibles), the 5 Series is a full-size car, the 6 Series is a full-size coupe (including convertibles), the 7 Series is a luxury D-segment car, the i Series represents BMW's electric and hybrid vehicles, the M Series is BMW's high-performance and sports car version, the X Series is BMW's specific SUV lineup, and the Z Series is BMW's entry-level sports car.

19

4

Share

Why Don't Concept Cars Go into Mass Production?

Concept cars are not mass-produced for the following reasons: 1. High production costs: Butterfly doors, oversized rims, fully touch-sensitive dashboards, color-changing sunroof glass, foldable and rotatable seats, and other high-tech features would significantly increase production costs if implemented. 2. Difficulty passing tests: Many eye-catching concept cars are designed for display purposes only and lack practical functionality. Transitioning from a concept car to a mass-produced vehicle requires aerodynamic and gravitational force validation. Experts explain that concept car designs often haven't undergone wind resistance testing. If directly applied to production models, the immediate consequence would be poor fuel efficiency. For example, their unconventional, attention-grabbing rims also require durability and wind resistance verification. Before a new car hits the market, rigorous crash tests are necessary to assess safety. The exaggerated designs of concept cars—such as avant-garde flat bodies or oversized glass panels—could compromise structural rigidity in critical areas. 3. Showcasing brand philosophy: Automakers introduce concept cars primarily to convey their design philosophy. Often, these vehicles are never actually produced. By showcasing perfect craftsmanship, manufacturers create positive impressions among consumers, enhancing brand image.

13

4

Share

Introduction to Chery Arrizo GX?

Where is the VIN number located on a Land Rover Range Rover?

What maintenance is required for the BMW 5 Series' third service?

What is the situation when the EPC light comes on and then goes off after restarting?

What are the body dimensions of the Changan CS75?

Where is BMW produced?

Why Don't Concept Cars Go into Mass Production?

How to Check the Order Progress After Booking a Tesla?

Why Can't the Volkswagen Magotan Key Be Pulled Out?

How to restart the Audi MMI system?

What aspects should be paid attention to when buying a car in installments?