How to Use the Electronic Gear Lever on the Boyue?

1 Answers
LaCarlos
07/25/25 12:12am
For the Geely Boyue, pushing the electronic gear lever downward engages Drive (D) mode for forward movement, pushing it upward engages Neutral (N), and pushing it further up engages Reverse (R). Moving it to the left activates Manual (M) mode, while the P button is for Parking. Below is relevant information: 1. The Geely Boyue PRO is equipped with two turbocharged engines: 1.8TD and 1.5TD. The 1.8TD engine has been widely used in several Geely models and was awarded the "China Heart" Top 10 Engines in 2016. 2. The third-generation 1.8TD turbocharged engine featured in the Boyue PRO has been recalibrated for superior performance, delivering a maximum power of 135 kW (184 Ps) and a peak torque increased by 15 N·m to 300 N·m compared to the previous generation, with a combined fuel consumption of 7.5L per 100 km.
Was this review help?
19
2
Share
More Forum Discussions

How to Replace the Rear Brake Pads of Honda XR-V?

Method for replacing the rear brake pads of Honda XR-V: 1. The rear wheel of Honda XR-V is equipped with an electronic parking brake motor. First, connect the computer to the vehicle; 2. On the brake pad replacement setting interface, select 'Open the rear wheel brake caliper'; 3. The caliper disengages, and the brake motor retracts; 4. Then loosen the two nuts of the cover, lift the outer cover of the brake caliper, and install the new brake pads; 5. After installation, use the computer again to set 'Close the rear wheel brake caliper'. The following is an introduction to brake pads: 1. Brake pads are generally composed of steel plates, adhesive heat insulation layers, and friction blocks. The heat insulation layer is made of non-heat-conducting materials to insulate heat. 2. The friction block is composed of friction materials and adhesives. When braking, it is squeezed against the brake disc or brake drum to generate friction, thereby achieving the purpose of vehicle deceleration and braking.
11
2
Share

What is the keyless start tutorial for Chery eQ1?

Chery eQ1 keyless start steps are as follows: 1. First, press the foot brake and press the start-stop button to ignite the car. 2. Release the foot brake to warm up the car in place, then press the foot brake and release the handbrake. 3. Shift the gear from P to D to achieve keyless start. Here is an introduction to the keyless start system: The keyless start system (Keyless-Start-System) allows you to start the vehicle without taking out or turning the key. Simply keep the key in your bag or pocket, press the button inside the car or turn the guide plate to ignite the engine. It is more convenient and enhances the sense of luxury and technology.
8
2
Share

How to Fold Down the Rear Seats in the Octavia?

Method to fold down the rear seats in the ŠKODA Octavia: 1. Move the front seats forward and retract the rear seat armrest. 2. Stow the center rear seat's safety belt buckle and adjust the headrest to its lowest position. 3. Pull the seat folding switch located on the shoulder of the rear seat to fold it down. Related information on different rear seat folding methods: 1. Split-folding rear seats refer to the backrests being foldable in a certain ratio, offering higher flexibility compared to a full folding mechanism. This allows for folding down only half of the backrest to accommodate large items while the remaining part can still seat passengers. 2. Full folding rear seats mean the backrest folds as a single unit, providing more space when transporting large objects. The downside is that the rear seats cannot accommodate passengers when folded down.
11
1
Share

What to Do When the Reversing Camera of Volkswagen CC Fails to Display?

Solutions for the Volkswagen CC reversing camera not displaying: 1. If the host's connector is loose, the camera and screen cannot properly match and connect, so the reversing camera will not display. In this case, simply remove the host and reinsert the connector properly. 2. There are many reasons for camera failure, including water ingress, short circuits, burnt connecting wires, etc. In such cases, it is necessary to go to a repair shop or 4S store for professional inspection and repair, and replace the camera if necessary. 3. There are also many reasons for display screen failure, requiring professional inspection and repair at a repair shop or 4S store. 4. When the camera is blocked, the captured image cannot be displayed normally. In this case, simply clean the camera in time. 5. If the car's gear is not in reverse, the reversing camera function will not be activated. Therefore, simply shift the gear into reverse. The body dimensions of the Volkswagen CC are 4862mm in length, 1870mm in width, and 1447mm in height, with a wheelbase of 2841mm.
19
2
Share

How to Turn Off the Auto Start-Stop Function on Buick Excelle?

The method to turn off the auto start-stop function on Buick Excelle is as follows: 1. The start-stop function switch is located next to the ignition switch or on the center console panel. After the engine starts, the auto start-stop system will be enabled. 2. By pressing the button, the auto start-stop system can be manually deactivated. The principle of auto start-stop is as follows: 1. The start-stop system works when the vehicle stops moving due to traffic congestion or at an intersection. The driver presses the brake pedal and shifts to neutral. The Start/Stop system automatically detects: the engine is idling and no gear is engaged; the wheel speed sensors of the anti-lock system show zero; the electronic battery sensor indicates there is enough energy for the next start. 2. When these three conditions are met, the engine automatically stops. When the traffic light turns green, the driver presses the clutch, and the 'start-stop device' can be activated immediately, quickly starting the engine. In automatic transmission models, as soon as the brake is released or the steering wheel is turned, the engine automatically restarts, allowing the driver to press the accelerator and start moving immediately, all while remaining in D gear.
13
1
Share

How to Adjust the Clock in Magotan?

Here are the steps to adjust the time in Magotan: 1. Press the one-touch start button on the vehicle's center console to power on the instrument panel; otherwise, time adjustment is not possible. 2. Press the SET button on the left side of the steering wheel. 3. Use the up and down option toggle buttons on the right side of the steering wheel to adjust the vehicle's time. 4. Press the OK button on the steering wheel to confirm the adjustments. 5. Check the instrument panel to ensure the time is displayed correctly. Introduction to the Volkswagen Magotan: 1. Design: The Magotan features groundbreaking avant-garde design, interpreting fashion aesthetics with grandeur, perfectly blending design aesthetics with luxury quality. 2. Technology: The Magotan is equipped with a series of high-end intelligent technologies surpassing its class, such as the FPK digital LCD instrument panel, third-generation ACC advanced adaptive cruise control, and a 360-degree panoramic parking system—many of which are high-end technologies typically found in C-class cars, setting new trends in intelligent driving. 3. Powertrain: The entire lineup comes standard with engine start-stop and SSR 2.0 second-generation brake energy recovery technology. The powertrain has been fully upgraded, perfectly balancing performance and fuel efficiency, pushing energy conservation and environmental protection to the forefront. The new-generation Magotan, equipped with the advanced second-generation DCC dynamic chassis system for the first time, allows drivers to switch between comfort, standard, and sport modes, achieving a seamless transition between driving pleasure and comfort.
15
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.