How to Use the Cruise Control on Baojun 510?

How to Adjust the Hardness of the Cab's Shock Absorber Airbag?

The hardness of the cab's airbag is related to the material of the airbag and cannot be adjusted. Here is some relevant information about shock absorber airbags: 1. Introduction: Shock absorbers are vulnerable components during the use of a car. The performance of the shock absorber directly affects the smoothness of the car's ride and the lifespan of other components. Therefore, it is essential to keep the shock absorber in good working condition. 2. Development: After driving the car on a road with poor conditions for 10km and then stopping, touch the outer shell of the shock absorber with your hand. If it is not hot enough, it indicates that there is no resistance inside the shock absorber, and the shock absorber is not working. At this point, you can add an appropriate amount of lubricating oil and test again. If the outer shell becomes hot, it means there is insufficient oil inside the shock absorber, and more oil should be added. Otherwise, it indicates that the shock absorber has failed.

2

3

Share

Where is the cabin air filter located in the XC60?

The cabin air filter in the XC60 is located beneath the glove compartment on the passenger side. The steps to replace the XC60 cabin air filter are as follows: 1. Unscrew the two nuts under the glove compartment and lower the bottom panel; 2. Reach into the panel on the right side of the center console and gently remove the panel; 3. Lift the felt covering the center console, then remove the wiring harness box inside the glove compartment to access the XC60's cabin air filter. The XC60 is a mid-size SUV under the Volvo brand, with body dimensions of 4688mm in length, 1902mm in width, and 1658mm in height, and a wheelbase of 2865mm. In terms of power, the Volvo XC60 is equipped with a 2.0T engine. The T4 model uses a 2.0T engine coded B4204T31, with a maximum power output of 140kw, while the T5 model uses a 2.0T engine coded B4204T26, with a maximum power output of 184kw, both meeting the China VI emission standards.

7

4

Share

What Needs to Be Done for Used Car Refurbishment?

Clean the interior and exterior thoroughly before putting it up for sale. The following are precautions for used car transactions: 1. Verify the identity of the used car: When purchasing a car, carefully check the ID card, original vehicle invoice, vehicle purchase tax certificate, vehicle license, road maintenance fee certificate, annual inspection certificate, and insurance policy to ensure there are no issues. If the documents are incomplete, you may encounter numerous hassles when handling related procedures later. There have been precedents in this regard, so be extremely careful. Additionally, verify the engine number and chassis number to confirm the vehicle's identity and avoid being deceived. 2. Check if the odometer has been tampered with: To fetch a higher price, dealers often roll back the mileage. In reality, mileage is just one factor in assessing a car's condition. The actual condition can be determined by inspecting parts like the engine, and the odometer reading is not the sole determinant of the car's price. 3. Don’t overlook repainting: Check for any peeling paint, fresh marks on the surface, or excess paint around the exhaust pipe, trim, and windows. If found, it indicates the car has been refurbished, possibly due to scratches or damage, which can serve as one of the criteria to judge its condition.

8

3

Share

Can Accident Vehicles Be Insured?

Accident vehicles can indeed be insured. Here is relevant information about accident vehicles: Definition of an accident vehicle: First, observe whether the gaps between body panels are uniform and consistent, then check if the side body lines are smooth. If noticeable misalignment in the waistline is found, it can be concluded that the vehicle has been involved in a collision, and a relatively severe one at that. Hazards of accident vehicles: Vehicles involved in major accidents typically leave traces on the frame that are difficult to fully repair; once a severely damaged vehicle is flooded, its electrical circuits and components can suffer very serious damage.

4

1

Share

Is pressing the right corner during a right-angle turn due to turning the wheel too early or too late?

Pressing the line during a right-angle turn depends on the situation: 1. Taking a left turn as an example, if you turn the steering wheel too early before entering the right angle, the left wheel will press against the right angle. To avoid pressing the right angle, you must not turn the steering wheel all the way. Wait until the rear wheel passes the right angle before turning the steering wheel all the way. In this case, the right front wheel will definitely press against the right line after the turn; 2. Still taking a left turn as an example, if you are very close to the left line when turning, you must not turn the steering wheel too early. If you turn too early, the car will press against the right angle. If you turn too late, the situation mentioned in the question will occur. Therefore, for a left turn, you should stay closer to the right side; 3. Taking a left turn as an example, if you are not very close to the left line but are driving closer to the right side, turning the steering wheel too late will also cause the right line to be pressed after the turn.

1

4

Share

What are the symptoms of an air leak in a car engine?

An air leak in a car engine can result in increased exhaust emissions and reduced acceleration power. Here is additional information about engine air leaks: 1. Causes of air leaks: Clogged air filters or poor working conditions can allow sand, dust, and other particles to enter the valve guides, causing wear on the valve stems and guides. This leads to uneven wear between the valve heads and seats, compromising the seal and resulting in air leaks. Valve heads located in the upper part of the combustion chamber are constantly exposed to high-temperature, high-pressure gas, making them prone to erosion and leaks. Incorrect valve clearance adjustment, either too small or nonexistent, can cause the valve train components to expand when heated during operation. This may result in the rocker arm head pressing against the valve stem end, preventing the valve from closing properly and causing leaks. 2. Solutions: During maintenance, thoroughly clean carbon deposits in the cylinder, especially on the valve stems, valve seats, and seat openings. Carefully inspect the number of erosion spots and the width of the contact band on the valve cone surface. If the contact band is too wide or there are many erosion spots, use a reamer to adjust and lap the surface. If the valve seat ring is damaged, the valve head is warped, or the stem is bent, replace the valve or valve seat ring. If the issue is due to insufficient valve clearance, readjust the clearance to meet the required specifications.

20

3

Share

How to Use the Cruise Control on Baojun 510?

How to Adjust the Hardness of the Cab's Shock Absorber Airbag?

Where is the cabin air filter located in the XC60?

What Needs to Be Done for Used Car Refurbishment?

Can Accident Vehicles Be Insured?

Is pressing the right corner during a right-angle turn due to turning the wheel too early or too late?

What are the symptoms of an air leak in a car engine?

Should You Apply Brakes When Making a U-Turn in Subject 3?

What type of engine oil is suitable for the Kia K5?

What kind of shops can clean car chassis?

Which car brand does the MC logo belong to?