How to Use the Cruise Control in the 2021 Buick Excelle?

What is the difference between natural cracking and human-induced cracking of car glass?

Car glass natural cracking and human-induced cracking are distinguished as follows: Differences in fragment area: Human-induced cracks tend to produce larger fragments due to external force impact, whereas natural cracks result in smaller fragments caused by internal stress without external force impact. Differences in impact marks: Examine the fragments for impact marks - human-induced breakage will show obvious impact traces on the glass fragments, while spontaneous glass breakage leaves much smaller marks. Additionally, tempered glass doesn't completely shatter into individual pieces when broken; many fragments remain connected, making them easier to identify.

18

1

Share

How to Check Driver's License Status?

Driver's license status can be checked through the following methods: Online Vehicle Management Office Query: Visit the online vehicle management office for inquiry. Some cities have enabled this online query feature where personal information can be used to check driver's license status, which is quite convenient. City Services: Use the driver's license status query feature within city services. Some cities support this function, allowing you to locate your own city for a quick query. Inquiry Hotline: Many regional traffic police websites list a free traffic violation inquiry hotline that you can call to check your status. Alternatively, you can dial 114 for traffic violation inquiries. Vehicle Management Office: Bring your documents to the local vehicle management office for inquiry. It's advisable to check their working hours beforehand and visit at an appropriate time to inquire about your driver's license status.

18

0

Share

What are the four basic components of a friction plate clutch?

The friction plate clutch is basically composed of four parts: the driving part, the driven part, the pressing mechanism, and the operating mechanism. Below is a related introduction to the friction plate clutch: Function: The function of the clutch is to transmit and cut off power. It is required to smoothly complete power transmission during the car's starting process and quickly cut off power during gear shifting or braking. Additionally, the clutch has an additional function of preventing overload in the transmission system. Working Principle: The engine torque is transmitted to the driven plate through the friction between the flywheel and the driven plate contact surface, and then it is passed to the drive wheels through the driven shaft and a series of components in the transmission system. The greater the pressing force of the pressing spring, the greater the torque the clutch can transmit.

10

3

Share

What are the causes of clutch shudder?

Clutch shudder can be caused by the following reasons: Uneven distribution of normal pressure between the driving and driven discs: In a friction clutch, uneven spring tension of the pressure plate springs, inconsistent adjustment of the release levers, and/or uneven ends of the diaphragm spring fingers can lead to asynchronous engagement timing, uneven force distribution on the pressure plate, or even tilting of the pressure plate. This results in poor contact between the driving and driven discs, causing clutch shudder. Weakened damping spring tension: Weakened tension of the clutch torsional damping springs, reduced tension of the clutch pressure plate springs, or cracks in the diaphragm spring can all cause shudder during clutch engagement.

20

0

Share

What does the ABS warning light mean?

There are various conditions when the ABS light is on, with different causes and solutions for each condition, as detailed below: Condition 1: ABS warning light stays on (most common). Cause 1: The ABS wheel speed sensor's sensing part is covered by mud, sludge, or other contaminants, affecting its ability to detect the corresponding speed signal. This prevents the ABS control unit from determining the vehicle speed or wheel slip rate, thus failing to issue appropriate commands to regulate braking. Solution: Clean the dirt from the wheel speed sensor and adjust the gap between the sensor and the tone ring to restore normal function. Cause 2: Poor signal due to loose system wiring connections or poor contact in the ABS relay, leading to system malfunction. Solution: Inspect wiring connections and reconnect any loose parts. Condition 2: ABS warning light intermittently illuminates but turns off during acceleration. Cause: When multiple electrical devices are in use, battery voltage drops below 10.5V. As engine speed increases, voltage rises, and the ABS light turns off. This may also occur due to low system supply voltage, such as poor terminal contact or grounding issues. Solution: Check battery specific gravity; inspect the charging system; verify power supply (e.g., voltage relay or poor power contact). Condition 3: ABS warning light stays on after engine start but turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS control unit failure. Solution: Loosen and retighten the hydraulic valve body ground screw, cleaning the contact surface if necessary; check for enlarged connector gaps; replace the ABS or ABS/ASR control unit. Condition 4: ABS warning light illuminates during high-speed driving. Cause: The ABS control unit detects a significant discrepancy between rear and front wheel speeds; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, typically found on the label near the fuel filler cap. Condition 5: ABS warning light intermittently illuminates. Cause: Improperly adjusted brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal and push the brake switch linkage down fully with your finger, then release the pedal to complete self-positioning; replace the brake light switch if necessary. If the ABS warning light is on, it is recommended not to continue driving. An illuminated ABS light indicates a malfunction in the anti-lock braking system. During emergency braking, locked wheels may cause the vehicle to skid uncontrollably, preventing the driver from slowing down or adjusting the vehicle's path, posing significant safety risks.

6

1

Share

What is the minimum speed for fourth gear?

For manual transmission vehicles, the minimum speed for fourth gear is 40km/h. Below is a related introduction about vehicle gears: Speed aspects: First gear corresponds to a speed of 0-5km/h, second gear to 5-20km/h, third gear to 20-40km/h, fourth gear to 40-60km/h, and fifth gear to 60-100km/h. Shifting timing: The general shifting timing for most vehicles is when the engine reaches 2000r/min, and should not exceed 2500r/min. For some high-displacement, high-power engines, shifting can occur around 3000r/min.

15

0

Share

How to Use the Cruise Control in the 2021 Buick Excelle?

What is the difference between natural cracking and human-induced cracking of car glass?

How to Check Driver's License Status?

What are the four basic components of a friction plate clutch?

What are the causes of clutch shudder?

What does the ABS warning light mean?

What is the minimum speed for fourth gear?

What is the technical term for the handbrake?

How many models of Mercedes-Benz SUVs are there?

Does using fuel from small gas stations affect the car?

What does 'ch' mean on the dashboard?