How to update ETC after vehicle transfer?

Is It Normal for the Display Screen of Baojun 560 to Stay On After Turning Off the Engine?

It is not normal for the display screen of Baojun 560 to stay on after turning off the engine. Reasons for the screen staying on: There may be a short circuit in the wiring of the vehicle's navigation host or an issue with the program. Solutions: If the navigation screen remains on after turning off the engine, you will need to use a car diagnostic tool to access the SMK system and read the data stream. If the data stream shows that both "ACC" and "ACC input circuit and battery circuit (when the engine is off)" are in the ON state, it indicates a short circuit. The cause of the short circuit is likely a problem with the power supply module, and it is necessary to promptly inspect and repair the relay.

19

4

Share

What is the minimum ground clearance of the Tang?

The minimum ground clearance of the BYD Tang DM is 170mm. Measurement method: The body length is the distance between the two extreme points in the length direction of the car, that is, from the most protruding position of the front bumper to the most protruding position of the rear bumper; the body width is the distance between the two extreme points in the width direction of the car, which is the distance between the left and right most protruding positions of the body. According to industry standards, the body width does not include the width of the left and right rearview mirrors when folded. The body height is the distance from the ground to the highest point of the car, and the highest point refers to the highest position of the car's roof, excluding the length of the roof antenna. Related car dimensions: The dimensions of the Peugeot 308 are not much different from those of the 307. The body dimensions of the domestic Peugeot 308 are 4558mm, 1805mm, and 1505mm, with a wheelbase of 2612mm, slightly increased in length, width, and height compared to the 307.

3

4

Share

How many liters of oil can a BMW X1 hold?

The BMW X1 requires approximately 5L of oil for an oil change. The recommended oil type for the BMW X1 is 5W-30. If you are considering an oil change during later maintenance, you can choose from brands such as Shell, Mobil, or Castrol. The official manual recommends oil specifications of 0W30, 5W30, 5W-40, or 0W20. Oil viscosity changes with temperature, so it is important to pay special attention to its performance under both low and high temperatures. For example, in 5W-30, the first number indicates low-temperature fluidity. 5W means it can withstand temperatures as low as -30°C. The smaller this number, the better the low-temperature fluidity, making cold starts smoother. The second number represents the oil's kinematic viscosity at 100°C. A higher number means the oil can maintain its viscosity better at high temperatures, which can also be understood as better lubrication performance under high-temperature conditions. The method for changing the oil in a BMW X1 is as follows: Wait for the engine temperature to drop, allowing the oil to flow back into the oil pan. Use a wrench to loosen the oil drain plug and place an oil pan underneath to catch the old oil until it stops flowing. Start the engine for about 30 seconds to allow the oil in the main oil passage to drain out. Use a specialized wrench to remove the oil filter. Apply oil to the oil seal of the new oil filter and tighten it clockwise by hand. Add the new oil through the oil filler cap on the engine valve cover. Typically, fill about three-quarters of a standard oil container. Start the engine and let it run for 5 minutes, checking for any leaks around the oil drain plug and oil filter. If leaks are found, perform necessary repairs. After stopping the engine, pull out the oil dipstick to check that the oil level is within the standard range.

8

0

Share

Where is the ECU located on the Kawasaki ZX-14R?

The ECU of the Kawasaki ZX-14R is located under the seat. Open the seat and you will find it towards the rear section. Motorcycle ECU System: The motorcycle ECU system is part of the motorcycle's electronic fuel injection system. The motorcycle electronic fuel injection system is a set of engine management systems developed by ECOTTONS in the USA based on their independently developed ECU. The motorcycle fuel injection conversion kit (SE-EFI Kit) is a fuel injection kit suitable for small engine conversions. Installation Methods: Replacement Type. This involves directly changing the ECU hardware, commonly referred to as "replacement ECU" in racing circuits. It uses a "full replacement ECU" to control the engine. Brands like Motec and Haltech are well-known for their full replacement ECUs, typically used alongside extensive engine hardware modifications. Flash Tuning. Flash tuning retains the original ECU hardware and involves writing new operating management programs into the ECU. Since this alters the factory settings, flash-tuned ECUs are also known as reprogrammed ECUs or, colloquially, "ECU flashing."

13

3

Share

Can the New Regal be modified with automatic wipers?

The New Regal can be modified with automatic wipers. It requires replacing the front windshield, the rain and light intensity sensor along with its wiring harness, as well as the interior rearview mirror and its base. Wiper activation method: The rear wiper and front wiper switches are located together, which means pressing the control lever on the right rear side of the steering wheel. To control the rear wiper, first push the lever toward the front of the car, then adjust the wiper speed by moving the lever up and down to set the desired working speed level for the rear wiper. Replacement method: Lift the metal wiper arm away from the windshield and hold it steady in a position perpendicular to the windshield; remove the old wiper blade by separating it from the metal arm; press the tab to insert the new wiper, gently twisting the new blade; until the hook clicks into place to secure it, then lower the wiper back onto the windshield.

7

0

Share

Which is More Durable: Mechanical Gear Shift or Electronic Gear Shift?

Mechanical gear shifts have a shorter lifespan compared to electronic gear shifts. The specific differences between mechanical and electronic gear shifts are as follows: Safety Aspects: Electronic gear shifts rely on computer assistance for shifting, requiring only a signal input. Electronic gear shifts are typically automatic, whereas conventional gear shifts can be either manual or automatic and are mechanical in nature. Although mechanical automatic gear shifts also use computer assistance for shifting, electronic gear shifts offer better cost-performance and stronger safety features. Operational Feel: Electronic gear shift levers are more effortless to use, have a better appearance, and offer more advanced technology, but they come with higher maintenance costs. On the other hand, manual mechanical gear shift levers provide a stronger sense of control. Internal Volume of Gear Shift Lever: The transmission manual control valve in mechanical gear shift levers is located at the traditional position of the gear lever. Electronic gear shifts use motors to replace manual operations, eliminating the need to consider spatial positions and movement directions. Only switches and wiring need to be arranged, allowing flexible placement of the gear lever. Additionally, they can be designed in various styles, such as rotary knobs or buttons. Design Aspects of Electronic and Mechanical Gear Shifts: Electronic gear shift levers offer more flexibility for designers. Car interiors are an unavoidable consideration when choosing a vehicle, and automakers are constantly seeking breakthroughs. Compared to mechanical gear shifts, electronic gear shift levers can be freely designed by designers, leading to various types such as "chicken leg" shapes, electronic buttons, and rotary knobs. Electronic gear shift levers are more compact. Mechanical gear shifts require many components for shifting, some of which are used to control various valves. With electronic gear shift levers, many mechanical structures are replaced by electronic components and wiring, significantly reducing the overall size of the gear lever. Electronic gear shift levers are lighter and safer. Mechanical gear shifting requires manual pushing and pulling by the driver, whereas electronic gear shift levers make operations simpler. Mechanical gear shifts offer better reliability and a more distinct shifting feel. Electronic gear shift levers are controlled by electronic components, which are less reliable than mechanical gear shift levers and lack the distinct shifting sensation of mechanical gear shifts.

4

5

Share

How to update ETC after vehicle transfer?

Is It Normal for the Display Screen of Baojun 560 to Stay On After Turning Off the Engine?

What is the minimum ground clearance of the Tang?

How many liters of oil can a BMW X1 hold?

Where is the ECU located on the Kawasaki ZX-14R?

Can the New Regal be modified with automatic wipers?

Which is More Durable: Mechanical Gear Shift or Electronic Gear Shift?

What are the differences between the 911 and the Panamera?

What are the methods to remove formaldehyde from the car interior?

Does ETC have to be activated in the car?

What does the three horizontal bars on the Octavia dashboard km/h display mean?