How to Turn on the Heater in a BMW 3 Series?

2 Answers
EvelynRose
07/25/25 12:34pm
Method to turn on the heater in a BMW 3 Series: 1. After starting the car, wait approximately 6 to 8 minutes until the water temperature reaches normal operating temperature, then you can turn on the heater; 2. Adjust the air conditioning circulation mode to internal circulation; 3. Switch to the heater mode, indicated by the red zone; 4. Do not turn on the air conditioning, as the heater utilizes the car's own heat circulation to save energy; 5. Adjust the air conditioning to a suitable setting and direct the airflow as desired. In terms of appearance, the BMW 3 Series features a polygonal kidney grille and new Angel Eye headlights, with an additional groove below the center of the headlights. The bumper lines extend into the groove and connect with the headlights. The body dimensions are 4719mm in length, 1824mm in width, and 1459mm in height, with a wheelbase of 2851mm. For powertrain, the BMW 3 Series is equipped with a B-series 2.0T engine, paired with an 8-speed automatic transmission.
Was this review help?
8
2
Share
LeAlexander
08/11/25 8:24pm
Turning on the heater in a BMW 3 Series is actually quite simple. When I drive this car, I usually start the engine first and let it run for 2-3 minutes until the coolant temperature rises, at which point warm air starts coming out. Then, locate the air conditioning control area on the dashboard and simply rotate the temperature knob to the red marked zone or set it above 23°C. Press the AUTO button to let the system automatically adjust the fan speed and airflow direction—it will regulate itself based on the cabin temperature. If you prefer manual control, turn the fan speed knob higher and adjust the airflow direction to the footwell or windshield, which makes winter driving more comfortable and helps defog. Remember to use the recirculation mode for faster heating, but avoid blowing air directly at your face to prevent dryness. I make it a habit to warm up the car in advance during cold weather to avoid freezing on the road, which could affect safety. The car’s automatic climate control is designed intelligently and is very user-friendly.
Was this review help?
5
0
Share
Expand All
More Forum Discussions

What are the symptoms of a broken car compressor?

Symptoms of a broken car compressor: 1. Air conditioning does not cool: When the AC switch is turned on, the engine speed does not increase. If air conditioning is not needed, removing the compressor belt can increase power by more than half a gear without affecting the car; 2. Exhaust valve damage: The compressor electromagnetic clutch coil burns out. Generally, if the intake and exhaust valves are broken, the compressor must be replaced. If the compressor electromagnetic clutch coil is burned, it can be replaced; 3. Compressor fails to rotate: There is abnormal noise during rotation, abnormal pressure, high pressure is low, low pressure is high; 4. The air conditioning compressor is not powered by electricity but is driven by the engine gear or belt. When the air conditioning is off, the compressor is idling.
5
0
Share

Can Subject Two and Subject Three be Scheduled Together?

Subject Two and Subject Three can be scheduled for examination at the same time, but simultaneous scheduling is not available in all regions and requires local conditions to support it. Below is the relevant content introduction: 1. Supporting simultaneous scheduling: If local conditions permit, candidates can schedule the exams through the national unified examination scheduling system using conventional scheduling methods, such as the Traffic Comprehensive Service Management Platform or the Traffic Management 12123 mobile app. 2. Relevant regulations: According to the "Regulations on the Application and Use of Motor Vehicle Driving Licenses," the number of scheduled examinations for the site driving skill test and the road driving skill test (i.e., Subject Two and Subject Three) must not exceed five times. If the fifth examination is still failed, the previously passed examination results will be invalidated.
12
1
Share

Should an automatic transmission car be turned off first or shifted into P gear first?

It should be turned off first and then shifted into P gear. The correct shutdown procedure is to stabilize the car, shift the gear to N, engage the handbrake, turn off the engine, and then shift the gear to P. Here are the relevant introductions: 1. Automatic transmission: As the name suggests, an automatic transmission does not require the driver to manually shift gears. The vehicle will automatically select the appropriate gear based on the driving speed and traffic conditions. Generally, an automatic transmission car has six gear positions, from top to bottom: P, R, N, D, S, L. 2. Automatic principle: The engine's power is transmitted through the gearbox, which is also a key factor affecting fuel consumption. Generally, an automatic transmission consumes more than 10% more fuel than a manual transmission.
19
2
Share

What is tire pressure loss?

Generally, there are three reasons for tire pressure loss. The first is related to load capacity. The second is related to seasonal changes. The third is related to tire specifications. Tire Pressure Reset: Tire pressure reset refers to the operation of resetting the tire pressure monitoring system after addressing a tire pressure malfunction. Tire Pressure Reset Method: First, turn on the ignition switch, then press and hold the tire pressure monitoring reset button until you hear a "ding" sound before releasing it. The tire pressure monitoring system will then store the current normal tire pressure data, automatically clear the previous data, and finally, the warning light on the dashboard will turn off, indicating the completion of the tire pressure reset.
4
4
Share

What are the symptoms of a faulty transfer case in a BMW X6?

BMW X6 transfer case failure manifests as the inability to switch to four-wheel drive mode or the occurrence of unusual noises while driving. Here are additional details: 1. Function of the transfer case: The primary role of the transfer case is to rationally distribute the engine's power, delivering it to the rear axle or simultaneously to both the front and rear axles. It enables the switching of the vehicle's drive mode, allowing a four-wheel-drive vehicle to switch to two-wheel drive. 2. Precautions: The transfer case contains specialized gear oil, which should be replaced regularly. It is recommended to replace it when the vehicle has traveled approximately 60,000 to 80,000 kilometers. When switching drive modes using the transfer case, it is best to do so when the vehicle is stationary to prevent wheel backlash from damaging the transfer case.
2
3
Share

What is the BMW 7154ac?

BMW 7154ac is the 2018 model of the BMW 1 Series 1.5T Sport Automatic, equipped with a 1.5T turbocharged engine. Here is some extended information: 1. BMW: BMW (short for Bayerische Motoren Werke) is a German automobile brand under the BMW Group. It has four model lines: i, X, Z, and pure numbers, as well as series like 1, 2, 3, and the M series (BMW's official high-performance modification division) based on improvements to these series. 2. Advantages of turbocharging: The biggest advantage of turbocharging is that it can significantly increase the engine's power and torque without increasing the engine displacement. Turbocharged engines are not only more fuel-efficient but also reduce emissions of CO (carbon monoxide), CH (hydrocarbons), and PM (particulate matter).
20
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.