How to Test for Car Battery Leakage?

What engine does SAIC MG use?

MG is equipped with the 'Blue Core' SGE20T engine, jointly developed by SAIC Group and General Motors. This 1.5-liter turbocharged engine delivers a maximum power of 169 horsepower and a peak torque of 250 Nm. More information about MG engines is as follows: 1. MG Powertrain: MG engines are divided into two models, one is a 1.0T in-cylinder direct injection turbocharged engine, and the other is a 1.5L naturally aspirated engine with a maximum horsepower of 120 and a peak torque of 150 Nm. 2. Features of the Blue Core Series Engine: MG's 1.0T is one of SAIC's Blue Core series engines, with main technical features including in-cylinder direct injection system, dual variable valve timing, variable oil pump, water-cooled exhaust manifold, all-aluminum cylinder block, etc.

14

3

Share

Why does the clutch become stiff when the car's air conditioning is on?

This is a normal situation because when the air conditioning compressor is activated, the engine load increases, causing vibrations that make the clutch pedal feel stiff. Here is some related information about car air conditioning: 1. How to use the A/C button: When the weather is hot and you need to turn on the air conditioning to cool down, press the AC button, adjust the temperature control knob to the blue section, and then turn on the fan switch. The indicator light will illuminate, and the car's air conditioning compressor will start working, blowing cold air from the vents. 2. How car air conditioning works: When the air conditioning is turned on, air will blow out because the blower in the air conditioning system starts working. However, the air conditioning cooling system has not yet started because the compressor has not begun to operate.

1

3

Share

How many seconds does the Boyue Pro take to accelerate from 0 to 100 km/h?

According to official data, the Boyue Pro comes in two models: 1.8T and 2.0L. The 1.8T two-wheel-drive model accelerates from 0 to 100 km/h in 10 seconds, while the 2.0L four-wheel-drive model takes 11 seconds. Factors affecting a vehicle's 0-100 km/h acceleration time include: Torque: Torque, in layman's terms, represents how much force is available. The greater the torque, the more force is available to propel the vehicle, resulting in faster acceleration. For example, the BMW X2 has a maximum torque of 220 Nm and accelerates from 0 to 100 km/h in 9.6 seconds. The Boyue Pro 1.8T has a torque of 300 Nm and accelerates in 10 seconds. Transmission efficiency: The transmission is the medium for power transfer and inevitably involves power loss. The higher the transmission efficiency, the better the acceleration performance. Generally, transmission efficiency ranks as follows: manual transmission > dry dual-clutch transmission > wet dual-clutch transmission > AT transmission > CVT transmission. The Boyue Pro is equipped with a 7-speed wet dual-clutch transmission. Power-to-weight ratio: The relationship between horsepower and vehicle weight is called the power-to-weight ratio (measured in Hp/T). The higher the power-to-weight ratio, the faster the acceleration. For example, the BMW X2 has a power-to-weight ratio of 90 Hp/T and accelerates from 0 to 100 km/h in 9.6 seconds. The Boyue Pro has a power-to-weight ratio of 109 Hp/T and accelerates in 10 seconds.

11

2

Share

Where is the drainage hole located under the door of the Peugeot 3008?

The drainage hole under the door of the Peugeot 3008 is located beneath the door seal at the bottom of the door panel. Here are the specific details: 1. Introduction to the drainage hole: The drainage hole is primarily designed to drain rainwater that seeps into the door interior from the gaps around the windows. Vehicle drainage holes are outlets that allow accumulated water to drain out of the vehicle during rainy weather, and their principle and structure are very simple. 2. Distribution of drainage holes: The drainage holes in a car are generally located in areas such as the fuel tank cap, engine compartment, under the door panels, and sunroof. The most prone areas for clogging are the sunroof and engine compartment. The initial clogging of the sunroof drainage hole occurs at the entrance of the hole, which can be seen by opening the sunroof. At this stage, it is relatively easy to clean and can be done by oneself. Over time, the clog may move into the drainage hose, making it more difficult to unclog as it progresses further along the hose.

4

3

Share

Can Only the Car Light Cover Be Replaced If It's Broken?

It is not possible to replace only the light cover. If the car headlight cover is broken, the entire headlight assembly must be completely replaced. You cannot just replace the light shell, and there are no separate light covers available for sale. If the headlight assembly is not replaced, it may lead to water ingress, which can affect the brightness of the vehicle's lights, cause short circuits in the lights, and damage the electrical circuits. Additionally, it can lead to traffic accidents while driving. Below is relevant information about car light covers: 1. Material of Car Light Covers: The glass covers of vehicle headlights and taillights are made of high-grade polycarbonate (also known as PC, the same material used for resin eyeglass lenses) through injection molding. Polycarbonate is known for its high hardness, strength, toughness, UV resistance, and good light transmission. 2. Characteristics of High-Quality vs. Low-Quality Light Covers: High-quality bulbs have good light distribution and high brightness, whereas low-quality bulbs lack sufficient brightness, have poor focus, and short projection distance. When overtaking, low-quality bulbs can create visual illusions for the driver, increasing the risk of accidents. Therefore, when modifying headlights yourself or needing replacements due to damage, never consider low-quality bulbs.

9

0

Share

What is the reason for severe shaking when starting the Sail?

The most common cause of severe shaking when starting the Sail is a dirty throttle body or excessive carbon buildup in the fuel injectors. Below are the relevant explanations: 1. Excessive carbon buildup: When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts, making it difficult to start. In this situation, the engine will only start easily once the carbon deposits have absorbed enough gasoline to become saturated. After starting, the gasoline adsorbed on the carbon deposits is then drawn into the cylinders by the engine's vacuum suction to burn, making the air-fuel mixture too rich. The engine's combustible air-fuel mixture alternates between being too lean and too rich, causing idle shaking after a cold start. The lower the temperature, the more fuel is required for a cold start, and the presence of carbon deposits will significantly affect whether the cold start proceeds smoothly. 2. Air-fuel mixture: A too-lean air-fuel mixture during a cold start makes it difficult to start until the carbon deposits absorb enough gasoline to become saturated. After starting, the gasoline adsorbed on the carbon deposits is drawn into the cylinders by the engine's vacuum suction to burn, making the air-fuel mixture too rich. The engine's combustible air-fuel mixture alternates between being too lean and too rich, causing idle shaking after a cold start.

3

4

Share

How to Test for Car Battery Leakage?

What engine does SAIC MG use?

Why does the clutch become stiff when the car's air conditioning is on?

How many seconds does the Boyue Pro take to accelerate from 0 to 100 km/h?

Where is the drainage hole located under the door of the Peugeot 3008?

Can Only the Car Light Cover Be Replaced If It's Broken?

What is the reason for severe shaking when starting the Sail?

What is the model number of the oil filter for the Roewe RX5?

Does the ACC warning light affect normal driving?

Should You Depress the Clutch During Curve Driving?

Difference Between Reiz Electronic Shock Absorbers and Conventional Shock Absorbers?