How to Set Memory Seats in the Atenza?

How to Lift the Wiper Blades Up?

Method to lift the wiper blades: When the engine is turned off and the power is shut down, push the wiper lever upward for about 3 seconds to lift them. Possible causes of wiper damage are generally as follows: 1. Poor road conditions with a lot of mud and sand particles can greatly affect the wipers. 2. Turning on the wipers before spraying water in rainy conditions. 3. Using tap water instead of windshield washer fluid. Typically, it is recommended to replace the wiper blades once a year. However, if the wiping effect is still good and the wiper rubber has not aged, the replacement can be delayed. The key factor is the condition of the wipers themselves. If within less than a year the wipers leave obvious streaks when wiping and the rubber feels hard, it's time to replace them.

14

3

Share

What Do Car Tire Model Numbers Represent?

Car tire specification model parameters are expressed in millimeters to indicate the section width and the percentage of the aspect ratio. Following this are: the tire type code, rim diameter (in inches), load index (code for permissible load capacity), and permissible vehicle speed code. The size model of the tire is as follows: 1. The tire model refers to the international standard tire code, expressed in millimeters to indicate the section width and the percentage of the aspect ratio, sequentially arranged as the tire type code, rim diameter (in inches), load index (or load capacity index), and maximum speed code. 2. Car tire sizes are generally in the form of numbers plus letters, and the meanings represented by these numbers and letters help in better selection, usage, and maintenance of the tires.

11

5

Share

Is it normal for the engine to make abnormal noises when starting?

A normal engine should not produce any sharp noises during the startup process, and the idle sound should be uniform. When starting a cold engine, there might be a ticking sound, which diminishes and disappears as the engine warms up—this is considered normal. When gently pressing the accelerator to gradually increase the engine speed, the engine should run smoothly without any unusual noises. Rapidly pressing the accelerator pedal should result in a smooth increase in engine power without any hesitation or metallic knocking sounds. After driving the vehicle in a simulated mixed road condition for 5-10 minutes in an open area, the idle speed should remain stable without fluctuation, and the engine sound should be steady and uniform. Below are some reasons why a car engine might become louder: 1. The engine makes a ticking sound, similar to a pencil tapping on a table, and the sound increases with engine speed. Possible causes include contaminants inside the engine—recommend changing the oil and oil filter, and cleaning the engine. Other possibilities could be valve issues. 2. While driving, acceleration and ignition may seem normal, but if you notice the engine RPM is too high while maintaining a constant speed, yet the speed doesn’t increase accordingly. Check the coolant level, oil pressure (too high or too low), inspect the oil pressure gauge, or verify the ignition timing settings, as these could cause such symptoms. Other potential issues might involve internal engine problems, such as a clogged EGR valve. 3. The engine makes a tapping sound at idle, as if something is hitting metal. This sound might not be noticeable during acceleration or driving. Possible causes include cylinder valve issues—adjusting the valves may help. Low oil levels or insufficient oil pressure could also lead to similar problems, so check the engine oil pressure. 4. A whirring sound occurs during acceleration or deceleration, changing with RPM. Possible causes include low power steering fluid—top it up. Damaged alternator bearings, issues with the power steering pump, or water pump could also produce similar noises. 5. Pressing the accelerator pedal results in a popping sound from the exhaust, which might not be very loud. The car may drive normally, but fuel consumption could increase. Inspect the muffler and exhaust pipe for any damage.

18

2

Share

Where is the battery jump-start location for the BMW X6?

The jump-start location for the BMW X6 battery is on the positive and negative terminals of the battery. Below are the specific steps for jump-starting: 1. First, prepare the jumper cables. 2. The black clamp should be attached to the negative terminal of the battery, and the red clamp should be attached to the positive terminal. First, locate the batteries of both vehicles. Then, attach the red cable to the positive terminal of one vehicle and the other end of the same cable to the positive terminal of the other vehicle. Next, attach the black cable in the same manner to the negative terminals of both vehicles. 3. Once both cables are connected, start the vehicle normally. After the vehicle starts, you can remove the two cables. When removing the cables, do so one by one, not removing all from one vehicle before moving to the other.

12

1

Share

Can FAW-Volkswagen Jetta VS5 use 92 gasoline?

Jetta VS5 cannot use 92 gasoline. The Jetta VS5 is equipped with a 1.4-liter turbocharged engine across all models, and this vehicle requires a minimum of 95 gasoline. Generally, turbocharged engines require at least 95 gasoline. If 92 gasoline is used, the turbocharged engine is prone to knocking. Relevant information about gasoline is as follows: 1. The English name for gasoline is 'gasoline' or 'gas' (American English), also known as 'petrol' (British English). It is a volatile, flammable hydrocarbon mixture liquid distilled or cracked from petroleum, primarily used as fuel for spark-ignited internal combustion engines. 2. Gasoline with different octane ratings has different levels of octane; the higher the octane rating, the higher the octane level of the gasoline.

18

2

Share

What Does the Vehicle Identification Number Represent?

Vehicle Identification Number, abbreviated as VIN, is a unique set of seventeen letters or numbers used on automobiles to identify the manufacturer, engine, chassis serial number, and other specifications of the vehicle. To avoid confusion with the numbers 1, 0, and 9, the letters "I", "O", and "Q" are not used. The 10th digit, representing the model year, does not use "I", "O", "Q", "U", "Z", or "0". More details are as follows: 1. There are specific rules for interpreting vehicle information through the VIN. Illegal characters include O, Q, and I. The letter Z is not valid in the model year position. The ninth digit can only be a number from 0 to 9 or the uppercase letter X. The last four digits must all be numbers and cannot be letters. 2. The VIN standard can be used to analyze vehicle configurations. Digits four to eight represent the engine and transmission model, which must match the information on the assembly nameplate without discrepancies. In terms of vehicle body styles, many vehicles typically have corresponding configurations and shapes. 3. This information also indicates the number of doors and windows, loading characteristics, and other details. For example, a sedan usually has two doors and four windows, while an MPV model has five doors and can be a hatchback, light truck, or heavy truck.

6

1

Share

How to Set Memory Seats in the Atenza?

How to Lift the Wiper Blades Up?

What Do Car Tire Model Numbers Represent?

Is it normal for the engine to make abnormal noises when starting?

Where is the battery jump-start location for the BMW X6?

Can FAW-Volkswagen Jetta VS5 use 92 gasoline?

What Does the Vehicle Identification Number Represent?

How Much Steering for Left Turn in Subject Three?

How to Open the Inner Fuel Tank Cap of a Car?

What type of oil does the T-Roc use?

Is It a Problem If the Car's Underbody Is Scraped?