How to reset the tire pressure monitoring system on BYD F3?

2 Answers
StAnastasia
07/28/25 7:45pm
The method to reset the tire pressure monitoring system on BYD F3: Adjust the underinflated tire pressure to the standard value, then drive at a constant speed of 40 km/h for about 10 minutes. The tire pressure monitoring system will recalibrate automatically, and the tire pressure warning light will turn off once the recalibration is successful. If the tire pressure warning light comes on while driving, reduce speed, maintain control of the steering wheel, and find a safe place to inspect the tires. The BYD F3 is an A+ class sedan produced by BYD Auto, with dimensions of 4533mm in length, 1705mm in width, 1490mm in height, and a wheelbase of 2600mm. The interior design of the BYD F3 features a simple and elegant style, with a fresh light color scheme and comprehensive, well-equipped configurations.
Was this review help?
15
1
Share
DeGenesis
08/12/25 12:38am
I've been driving a BYD F3 for several years, and it's really annoying when the tire pressure monitoring light comes on. To clear the warning light, you need to follow these steps: First, park and check the air pressure of all tires to ensure they meet the standard values in the manual when cold (around 2.3-2.5 bar). After confirming the tire pressure is correct, get in the car and start the engine, but don't drive off immediately. Look for the buttons on the left side of the steering wheel, usually the ones for adjusting volume or menu. Press and hold the 'SET' button for a few seconds until a reset prompt appears on the dashboard, and the light will go off. There's a little trick to this operation—I often help friends with it—you must keep the car stationary while holding the button. If the light doesn't go off, the sensor might be faulty, and you'll need to visit a 4S shop for inspection. Make sure to check the tire pressure regularly, as sensors can easily malfunction after frequent highway driving, preventing the light from coming on again next time. Safety comes first, so don't keep driving if the light is on.
Was this review help?
16
0
Share
Expand All
More Forum Discussions

What is the fuel tank capacity of the 2010 Nissan Livina?

2010 Nissan Livina 1.6 has a fuel tank capacity of 52 liters. It is equipped with a 1.6-liter naturally aspirated engine, coded as HR16, and all models come with either a 5-speed manual transmission or a CVT transmission. The 1.6-liter naturally aspirated engine of the Livina delivers a maximum power of 91 kW and a maximum torque of 153 Nm. The engine reaches its peak power at 5,600 rpm and its peak torque at 4,000 rpm. This engine features E-VTC technology and multi-point fuel injection, and it utilizes an aluminum alloy cylinder head and block. During actual refueling, the amount of fuel may exceed the marked capacity. This is because the fuel tank capacity specified by the manufacturer is measured from the bottom of the tank to the safety limit, and there is additional space from the safety limit to the tank opening. This extra space ensures that the fuel can expand when temperatures rise without overflowing from the tank. If fuel is filled up to the tank opening during refueling, the actual fuel amount may exceed the marked capacity. To check the remaining fuel level, drivers can observe the fuel gauge on the right side of the instrument panel, which is marked with 'E' and 'F'. When the needle is close to 'E', it indicates low fuel, while near 'F' means the tank is nearly full.
13
5
Share

What is the fuel tank capacity of the 2017 Lamando?

2017 Lamando has a 50-liter fuel tank. The Lamando is a compact car launched by SAIC Volkswagen, with dimensions of 4598mm in length, 1826mm in width, and 1425mm in height, and a wheelbase of 2656mm. It has a maximum power output of 110kw and a top speed of 215 km/h. The fuel tank capacity for all variants of the Volkswagen Lamando is 50 liters, with a trunk volume ranging from 480L to 1150L (1150L when the rear seats are folded down). If the owner wants to check the remaining fuel level, they can observe the fuel gauge on the right side of the dashboard, which is marked with E and F. When the needle is close to E, it indicates low fuel, and when it is near F, it means the fuel level is sufficient. Maintenance tips for the fuel tank are as follows: Drain accumulated water and sediment from the fuel tank, and check for any leaks at the fuel pipe connections and switches. For fuel tank caps equipped with air valves and vapor valves, also check if the ventilation holes are clear. The filter screen at the fuel filler neck should be kept intact to prevent impurities from entering the tank during refueling, which could clog the fuel lines. The sealing gasket on the fuel filler cap should also be in good condition to prevent fuel from spilling out while driving.
4
4
Share

What Are the Symptoms of a Faulty Car Air Conditioner Blower Resistor?

When a car blower resistor is faulty, the most obvious symptom is the inability to adjust the air conditioner's fan speed, as the primary function of the car blower resistor is to control the speed of the fan. Method to determine if the blower resistor is damaged: Prepare a multimeter, set it to the ohm range, place the red probe of the multimeter on the positive terminal of the resistor and the black probe on the negative terminal. Then check if the reading on the multimeter is normal. If the measured resistance value is 0, it indicates that the resistor is damaged. If the blower resistor is faulty, it needs to be replaced. The replacement steps are as follows: Prepare the necessary tools for replacement, such as a new blower resistor and a Phillips screwdriver, then turn off all the vehicle's electrical equipment and the ignition switch; disconnect the vehicle's battery and the blower assembly connector (the blower is usually located under the glove compartment in front of the passenger seat), remove the blower's fixed wiring harness, then unscrew the blower assembly's mounting screws; You can find the resistor at the location where the blower was removed (connected near the air duct), use tools to remove it, and install the new resistor; Reinstall the blower and all the wiring, then reconnect the battery, start the car and turn on the blower to check if the fan speed can be adjusted.
6
4
Share

What is the weight of the Geely Emgrand GL?

Geely Emgrand GL weighs around 1.4 tons. More information about Geely Emgrand GL is as follows: 1. The letter G in Emgrand GL represents the higher positioning of Emgrand GL within the Emgrand series, while L is regarded as "Long", implying that Emgrand GL has a larger interior space. 2. Emgrand GL adopts the very popular "fastback" lines and short tail design, making it visually more dynamic. The integrated eye-catching LED light guide taillights not only enhance the premium feel of the rear, but also form smooth lines with the license plate frame, resembling a soaring eagle, echoing the dynamic upward tail wing, enriching the layers of the rear.
17
5
Share

At what percentage of oil life should the Regal's engine oil be changed?

The engine oil in the Regal can be changed when the oil life drops below 50%. The oil life depends on various factors, including engine speed, temperature, and mileage. Depending on driving conditions, the mileage at which the oil change is indicated can vary significantly. If the vehicle is driven under favorable conditions, the oil life will be longer, whereas under harsh conditions, the oil change interval will be considerably shorter. Symptoms indicating the need for an oil change: Increased engine noise during operation. Symptoms of reduced engine power and sluggish acceleration. The oil turns black and contains impurities. The oil emits a foul odor; if the oil deteriorates, it will have a strong, unusual smell. Methods to check oil life: First, pull out the oil dipstick located near the engine, then take a small amount of oil and drip it onto an oil test paper. Let it sit overnight, allowing the oil to fully spread on the paper. Then, observe the sediment ring, oil ring, and diffusion ring on the paper. If any of the following three conditions occur, it means the oil needs to be changed: If the boundaries between the three rings are distinct, the oil can still be used for a while, but it should be changed as soon as possible. If the oil ring disappears, leaving only the sediment ring and diffusion ring, take the vehicle to the nearest repair shop for an oil change, or you can change it yourself. If only the darker-colored sediment ring remains, the oil must be changed immediately to avoid potential engine damage.
12
2
Share

What does the W gear of Roewe 350 mean?

Roewe 350W gear is the snow mode, which is used for starting on slippery surfaces. It generally controls the torque in 2nd gear, providing less starting power than 1st gear to avoid wheel slippage. Below is the relevant introduction about the W gear: 1. The W key is the snow driving mode key. When this mode is enabled, the engine's torque is suppressed, preventing it from quickly reaching the peak torque, thereby reducing the likelihood of wheel slippage during snow driving. 2. In fact, as long as you start driving on slippery roads, turning on the W key can make the car start smoothly and avoid tail swing.
18
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.