How to Reset the Maintenance Reminder Light on Chery Vehicles?

Why does the car's one-button start fail to ignite?

Reasons why the car's one-button start fails to ignite: 1. The car steering wheel is locked: If the steering wheel is turned after the vehicle is turned off, it will be locked. In this case, simply turn the steering wheel left or right while pressing the one-button start. 2. The gear is not in P (Park) position: Due to the system's protection mechanism, an automatic transmission car cannot be started if it is not in the P (Park) position. 3. The car key battery is dead: When the car key battery is dead or low on power, the car's internal sensors cannot detect it, so the vehicle will not start. 4. Some car models require pressing the one-button start twice to start the car, while others require holding the one-button start for a longer duration.

13

1

Share

What to Do When There's Noise While Operating Car Windows?

If there's noise when operating car windows, you can replace aged sealing strips, clean debris from the window tracks, and regularly lubricate the gear assembly. Unusual sounds during window operation are mostly caused by accumulated dust in the rubber guide channels or aging rubber. To clean debris from the window tracks, first wipe the window glass clean, then lower it completely and raise it to the top, repeating this two or three times. Shallow sand particles can usually be removed by the sealing strips. If this doesn't work, wet the window glass and operate it again. You'll see marks where sand particles are located. Lower the glass completely, use a thin, flat hard object to hold a wet towel, insert it into the gap of the secondary sealing strip, and wipe back and forth several times to solve the problem.

18

1

Share

How to Remove Formaldehyde in the Car?

Methods to remove formaldehyde in the car are as follows: 1. Ventilation: For the first six months after purchasing a new car or after interior decoration updates, develop the habit of driving with windows slightly open to maintain fresh air circulation and accelerate the dissipation of odors inside the car. 2. Activated carbon adsorption: Activated carbon has strong adsorption properties and is a common method for formaldehyde removal in daily life. However, activated carbon becomes saturated quickly and needs to be replaced with new carbon packs promptly after saturation. 3. Air compressor solvent atomization: Use an air compressor to atomize and evenly spray "formaldehyde cleaner" solvent inside the car, ensuring the spray covers all interior components and corners.

2

3

Share

What Causes Car Shaking During Cold Start?

Cold start body shaking has the following reasons: 1. The main reason is incomplete fuel combustion: resulting in insufficient power output. 2. Low ignition energy: During startup, especially when fuel and lubricant temperatures are low, revving the throttle is required to meet power demands. Over time, the electrode gap of spark plugs gradually increases, leading to reduced ignition energy and poor fuel atomization, consequently causing body shaking. 3. Aging ignition coils, or aging/sparking high-voltage wires of spark plugs: resulting in decreased ignition energy and subsequent body shaking.

3

5

Share

How to reset the maintenance light on the Leiling?

Method to reset the maintenance light on the Leiling: 1. Put the Leiling in ON mode; 2. Press the maintenance light reset button and rotate until the short-range odometer appears; 3. Turn off the ignition switch, i.e., OFF mode; 4. While holding down the maintenance light reset button and rotating, switch the ignition back to ON mode, then continue holding and rotating the reset button until the odometer is cleared. After 5 seconds, the odometer will display 000000, indicating the maintenance light has been successfully reset. The new Toyota Leiling offers both fuel and hybrid versions. The new Leiling's sport version comes with additional sport kits, including front and rear aerodynamic bumpers, a sporty mesh piano-black front grille, and sport-specific seats. The gasoline sport version also features a lowered body stance.

14

1

Share

Where is the spark plug located in a sedan?

The spark plug in a sedan is located at the top of the engine cylinder. Types of spark plugs: 1. Standard spark plug: The insulator skirt is slightly recessed into the shell end face, and the side electrode is outside the shell end face; 2. Extended insulator spark plug: The insulator skirt is longer and protrudes beyond the shell end face; 3. Fine electrode spark plug: Its electrodes are very thin, characterized by strong sparks and good ignition capability, ensuring quick and reliable engine start even in cold seasons, with a wide heat range suitable for various uses; 4. Tapered seat spark plug: Its shell and threaded part are conical, so it can maintain good sealing without a gasket; 5. Multi-electrode spark plug: Generally has two or more side electrodes, with the advantage of reliable ignition and no need for frequent gap adjustment; 6. Surface gap spark plug: Also known as the surface gap type, the gap between the center electrode and the shell end face is concentric.

16

5

Share

How to Reset the Maintenance Reminder Light on Chery Vehicles?

Why does the car's one-button start fail to ignite?

What to Do When There's Noise While Operating Car Windows?

How to Remove Formaldehyde in the Car?

What Causes Car Shaking During Cold Start?

How to reset the maintenance light on the Leiling?

Where is the spark plug located in a sedan?

How many seats does the Porsche 911 have?

Where is the car thermostat generally located?

What is the ground clearance of the CHR?

What does the fuel gauge symbol EF on the car dashboard represent?