How to reset the maintenance reminder for the 2019 Tayron?

[MaciLynn]

Select maintenance and press the OK button to enter; move the cursor to select reset, then press OK; when prompted to confirm resetting the maintenance cycle data, press OK. The original purpose of the car maintenance reminder light is to alert the owner to perform maintenance as soon as possible. After completion, the 4S shop will use a fault diagnostic tool to reset the maintenance light. The maintenance reminder light will only illuminate when factors such as the driven mileage, time, road conditions, and usual load fall below a certain set value.

[VanLilliana]

The maintenance reminder on my 2019 Tayron was really annoying every time it popped up. I figured out a reliable method myself: First, completely turn off the engine, then press and hold the 0.0 button at the bottom right of the instrument panel without releasing it. Next, power on the car but don't start the engine. Wait until the maintenance menu appears on the instrument panel, then release the button and immediately press the OK button on the left side of the steering wheel. This will display the reset option—press OK again to confirm, and it's cleared. Once, I pressed too quickly and it didn't work, but later I realized I needed to wait for the menu to fully load before proceeding. After resetting, remember to drive a few kilometers to confirm the warning light is actually off. This trick works for most Volkswagen group models and is much more convenient than going to the dealership. Just be careful not to press the brake pedal during the process to avoid accidentally starting the engine.

[SanConnor]

Resetting the maintenance reminder on the 2019 Tayron is actually quite simple. Let me show you: After parking and turning off the engine, hold down the 0.0 button on the instrument panel, then power on until the instrument panel lights up. Wait for the maintenance message to appear, release the button, and press OK to confirm. The key is to complete the entire process within 15 seconds—if you're too slow, the system will exit. Once, my friend's navigation-equipped model required an extra press of the menu button, so it depends on the specific configuration. After resetting, it's best to drive a few kilometers to test it. If it fails, it might be because the last maintenance wasn't fully reset. Doing it yourself saves time and money compared to visiting the dealership—just make sure not to do it while the engine is running.

[SanAdrian]

To reset the maintenance light, follow these four steps: After turning off the engine, press and hold the 0.0 button on the dashboard. Power on the vehicle and wait for the maintenance reminder to appear on the screen. Release the 0.0 button and immediately press the OK button on the steering wheel. Finally, select reset to confirm. The key is to complete the operation within ten seconds after powering on; otherwise, it will time out and fail. For my premium Tiguan L, it took driving two kilometers for the display to refresh after resetting, while the base model takes effect immediately after the operation. Don't panic if it fails; repeating the process twice usually ensures success, as the issue is often due to the reset procedure not completing fully.

[BrooklynAnn]

Last week, I just dealt with the maintenance reminder for my Tiguan. The steps were to first turn off the engine, press and hold the 0.0 button on the right side of the dashboard, rotate the key to power on until the dashboard lights up, wait for the maintenance menu to appear on the screen before releasing the button, and then quickly press the confirm button on the left side of the steering wheel. Remember not to press the brake during the entire process to avoid starting the engine. Once I failed because the 4S shop had upgraded the car's system, and I later succeeded by pressing and holding the OK button for ten seconds to force a reset. After resetting, it's best to record the mileage for reference during the next maintenance.

[SophieDella]

Experience sharing on resolving maintenance reminder pop-up: In a completely powered-off state, press and hold the 0.0 button on the dashboard without releasing, then power on to see the wrench icon appear on the dashboard. At this point, release the button and immediately press the OK button to enter the menu, select the reset option, and confirm. Operations may vary slightly for different model years of the Tayron, such as those with LCD dashboards requiring the use of steering wheel buttons. Some car owners have encountered situations where it only worked after disconnecting and reconnecting the battery. After resetting, drive for a while to observe if the reminder truly disappears to avoid misjudgment. Doing it yourself saves two hundred bucks compared to going to the shop.