How to reset the maintenance reminder for the 2019 Haval H6?

[OJeffrey]

Methods to reset the maintenance reminder for the 2019 Haval H6: 1. Turn off the ignition, press and hold the button at the lower right of the instrument panel; 2. Turn the ignition to the position where all dashboard lights are on, and you will notice the small wrench icon on the dashboard stops flashing; 3. Release the button and then press the button at the lower left of the instrument panel, and you will see the small wrench icon disappear; 4. The reset is complete. The 2019 Haval H6 has a body size of 4649mm in length, 1852mm in width, and 1710mm in height, with a wheelbase of 2680mm. The vehicle features front-wheel drive, a front suspension type of MacPherson independent suspension, a rear suspension type of double wishbone independent suspension, and a unibody structure.

[DiHarmony]

DIY maintenance reminder reset is actually quite simple. I encountered this before with my 2019 Haval H6. First, turn the key to power on (but don't start the engine), then watch the dashboard while holding down the button with the square symbol on the right side of the steering wheel. After about 4-5 seconds, the setup menu will pop up. Use the steering wheel toggle buttons to find the 'Maintenance Reset' option, enter to confirm reset, then turn off the power and restart the engine. Just a reminder - when I first tried this, I forgot to disconnect the car's Bluetooth and the screen froze once, so it's best to turn off all electronic devices before operating. If you really can't manage it, just drive to the 4S shop where they can finish it in three minutes with a diagnostic tool, but doing it yourself does save time.

[VanJude]

My 2019 H6's maintenance reminder light came on last year. Remember there are four steps to reset it: turn the key to ON position without starting, find the TRIP button on the right side of the steering wheel and hold for 5 seconds, select Vehicle Settings → Maintenance Info → Reset Mileage after the menu pops up. Here's the key - make sure to exit the menu before turning off the power. Once I turned the key off too quickly and had to redo everything. Also, confirm the mileage before resetting - changing the shop's 5,000km reminder to 8,000km could cause issues since this turbocharged engine shouldn't delay maintenance. Finally, check the multifunction steering wheel buttons - some owners couldn't access the menu due to faulty button contacts.

[StKendra]

The technician taught me how to operate it during the last maintenance. Make sure the car is powered on but the engine is not running. Press the bottom toggle button on the right side of the steering wheel until the settings menu appears on the dashboard. Find the reset option in the maintenance information section and press the confirm button. The key is to hold the confirm button for more than three seconds until the prompt disappears. This trick works especially well for high-end models with leather steering wheels and cruise control, while the button layout is different for base models with plastic steering wheels. After resetting, remember to drive about 200 kilometers to observe. Once, the prompt reappeared after just two kilometers post-reset, and it turned out to be a wiring mistake from a previous center console screen modification. By the way, remember to return the wiper lever to its original position before powering off.

[VanJoanna]

Key points for maintenance light reset: Power on without starting, long press the dashboard reset lever to enter engineering mode (some models require simultaneous brake pedal press). When helping a friend with a 2019 H6, I found the Sport version requires pressing both OK button + volume knob to access the engineering menu. Use steering wheel controls to navigate to maintenance info page - reset only takes effect when mileage is zeroed. Last time my friend's reset failed because the dealership forgot to clear the maintenance interval counter after previous service. After modification, always turn off ignition for 30 seconds before restarting - immediate start will trigger the light again. Note: Window tint moisture or aftermarket electronics may cause button malfunctions affecting operation.

[OHope]

My experience can be divided into three operational stages. Preparation stage: Turn off the engine, open the door to restart the car's computer, then power on and activate the hazard lights (to prevent battery drain). Operation stage: Press the menu button on the steering wheel to select the 'Maintenance' option. For newer versions of the car's system, you need to enable engineering mode permissions on the central control screen first. The key lies in the third stage: After resetting, you must drive at least 30 kilometers for the system to automatically update the maintenance cycle data. Once, after resetting and driving on the highway, I noticed the warning light flickering, and upon inspection, found it was due to unstable generator voltage causing data storage failure. By the way, prolonged neglect of the warning might affect the communication of the tire pressure monitoring module, so it's best to address it within two months.