How to reset the fog light warning light on Audi Q7

2 Answers
VanReagan
07/24/25 1:15pm
The fog light warning light needs to be cleared with a computer at an authorized 4S dealership. Here is relevant information about automotive fog lights: 1. Classification: Divided into front fog lights and rear fog lights. Front fog lights are typically bright yellow, while rear fog lights are red. The symbols differ slightly - the front fog light symbol has downward light beams, while the rear fog light symbol shows parallel beams. The control is located on the vehicle's dashboard; 2. Purpose: Fog lights enhance visibility during foggy or rainy conditions with poor visibility, making the vehicle more noticeable to others. Therefore, fog light sources need strong penetration capability, with most vehicles using halogen fog lights; 3. Fog light switch: The fog light control has three positions - position 0 turns them off, position 1 controls front fog lights, and position 2 controls rear fog lights.
Was this review help?
14
3
Share
SerenityDella
08/11/25 7:19am
As a long-time car enthusiast, encountering a fog light warning light on my Audi Q7 is a common occurrence—it's mainly the system detecting an issue. Generally speaking, the most common cause is a burnt-out fog light bulb. Just turn on the fog light switch, step out of the car to check if the light is on, and if not, replace the bulb promptly—the light will go off automatically. However, if the warning light persists after replacement, check the fuse in the cabin fuse box (the manual has a location diagram). Replacing it with the correct fuse model usually solves the problem. The Audi Q7's electronic system is quite smart—once the issue is fixed, the light disappears without needing extra tools. If it still doesn’t work, it might be a wiring short circuit or a control module malfunction. Just visit an auto parts store to borrow a diagnostic tool and clear the fault code. Don’t forget to regularly check if the bulb socket has good contact to avoid dust buildup or oxidation causing new issues. Handling it yourself saves money, gives peace of mind, and even expands your knowledge.
Was this review help?
11
2
Share
Expand All
More Forum Discussions

What is China VI?

China VI refers to the National Sixth Stage Emission Standards for Motor Vehicles, which aim to prevent and control environmental pollution caused by exhaust emissions from compression-ignition and gas-fueled spark-ignition engine vehicles. Currently, the China VI standard is divided into two phases: China VIa and China VIb, with plans for nationwide unified implementation. Higher numerical stages indicate stricter standards and relatively lower pollution levels in exhaust emissions. The National Sixth Stage Emission Standards for Motor Vehicles were established to implement environmental protection laws, reduce and prevent vehicle exhaust pollution, protect the ecological environment, and safeguard human health. These standards include emission limits and measurement methods for light-duty vehicles as well as emission limits and measurement methods for heavy-duty diesel vehicles.
2
4
Share

What Are the Reasons for Not Being Able to Engage Reverse Gear in a Manual Transmission?

Reasons for not being able to engage reverse gear in a manual transmission: 1. The clutch is not fully depressed; 2. The gear teeth are just aligned; 3. There is a problem with the transmission. A manual transmission, also known as a stick shift, requires the driver to manually shift gears by moving the gear lever to change the gear engagement inside the transmission, thereby altering the gear ratio to achieve speed changes. In an automatic transmission vehicle, the control system of the automatic transmission selects the appropriate gear based on the engine's speed and load, replacing the driver's subjective judgment and gear-shifting operation. In an automatic transmission vehicle, the R stands for reverse gear. The gear positions in an automatic transmission vehicle, from top to bottom, are: 1. P (Park) for parking; 2. R (Reverse) for reverse gear; 3. N (Neutral) for neutral; 4. D (Drive) for forward gear, with D1 and D2 being specialized gears for long uphill and downhill driving.
14
4
Share

What are the reasons for the ETC display screen not lighting up?

Reasons for the ETC display screen not lighting up: If the ETC light does not turn on or the screen is black, and there is no response when pressing the top button or inserting the ETC card, it may be due to the ETC device being out of power or damaged. In this case, you can take the ETC device and the ETC card to a nearby ETC service center for inspection. If the device is not damaged due to human factors, it can be reactivated or replaced. ETC is an electronic toll collection system that allows vehicles equipped with ETC on-board units to use dedicated ETC lanes. It employs electronic toll collection methods, and the non-stop toll collection system is currently the most advanced road and bridge toll collection method in the world. It uses dedicated short-range communication between the on-board electronic tag installed on the vehicle's windshield and the microwave antenna in the ETC lane at the toll station.
7
4
Share

What does 'view' represent on a car?

On a car, 'view' represents switching the information display interface on the dashboard. Most modern vehicles now use multi-function steering wheels, which allow the operation of various devices, enhancing the driving experience while also making it more convenient for drivers to perform various operations during driving, significantly improving driving safety. Besides this button, 'autohold' is the automatic parking function button; the 'ac' button is the compressor switch, which is the air conditioning cooling switch; the 'sel' key is the menu selection confirmation button, usually found on multi-function steering wheels; the 'ok' key has the exact same function as the 'sel' key; 'mode' is the mode switching button; 'set' on the multi-function steering wheel is the cruise control function button; 'info' stands for the information display function key.
7
1
Share

How to Replace the Air Conditioning Filter in the Second-generation Eado?

The steps to replace the air conditioning filter in the second-generation Eado are as follows: First, open the glove box cover, locate the fixing clips, and pull them outward with force. Use both hands to squeeze the sides of the glove box toward the center, then remove the glove box to reveal the air conditioning filter cover plate. Press the fixing clips on both sides of the cover plate firmly, and the cover plate can be removed. Pull the old air conditioning filter outward, and then reverse the disassembly steps to restore it to its original position. The second-generation Eado features a youthful and sporty appearance with a new family design language. The car's dimensions are 4710mm in length, 1820mm in width, 1505mm in height, and a wheelbase of 2700mm.
3
2
Share

What is the weight of the 2018 Emgrand GL?

2018 Emgrand GL weighs 1320 kg. The body dimensions of the car are 4725mm in length, 1802mm in width, and 1478mm in height, with a wheelbase of 2700mm. In terms of interior, the Emgrand GL continues the aviation-inspired wraparound cockpit design and the family-style arched bridge dashboard design. The control panel adopts a layered integrated center console design, which is very simple and elegant. In detail, the Emgrand GL pays great attention to the embodiment of texture, with brushed metal interior panels and horizontal metal trim across the center console integrated with the streamlined design of the inner door handles, highlighting a sense of refinement in simplicity. In addition, the Emgrand GL also adopts the high central channel design of luxury brand models, which enhances driving safety while further emphasizing the sense of quality.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.