···
Log in / Register

How to Reset the Dashboard Warning Light?

1Answers
MarleyDella
07/29/2025, 09:29:16 PM

You can try starting and turning off the vehicle three times in a row, or disconnect the negative terminal of the engine battery, wait for 30 seconds, reconnect it, and then attempt to start the vehicle. Please note that manual reset is not recommended. Typically, the warning light can only be reset after troubleshooting with a fault detection device at a 4S shop.

Was this review help?
103
Share
More Q&A

What Causes the Windshield Washer to Stop Spraying Water?

There are several reasons why the windshield washer may not spray water, including insufficient washer fluid, incorrect washer fluid selection, or a faulty washer pump. The specific causes are as follows: Insufficient Washer Fluid: If the washer fluid level is too low, the windshield washer will not spray water. Some vehicles have a dashboard warning light that alerts the driver when the washer fluid is low and needs to be refilled. Incorrect Washer Fluid Selection: Choosing the wrong washer fluid can cause it to freeze in cold weather, potentially cracking the washer fluid reservoir. Therefore, it is important to select an antifreeze-type washer fluid based on the local temperature conditions to prevent freezing. Faulty Washer Pump: If the windshield washer pump malfunctions or stops working, it will result in the washer not spraying water.
106
Share

Why is the remaining fuel not displayed on the dashboard?

The dashboard not displaying the remaining fuel is likely due to a faulty fuel gauge. Below are some related introductions about the car dashboard: 1. Speedometer and odometer: The speedometer and odometer are actually composed of two meters. One is the speedometer, and the other is the odometer. Traditional speedometers are mechanical. A typical mechanical odometer is connected to a flexible shaft, which contains a steel cable. The other end of the flexible shaft is connected to a gear in the transmission. The rotation of the gear drives the steel cable to rotate, which in turn drives a magnet inside the odometer cover to rotate. 2. Tachometer: The tachometer is usually located within the instrument panel, placed symmetrically with the speedometer and odometer. The tachometer operates based on magnetic principles, receiving pulse signals generated when the primary current in the ignition coil is interrupted. These signals are then converted into a displayable RPM value. The faster the engine speed, the more pulses the ignition coil generates, resulting in a higher RPM value displayed on the instrument.
120
Share

Can a Privately Owned Vehicle Pass the Annual Inspection After Gas Conversion?

Privately owned vehicles can pass the annual inspection after gas conversion. Below is an extended introduction: Conversion Method: If there is a need to relocate the gas cylinder due to certain reasons, it is entirely possible. Since the service life of a gas cylinder is 15 years, relocation requires a secondary inspection at a gas cylinder testing station. After obtaining a new vehicle gas cylinder usage registration certificate, it can be relocated to a new vehicle for normal use. Insurance Coverage: After a vehicle undergoes "gas conversion," as long as the issue is not related to newly added gas equipment, the insurance company will cover it. At the same time, it is recommended that owners of converted vehicles notify their insurance company to update the policy with an "additional equipment loss rider" to ensure coverage for claims.
103
Share

What procedures are required to replace old license plates with new ones?

The vehicle owner needs to bring their ID card, vehicle registration certificate, and driving license. To replace old car license plates with new ones, the vehicle must be inspected at the vehicle management office. The function of license plates: License plates serve as identification numbers and information registration for vehicles. Their main purpose is to identify the region to which the vehicle belongs, and they can also be used to look up the vehicle's owner and registration details. The plate number changes ownership with the sale of the vehicle until the vehicle is scrapped, at which point the plate number is also retired. Installation of license plates: License plates are plates mounted on the front and rear of the vehicle, typically made of aluminum, sheet metal, plastic, or paper, engraved with the vehicle's registration number, registration region, or other relevant information.
107
Share

What Causes a Car to Stall While Driving Normally?

Reasons for a car suddenly stalling while driving include electrical circuit faults, electrical component failures, and fuel system faults. The specific reasons are as follows: Electrical Circuit Fault: This could be due to a low-voltage power failure while driving, causing the car to stall. In this case, you should primarily check the ignition and starter switch, as well as the fuse box. Electrical Component Failure: This issue is usually related to faults in the ignition coil, capacitor, or electronic ignition module. The car may start initially but stall after a while, then start again, only to stall once more. Fuel System Fault: Possible causes include a damaged fuel pump, ruptured fuel line, clogged carburetor fuel inlet, or an empty fuel tank. In such cases, the car may still be restarted, but with great difficulty.
113
Share

What does 100W on a tire mean?

The meaning of 100W on a tire: 100 is the load index of the tire, corresponding to a maximum load capacity of 800 kilograms per tire; W represents the speed rating of the tire, with W indicating a maximum speed of 270 kilometers per hour. Here are specific details about tires: 1. A tire is a circular elastic rubber product assembled on various vehicles or machinery to roll on the ground. It is usually mounted on metal rims, supporting the vehicle body, cushioning external impacts, achieving contact with the road surface, and ensuring the vehicle's driving performance. 2. Tires are often used under complex and harsh conditions, enduring various deformations, loads, forces, and high and low temperatures during operation. Therefore, they must have high load-bearing performance, traction performance, and cushioning performance. At the same time, they are required to have high wear resistance and flex resistance, as well as low rolling resistance and heat generation. Half of the world's rubber consumption is used for tire production, highlighting the significant rubber consumption by tires.
105
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.