How to Reset the AdBlue Warning Light?

2 Answers
LeonardoRose
07/24/25 12:17pm
The method to reset the AdBlue warning light is quite simple—just refill the diesel exhaust fluid (DEF), commonly known as automotive urea, vehicle urea, or automotive environmental urea. Below are the details related to the AdBlue warning light: 1. Automotive Environmental Urea: AdBlue is a diesel exhaust fluid, also referred to as automotive environmental urea. When the AdBlue warning light appears on the dashboard, it’s necessary to check and replenish the urea. Not all diesel vehicles require automotive urea; only those equipped with Selective Catalytic Reduction (SCR) exhaust after-treatment technology need it. 2. Principle: AdBlue is stored in a urea tank mounted on the chassis. The urea tank supplies the solution to a dosing unit (DU) installed on the chassis. The DU is controlled by the Engine Control Module (ECM). The DU uses compressed air from the vehicle’s system to generate an AdBlue spray, which is delivered to the nozzle in the engine’s exhaust system through a highly precise metering and pumping system.
Was this review help?
2
1
Share
VanAlexa
08/11/25 6:24am
The most common reason for the AdBlue light to come on is low fluid level, so you need to top up the AdBlue solution immediately. This stuff is a special environmental additive for diesel vehicles, used to reduce exhaust pollution. When the light comes on, don't panic—just find an auto repair shop or supermarket to buy a bottle of AdBlue and refill it yourself. It usually has a blue cap, and the filler port is typically located near the fuel tank. After topping it up, start the car and drive a few kilometers, and the light may turn off automatically. If it stays on, it could be a sensor error or the system not resetting—try turning the ignition off and restarting the vehicle. Remember not to mix other liquids when refilling; AdBlue must be pure to avoid clogging the injector. Make it a habit to check the fluid level every 5,000 km and top it up to the maximum mark. If left unresolved for a long time, the car may enter a speed-limiting mode or even fail to start, affecting driving safety. If you can't handle it yourself, visit a dealership—professional equipment can diagnose and fix it quickly.
Was this review help?
16
5
Share
Expand All
More Forum Discussions

What is the correct way to use a car jack?

The correct method for using a car jack is as follows: First, before using the jack, ensure the vehicle is properly parked and place safety warning triangles 50-150 meters behind the car. Then, align the jack with the designated support points under the vehicle's chassis - these contact points should correspond to the manufacturer's marked positions (typically near the side skirts). Finally, connect the provided wrench and socket to the rear of the jack, then rotate directly to adjust the jack's height. Avoid applying excessive force during operation as this may cause deformation of the jack. Note that vehicle jacks are designed only for routine tire changes or suspension inspections, and should never replace proper lift equipment for major repairs. Never place any body parts beneath the vehicle while using a jack. After fully raising the vehicle with the jack, place the spare tire or removed wheel under the car body as a temporary safety measure. This precaution prevents greater damage in case of jack failure.
19
1
Share

What is the correct method to start a Haval H6 automatic transmission car?

After the driver sits in the driver's seat, there is no need to press the brake pedal. Simply press the start button once, and the ACC light will turn on, indicating that the vehicle is performing a self-check. Press the brake pedal and then press the start button again to ignite and start the engine. Under normal circumstances, the engine will start within 3 seconds of pressing the ignition switch. Release the foot brake, and you can choose to warm up the car in place. The duration can be adjusted according to the environment. Specifically, you can refer to the water temperature gauge on the dashboard. Press the foot brake again, shift to D gear, and release the handbrake (for electronic handbrakes, simply press the button briefly). Before starting, ensure you clearly observe the road conditions through the rearview mirror.
7
1
Share

What are the steps to drive an automatic transmission car?

Before starting the car, familiarize yourself with the functions of the buttons inside the car, which are usually introduced in the manual. They are mainly divided into steering wheel function buttons and the positions of the brake and accelerator at the bottom. First, press the one-touch start button marked with 'start', located at the top left corner of the gear shift; press once for ACC, and press twice for all dashboard indicator lights to turn on. After confirming the car is in good condition, use your right foot to press the brake, then press the one-touch start button to ignite and start the car; continue to press the brake with your foot and shift the gear to D (Drive). Press down the (P) button for the electronic parking brake, then slowly release the foot brake with your right foot, and the car will start moving forward; press the accelerator on the right with your right foot to accelerate the car.
11
0
Share

What Causes the Rear Windshield to Shatter for No Reason?

The reason for the rear windshield shattering for no apparent reason is due to excessive internal air pressure. Below are relevant details about windshields: Functions of Windshields: They are categorized into laminated glass, tempered glass, and zoned tempered glass. Laminated glass combines the toughness of plastic with the hardness of glass, enhancing the glass's resistance to breakage. Tempered glass, upon impact, shatters into small, blunt-edged fragments, minimizing harm to passengers. Zoned tempered glass undergoes special treatment to maintain some clarity in its cracks when shattered upon impact, ensuring the driver's field of vision remains unobstructed. Maintenance of Windshields: Use windshield washer fluid appropriately. During regular windshield maintenance, select suitable washer fluid based on the season and weather conditions. When the windshield surface appears blurry, cleaning it with the right washer fluid can restore clarity. If the glass reflects light irregularly at night, it can also be wiped with washer fluid. Additionally, during highway driving or in dusty conditions, washer fluid is consumed quickly, so it's important to replenish it promptly.
2
0
Share

What Causes Rear Tire Wear?

Rear tire wear can be caused by incorrect tire pressure (either too high or too low), frequent overloading, incorrect wheel camber leading to excessive sidewall contact with the road surface, or inaccurate wheel alignment. Below is relevant information about tires: Purchase tips: When selecting tires, pay attention to the speed rating, load index, manufacturing date, and size. Avoid purchasing tires manufactured more than three years ago, as unused tires deteriorate over time. Timely replacement: Replace tires every four years, even with minimal mileage. Since tires are rubber products that degrade with age, prolonged use without replacement poses safety risks.
6
0
Share

What Causes the Squeaking Sound When Applying Rear Drum Brakes?

Rear drum brakes making a squeaking sound when applied may indicate severely worn brake pads that need replacement. Below is relevant information about brakes: Drum Brakes: Inside the wheel hub, two semi-circular brake shoes are installed. Using the "lever principle," the brake shoes are pushed to make contact with the inner surface of the hub, creating sufficient friction to reduce the wheel's rotation speed and achieve braking. Disc Brakes: A brake caliper controls two brake pads to clamp onto the brake disc attached to the wheel. When the brake pads grip the disc, friction is generated between them to reduce the wheel's rotation speed, allowing the car to slow down or stop.
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.