How to Replace the Remote Battery for Trumpchi GS4?

[OLeah]

To replace the remote battery for Trumpchi GS4, follow these steps: Use a small flat-head screwdriver to pry open the remote shell, then you can see the battery. Remove the old battery and replace it with a new one. The dimensions of the Trumpchi GS4 are 4545mm in length, 1856mm in width, and 1668mm in height, with a wheelbase of 2680mm and a fuel tank capacity of 55 liters. The Trumpchi GS4 is equipped with a 1.5T turbocharged engine and a 6-speed manual transmission, delivering a maximum power of 124 kW at 5000 rpm and a maximum torque of 265 N·m between 1700 to 4000 rpm.

[DiMia]

I've been using the Trumpchi GS4 for three years, and recently the remote key keeps failing—it's definitely a dead battery. Changing the battery yourself is quite simple: there's usually a small gap or screw hole on the back of the key. At home, I use a coin or a small Phillips screwdriver to gently pry or unscrew it. After opening, you'll see a small round battery compartment with a CR2032 coin battery inside. Remember to buy the same model of battery from a supermarket or online, and don't put it in backwards—the positive side should face up. After placing the new battery, carefully close the key cover and press the button to test it. If the car lights up or the door responds, you've succeeded. The whole process takes less than ten minutes, saving both money and effort, and avoids the awkwardness of not being able to find a repair shop in time.

[Joann]

As an automotive enthusiast, I've disassembled the GAC GS4 key fob to replace the battery several times. The method involves using small tools like nail clippers or a micro screwdriver to carefully pry open the key fob from the edge gap. Inside, you'll find a CR2032 battery – this 3V model is quite durable. When removing the old battery, check the contacts for any corrosion; if present, clean them gently with a cotton swab. When installing the new battery, ensure proper polarity alignment and avoid applying excessive pressure to prevent short circuits. After reassembly, test the remote function from a few meters away to confirm it's working again. These batteries are readily available at electronics stores, making the process hassle-free while also allowing you to pick up some handy skills.

[Noelle]

As a new car owner, I was a bit nervous about changing the remote battery for the first time, but the process is actually quite simple. First, prepare a new CR2032 battery, which can be easily purchased at a convenience store. Look for a small slot or notch on the back of the key, and gently pry open the cover using a coin. Remove the old battery, making sure to note its position to avoid mixing up the positive and negative sides. After inserting the new battery, gently close the cover. Finally, press the button to test it—once the car responds, you're good to go. The whole process takes just a few minutes and is very easy to master.

[JasonDella]

Changing the battery for your Trumpchi GS4 remote is a breeze! Just get a CR2032 battery, which is cheap and easy to order online. Use a coin to pry open the key from the side seam, revealing the battery slot. Remove the old battery, insert the new one with the positive side facing up, and snap the cover back into place. Test the remote's response afterward to avoid unnecessary trips to the dealership and save money. So convenient!

[Briana]

I often help friends fix this kind of issue. Be careful not to damage the key when replacing the remote battery. The Trumpchi GS4 key might have hidden screws; using a small screwdriver to unscrew them makes disassembly easier. If the CR2032 battery is placed backwards, it may malfunction. Remove the old battery and check for any leakage or corrosion on the contacts. After installing the new battery, walk a few steps away to test if the functions work properly before locking the car. Remote batteries typically need replacement every two years, and proper maintenance can extend the key's lifespan.