How to Replace the Crown Steering Gear?

How to Remove the Rear Seats of the Tayron?

The method to remove the rear seats of the Tayron is as follows: 1. Place your hands under the seat cushion and lift it upward; 2. Flip the lifted seat cushion forward; 3. Push the connecting shafts on both ends toward the middle to release the iron shafts from the slots. The Tayron is a mid-size 5-door, 5-seat SUV with the following dimensions: length 4589mm, width 1860mm, height 1660mm, and a wheelbase of 2731mm. It has a fuel tank capacity of 60 liters. The Tayron is equipped with a 1.4T turbocharged engine and a 7-speed dual-clutch transmission, delivering a maximum power of 110 kW at 5000 to 6000 rpm and a maximum torque of 250 Nm at 1750 to 3000 rpm. It features front-wheel drive, with a front suspension using MacPherson struts and a rear suspension employing a multi-link independent setup.

3

2

Share

What to Do When the Display Screen Stays On After the Car Is Turned Off?

If the display screen remains on after the car is turned off, use an automotive diagnostic tool to access the system and read the data stream. It is likely due to an issue with the power supply module of the display screen, which requires timely inspection and repair. If you are not familiar with the operation process, it is best to take it to a repair shop for professional handling. The dashboard mainly consists of an odometer, speedometer, engine tachometer, fuel gauge, water temperature gauge, oil pressure gauge, warning lights, and indicator lights. Below are the contents of the dashboard display screen: 1. Basic components: Tachometer, turn signal indicator, coolant temperature gauge, fuel level, speedometer with odometer, adjustment and test buttons, indicator lights or driver information system, trip meter reset button. 2. Indicator lights: EPC (Engine Power Control) indicator, Audi A3 exhaust monitoring system indicator, Audi A3 Electronic Stability Program (ESP) indicator, Audi A3 generator fault indicator, Audi A3 seat belt indicator, Audi A3 fuel tank system indicator.

7

1

Share

What is the normal tire pressure for Ora cars?

The normal tire pressure for Ora cars is generally between 2.2-2.5 bar. In winter, the tire pressure should be adjusted slightly higher by about 0.2 bar based on the standard tire pressure. In summer, it is advisable to maintain the tire pressure at the lower limit of the standard range, for example, 2.4 bar for standard tires. If the car is often parked outdoors, the tire pressure can be slightly lower than the standard by about 0.1 bar to prevent tire blowouts due to high temperatures. Hazards of overinflated tires: Reduced friction and adhesion of the tires, affecting braking performance; Causes steering wheel vibration and deviation, reducing driving comfort; Accelerates wear on the central tread pattern, shortening tire lifespan; Increases body vibration, indirectly affecting the lifespan of other components; Causes excessive stretching and deformation of tire cords, reducing tire elasticity and increasing the load on the car while driving; Decreases puncture resistance. When encountering sharp objects like nails or glass on the road, the tire is more likely to be punctured, leading to internal cracks, blowouts, and potential tire bursts. Hazards of underinflated tires: Increases friction with the road surface, leading to higher fuel consumption; Causes heavy steering and deviation, posing safety risks; Increases movement of tire components, leading to abnormal heat due to excessive rolling; Reduces the functionality of cords and rubber, causing delamination or cord breakage and excessive friction with the rim, leading to damage and abnormal wear at the bead area; Multiplies friction between the tire and the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving under these conditions can lead to tire bursts; Increases tire deformation, leading to cracks on the tire sidewalls and excessive heat generation due to flexing, accelerating rubber aging, cord fatigue, and breakage. It also increases the tire's contact area with the ground, accelerating shoulder wear.

3

0

Share

What to Do If the Santana Key Is Lost?

Santana 2000 and Santana 2000GSI (Superman) models come with three keys and one key tag. Among them, two are master keys that can open all locks on the vehicle. The third is a sub-key, which can open all locks except for the trunk and glove box. If a key is lost, you can use the spare key and then have a new key made using the key tag. Below is relevant information about the Santana 2000 keys: 1. Key Tag: Particularly for the Santana 2000GSI model, the key tag contains the key's tooth shape number, the anti-theft system control unit's identification code, and password. If the master or sub-key is lost, you should immediately take the key tag to an authorized Shanghai Volkswagen service station to have a new key made and matched. This process also renders the lost key's code invalid, but the new key must be matched by the service station before it can be used normally. 2. Magnetic Chip System: Each vehicle has its own unique chip, similar to a human ID card, which is part of the magnetic chip system. The car's ignition lock cylinder's reading coil will read the key's chip. Each chip has fixed digital information.

1

2

Share

What Causes the Engine Warning Light to Illuminate in a Nissan Sylphy?

There are primarily 7 reasons for the engine warning light to illuminate: Sensor malfunction: The sensors mentioned here include coolant temperature, crankshaft position, air flow, intake temperature, oxygen sensors, etc. When these sensors are damaged, have poor contact, or experience signal interruption, the vehicle's ECU cannot accurately obtain engine data, which triggers the engine warning light. Fuel or oil quality issues: If fuel or engine oil is not added as per the manufacturer's requirements, it may cause engine wear, leading to the illumination of the warning light. Poor combustion of the air-fuel mixture: Poor combustion can result in engine carbon buildup or knocking. When detected by the oxygen sensor and reported to the ECU, the warning light will illuminate as a warning. Issues such as faulty spark plugs, ignition coils, fuel pump, or clogged fuel lines can cause poor combustion of the air-fuel mixture. Turbocharging problems: The intake turbocharging pipeline or turbocharger can also cause the engine warning light to illuminate. The most common issue is turbocharger damage, accompanied by symptoms like oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake problems: If there are issues with the vehicle's air intake, it may lead to engine pipeline blockages, and in severe cases, the engine warning light will illuminate. A dirty air filter that hasn't been cleaned regularly can cause intake problems. Exhaust problems: Exhaust faults can also trigger the engine warning light. Causes include faulty rear oxygen sensors, catalytic converter, exhaust camshaft, or bearings, with the catalytic converter being the most common issue. Using leaded gasoline, lead or silicon-based lubricant additives, physical damage to the catalytic converter, or fuel system malfunctions can easily cause catalytic converter failure. Anti-theft system malfunction: If the vehicle's electronic anti-theft system malfunctions or if the anti-theft controller is incompatible with the engine electronic controller, the anti-theft system can prevent the engine from operating normally, accompanied by the illumination of the engine warning light. If the engine warning light is on, follow these steps: First, check if the engine is running normally and whether there are issues like shaking or black smoke. If so, avoid restarting the engine. Note: Do not restart the engine if the red warning light is on. If the engine can start, turn it off for 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'on' position without depressing the clutch. The vehicle will perform a self-check after powering on. Wait 5-10 seconds to see if the warning light turns off. If the warning light remains on, visit a service center as soon as possible. The service center can use a portable diagnostic tool to read the fault code, identify the issue, and perform targeted repairs.

8

1

Share

What is the battery model for the Peugeot 408 key?

The battery model is CR2032. It is a lithium manganese dioxide battery, named according to the IEC standard. Among them: C- indicates a chemical battery system with lithium metal as the negative electrode and manganese dioxide as the positive electrode; R- indicates that the battery is cylindrical in shape, with F replacing it if it is square; 20 indicates that the battery has a diameter of 20mm; 32 represents a battery height of 3.2mm. The nominal voltage is 3.0V, the endpoint voltage is 2.0V, and the rated capacity is approximately 200mAh. CR2032 typically has a lifespan of 5 years. If the manufacturer's production level is not high or quality control is poor, its lifespan will be significantly shortened. Domestic first-tier brand batteries can generally guarantee this lifespan. If the usage environment is ideal (sealed, room temperature, free from moisture, etc.), its lifespan can be further extended to 8 years or even 10 years. The usage time of a vehicle remote key battery is closely related to the frequency of use. The more frequently it is used, the shorter the usage time will be. If the remote key battery runs out of power, the mechanical key can be used directly to open and start the vehicle. The batteries used in car remote keys are button batteries, mainly including models: CR2016, CR2025, CR2032, and CR2450. For the specific model used in each key, owners can refer to the battery model in the user manual for replacement. Button-type CR2016 battery: The usage rate of car key remotes is very high, making it one of the most common remote battery types. The voltage of this battery is 3V, while most car key batteries are powered by 9V, so all three batteries need to be replaced each time. Examples include Guangben, Toyota, Volkswagen, Mazda, etc. CR2016 specifications: battery diameter 20mm, thickness 1.6mm. Button-type CR2025 battery: Its usage rate is much lower than CR2016. However, it is still used in some car keys. It is thicker than the 2016 model but has a relatively higher storage capacity. CR2025 specifications: battery diameter 20mm, thickness 2.5mm. This type of battery is also commonly used in audio remotes. Button battery CR2032: Its thickness is twice that of CR2016. The 3V-CR2032 lithium manganese battery belongs to the lithium-manganese dioxide structure. The positive electrode material is chemically very stable manganese dioxide, the negative electrode material is metallic lithium, and the electrolyte is a lithium battery. The main components of the electrolyte are ethylene glycol dimethyl ether, propylene carbonate, and lithium perchlorate. Its shape resembles a button, hence it is referred to as a button lithium battery or lithium manganese button battery. Button battery CR2450: Compared to the other three models, it is thicker and larger, with a diameter of 24.5mm and a height of 5.0mm. The rated current value of CR2450 is 0.2mA, mainly used in low-power electronic products. Generally, the battery can provide an output current of 0.001mA to 5mA, with a continuous output current of up to 15mA and a flash output current of up to 30mA, meeting the requirements of most small electronic products for light emission, sound production, and RF output.

6

3

Share

How to Replace the Crown Steering Gear?

How to Remove the Rear Seats of the Tayron?

What to Do When the Display Screen Stays On After the Car Is Turned Off?

What is the normal tire pressure for Ora cars?

What to Do If the Santana Key Is Lost?

What Causes the Engine Warning Light to Illuminate in a Nissan Sylphy?

What is the battery model for the Peugeot 408 key?

What is the Injection Advance Angle?

How Long Does a Remote Key Battery Last?

What is the reason for the noise when reversing a Hyundai Elantra?

How to Use the Binyue Electronic Parking Brake?