How to Replace the Brake Light on Changan CS35?

[DeAlejandro]

Method for replacing the brake light on Changan CS35: 1. Empty the trunk and lift the mat above the spare tire, then remove a total of eleven self-tapping rivets on the left, right, and middle sides; 2. Remove the plastic panel below the trunk lid and the felt panels on both sides; 3. After removing the felt panels, lift off the plastic panel; 4. Remove the lamp socket and replace the brake light bulb to complete the replacement. Taking the 2017 Changan CS35 as an example, its body dimensions are 4170mm in length, 1810mm in width, and 1670mm in height, with a wheelbase of 2560mm, a minimum ground clearance of 180mm, and a fuel tank capacity of 52 liters. This car is equipped with a 1.6L naturally aspirated engine, with a maximum power of 92kW and a maximum torque of 160Nm, paired with a 5-speed manual transmission.

[LeZoe]

As a Changan CS35 owner, I've changed the brake lights a few times and found it quite straightforward. First, gather the necessary tools—basically just a Phillips screwdriver and the bulb (usually W16W or 1156, but best to check the manual for confirmation). Open the trunk, locate the tail light cover panel, and use the screwdriver to remove a few screws before gently prying off the cover—be careful not to apply too much force to avoid scratching the paint. Then, remove the old bulb and check if the filament is broken. When installing the new bulb, avoid touching the glass part, as oil from your hands can shorten its lifespan. Before reassembling, test it: start the car and press the brake pedal to see if it lights up. If the bulb model is incorrect or the cover isn’t secured properly, you might have to redo it. Last time, I didn’t insert the bulb firmly enough—it lit briefly and then went out, taking me a while to fix it. A reminder: always remove the key before changing the bulb to prevent short circuits, and keeping gloves handy helps avoid dirty hands. Regularly checking your brake lights can prevent rear-end collisions—safety first, and it saves you a trip to the repair shop.

[SanMaddox]

I was a bit nervous the first time I changed the brake light on my Changan CS35, being a newbie at this. First, I bought a pair of bulbs (model 1156) on Taobao for less than twenty yuan. After opening the trunk, I located the round brake light cover and loosened the fixing screws with the included screwdriver. I had to be careful during removal—the plastic cover is quite brittle, and I almost cracked it. After taking out the old bulb, I confirmed it was burnt out and quickly replaced it with a new one, making sure the bulb's base was aligned and securely inserted into the slot—inserting it the wrong way wouldn't work. For testing, I had my wife press the brake pedal while I watched the light to confirm it was working before reassembling everything. During the process, I remembered to wear gloves for protection and avoid getting hand oils on the bulb, which could affect heat dissipation. After finishing, I felt a great sense of accomplishment and even took the opportunity to teach my child some basic car knowledge. Next time, I plan to check the lights every six months to avoid any nighttime driving issues that could compromise safety.

[ElliottRose]

I believe the key to replacing the brake light on a Changan CS35 lies in identifying the correct model and proper disassembly. The model is usually referenced in the manual as 1156 or W16W. First, open the trunk to locate the brake light assembly, then use a Phillips screwdriver to remove the screws. Be gentle when removing the light cover to avoid damaging the wiring harness. Before installing the new bulb, clean the socket to ensure good contact and prevent fuse blowouts. After completion, test the functionality to avoid improper installation. It's cost-effective and efficient, and I recommend regular maintenance to enhance driving safety.

[GideonLee]

Replacing the brake light on a Changan CS35, as a family car user, I prioritize simplicity and safety. The steps are straightforward: open the trunk to locate the light cover, remove the screws; carefully take out the bulb to confirm it's burnt out, then replace it with a new bulb of the same model (commonly 1156 type); reinstall and test the light. Safety reminder: disconnect the car key during replacement to prevent short circuits, opt for LED versions for longer lifespan but avoid exceeding voltage limits. It's recommended to inspect quarterly to ensure nighttime driving safety and prevent rear-end collisions.

[JosephineFitz]

I saved a lot of money by replacing the brake light on my Changan CS35 myself. All I needed was a screwdriver and a new bulb (model 1156, purchased online for about ten yuan). The process was very simple: open the trunk to locate the light cover, unscrew and remove it; gently pry it open, compare the old bulb with the new one for replacement, and ensure the insertion direction is correct; then reinstall and test to confirm it works. DIY saved me hundreds of yuan in labor costs at the 4S shop, and I also learned some skills—why not? Regular maintenance is key; don’t wait until you’re on the road to discover problems.