How to Replace the Battery in an MG Car Remote?

2 Answers
CarmenRose
07/28/25 9:41pm
Here are the steps to replace the battery in an MG car remote: 1. Pry open the back cover with force. Press and push the button battery forward to remove it. 2. Place the new battery into the circular slot and ensure it is fully secured into the tail slot to guarantee proper and complete contact with the circuit board. 3. Reattach the back cover of the remote key and press firmly. Check that the gaps around the edges are even. Here are some precautions: 1. Do not place the car smart key near electronic devices. Frequently keeping the smart key and mobile phone together may cause malfunction, as the chip inside the smart key can sometimes be interfered with by the phone's frequency, leading to temporary failure of the remote function. 2. Avoid rough handling. If the smart key gets wet, do not shake it vigorously, as this may cause water to seep into other critical circuits. Also, avoid immediately using the remote to unlock the car, as this could burn out the circuit board.
Was this review help?
11
4
Share
AsherMarie
08/12/25 2:17am
I recently replaced the battery in my MG car remote, and the process was quite simple. First, look at the back of the remote—there’s usually a small gap or screw hole. Use a thin plastic tool or a small screwdriver to gently pry open the casing, but avoid using too much force to prevent damage. Once opened, you’ll see a round coin-cell battery, typically a CR2032. Note the positive and negative orientation, as the old battery might be loose and easy to remove. Align the new battery properly, ensuring it sits flat without tilting. Press the casing firmly when closing it, then test the remote by pressing a button to check if the key light turns on or if the locking function works. If you’re unsure about the battery model, check the number on the old battery and buy the same one—they’re usually available at supermarkets or auto parts stores. Handling this small task yourself saves time and money, but if the casing is too tight, don’t force it; it’s safer to have it replaced professionally for a small fee.
Was this review help?
13
4
Share
Expand All
More Forum Discussions

How much fuel does a diesel car consume when idling with the AC on for one hour?

There is some variation depending on the vehicle model, but for household cars, it is generally between 1L to 3L of fuel per hour. Relevant information about idling is as follows: 1. Introduction one: Idling refers to the operation of the engine without any load, only overcoming the friction resistance of its internal components, without delivering power externally. The minimum speed required to maintain stable engine operation is called idling, which is one of the five basic operating conditions of an engine. 2. Introduction two: When adjusting the idle speed, the RPM should not fluctuate abruptly, as it can cause early wear to the engine. If you rest in the car with the AC on for a long time, especially in recirculation mode, the air quality inside the car will become increasingly polluted, and harmful gases will gradually accumulate, posing health risks and even life-threatening dangers. Please be cautious.
7
5
Share

What are the points deducted for parallel parking?

Subject 2 parallel parking deduction points include stopping midway, stalling, and the car crossing the line after reversing, etc. The passing score for Subject 2 is 80 points, and a score below 80 is considered a fail. Candidates need to wait for a period before scheduling a retest, with the number of attempts not exceeding five. Relevant information about the driving test is as follows: 1. Introduction one: The driving license test is an examination to obtain a motor vehicle driving license. The test content and passing standards are unified nationwide, generally divided into four test subjects: theoretical knowledge test, field driving performance test, road driving performance test, and civilized driving-related knowledge. 2. Introduction two: Subject 2 is the field driving skills test, including 16 test contents such as reversing into a garage and parallel parking. After passing all four subjects, one can obtain a motor vehicle driving license. Individuals aged 18 and above can take the test. Subject 2 generally requires a cumulative total of 26 study hours, including 2 hours of theoretical knowledge and 24 hours of practical operation. Only after completing the required study hours can one schedule the test.
4
1
Share

How to Obtain the License Plate Quota After Selling a Car?

After selling a passenger car, once the buyer completes the license plate registration and the vehicle is transferred out of the local area (after the file transfer), the vehicle management office will upload the sale record to the passenger car quota website within 3 working days at the latest. After the upload, you can apply for the quota on the passenger car website. The quota cannot be used on the same day it is generated. To apply for the reuse of the original license plate number, the following conditions must be met: 1. Condition 1: The application must be submitted within six months after the transfer or cancellation of registration. 2. Condition 2: The original owner must have owned the vehicle for more than three years. 3. Condition 3: All traffic violations and accident records related to the original vehicle must be resolved.
18
0
Share

Where can I adjust the excessive door gap?

If the car door gap is too large, you can directly go to a 4S shop and have the staff inspect and adjust the door. The car door consists of the outer door panel, inner door panel, door window frame, door glass guide rail, door hinge, door lock, and window accessories. The following are the design requirements for car doors: 1. Ensure passenger convenience when getting on and off, with the maximum opening angle controlled at around 65° to 70°. 2. During the opening process, there should be no interference with other parts. 3. When the door is closed, it should lock reliably and not open by itself while driving. 4. The door mechanism should be easy to operate, including smooth closing and easy window lifting. 5. Good sealing performance is required. 6. A large transparent area is needed to meet lateral visibility requirements. 7. Sufficient strength and rigidity are necessary to ensure reliable door operation, reduce door vibration, improve vehicle side collision safety, and prevent door sagging. 8. Good manufacturability and assembly process for the door.
18
5
Share

Why is the LSY engine considered untouchable?

LSY is currently one of General Motors' most mainstream engines, boasting very high technological sophistication. However, it falls short of the LTG in terms of power and lacks the mid-to-high-speed explosive power of the LTG. Additionally, during cylinder deactivation, the operation is not as smooth as the LTG due to the added cylinder deactivation mechanism. Nevertheless, the LSY offers better fuel economy than the LTG, with more advanced technology and more linear power output. More details are as follows: 1. Tripower Valve Management Technology: The LSY engine can control the valves to achieve special opening degrees during operation. In four-cylinder operation mode, the intake valves are fully open during the intake stroke, and the air intake is normal, so the fuel injection follows the standard air-fuel ratio (14.7:1). This mode delivers a good performance experience, thanks to its maximum power reserve of 177kW/350Nm (1500~4000rpm). 2. Intelligent Cylinder Deactivation Technology: The LSY engine's crankshaft structure is also very unique. Under the control system's command, it can shut down the operation of cylinders 2 and 3, leaving only cylinders 1 and 4 working in a "half-open valve" state. Theoretically, fuel consumption is halved, though the power output in two-cylinder mode is somewhat reduced, leading to a slight increase in operating RPM. Nonetheless, the overall fuel-saving effect remains quite impressive.
1
1
Share

What to Do When the Auto Start-Stop System Fails in the Envision?

The auto start-stop system failure in the Envision requires timely battery recharge. Below are more details about the auto start-stop system failure in the Envision: 1. Cause: The auto start-stop system failure in the Envision is due to insufficient battery charge or the need for battery replacement. 2. Insufficient Charge: Many vehicles are equipped with an auto start-stop system, which requires sufficient battery charge to function properly. If the battery charge is insufficient, the auto start-stop system will not work correctly. Additional Information: As General Motors' new-generation global strategic model, the Envision's exterior design inherits the essence of the ENVISION Vision concept car, featuring a newly designed intelligent drag-reducing grille, aluminum roof rails, newly styled chrome dual exhaust pipes, 19-inch multi-spoke aluminum alloy wheels, and multi-function exterior rearview mirrors.
15
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.