How to Replace the Battery in a Hyundai Mistra Remote Key?

What is the battery model of Wuling Zhiguang?

The battery model of Wuling Zhiguang is 12V-48AH-450A. The detailed specifications are: rated voltage of 12V, 48AH, 20-hour rate nominal capacity of 60AH, and cold cranking amperage (CCA) of 450A (SAE standard). The working current of Wuling Zhiguang's battery depends on its model (capacity), which is marked on the casing. Higher working currents result in shorter operation times. Below are usage precautions for Wuling Zhiguang's battery: 1. Neglecting to turn off electrical circuits may drain the battery. In extremely cold winter temperatures, prolonged vehicle inactivity, or when the battery is nearing the end of its lifespan, this could prevent the car from starting. 2. Solution for dead battery: Connect the charged battery of another vehicle to your car's battery terminals (positive to positive, negative to negative) using jumper cables to power the electrical system and start the engine. Ensure correct polarity to avoid reverse connection.

15

1

Share

How to Replace the Cabin Air Filter of Haval H2?

Haval H2 cabin air filter replacement steps are: 1. The cabin air filter is located inside the glove compartment on the passenger side. Open the glove compartment, pinch the small pull rod at the bottom right corner, and remove the pull rod; 2. Apply force to the top left corner by pressing it to the right, and the left side will pop out. The same applies to the right side; 3. After removing the glove compartment, you will see the clips on both sides of the cabin air filter. Gently pull the filter out from both sides simultaneously; 4. Align the new filter box correctly and gently push it into place. The dimensions of the Haval H2 are 4330mm in length, 1815mm in width, and 1700mm in height. The vehicle is powered by a 1.5T turbocharged engine, paired with a 7DCT Getrag wet dual-clutch transmission, delivering a maximum power of 110kW and a peak torque of 210Nm.

18

5

Share

Why Does an Engine Misfire?

Engine misfiring can be caused by: 1. Severe burning of the contacts in the distributor cap of the ignition system, leading to spark jumping; 2. The ignition coil failing to produce high voltage; 3. Reduced radial width and weakened elasticity of the piston rings; 4. Excessive carbon buildup on the spark plugs; 5. Carbon accumulation in the fuel injector, clogged injector filter screen, resulting in imprecise injection and atomization. Symptoms of engine misfiring include: 1. Noticeable body vibration at idle; 2. Obvious intermittent exhaust flow with severe shaking of the exhaust pipe; 3. Significant body vibration at low RPMs around 2000, accompanied by weak acceleration, with reduced vibration sensation at higher RPMs.

12

1

Share

What Causes Engine Vibration?

Engine vibration can be caused by: 1. One or more cylinders not functioning properly in the engine; 2. Worn-out or loose engine mounts; 3. Excessive carbon buildup in cylinders, throttle body, spark plugs, or intake system; 4. Partial blockage in fuel tank switch, fuel filter, or fuel lines between tank and carburetor; 5. Leaks in intake manifold or EGR valve; 6. Malfunctioning intake pressure sensor or mass airflow sensor. For engine maintenance, pay attention to: 1. Regular oil and oil filter changes; 2. Maintaining good crankcase ventilation; 3. Periodic crankcase cleaning; 4. Regular fuel system cleaning; 5. Routine radiator maintenance; 6. Fuel system cleaning.

5

0

Share

What brand is a car with a 'Z' logo?

A car with a 'Z' logo is from the Zotye brand. Its models include the T600, T800, T700, T500, T300, etc. Taking the T600 as an example, the car's dimensions are 4676mm in length, 1893mm in width, and 1696mm in height. The interior features a flat-bottom multifunction steering wheel, a floating central control screen, and a touch-screen air conditioning panel. The T800 has dimensions of 4910mm in length, 1933mm in width, and 1735mm in height, with a wheelbase of 2850mm. The car comes standard with ABS and EBD, ESP, TCS traction control system, driver status monitoring, run-flat tires, cruise control, and other intelligent configurations.

12

2

Share

Where to Install the Door Anti-Collision Strip?

The door anti-collision strip is installed on the most protruding part of the side door. Made of rubber or natural rubber, the car anti-collision strip is an exterior trim designed primarily to prevent minor scratches and damage to parts. Installing an anti-collision strip does not fall under the category of car modification and will not affect the normal annual inspection of the vehicle. However, when purchasing an anti-collision strip, it is advisable to choose one that matches the color of the car body to maintain the vehicle's overall harmony. The main purpose of installing a door anti-collision strip is to prevent door scratches. It has a certain elasticity, providing protection and enhancing the car's lines and dynamism. There are band-type anti-collision strips with a U-shaped cross-section, featuring double-sided tape on the inner side of the U. To install, simply insert the U-shaped groove into the edge of the door.

13

0

Share

How to Replace the Battery in a Hyundai Mistra Remote Key?

What is the battery model of Wuling Zhiguang?

How to Replace the Cabin Air Filter of Haval H2?

Why Does an Engine Misfire?

What Causes Engine Vibration?

What brand is a car with a 'Z' logo?

Where to Install the Door Anti-Collision Strip?

What is the battery model for Toyota Corolla?

Is the Sharan an imported vehicle?

What is the matching method for the Zhijun remote control?

Where is the windshield washer fluid reservoir located?