···
Log in / Register

How to remove the spare tire of Wuling Hongguang Plus?

3 Answers
OAnthony
07/24/25 10:36pm
Pull the trunk switch located on the left side of the driver's leg area to lift and open the trunk. Lift the floor panel to locate the spare tire, then unscrew the central removal bolt to take out the spare tire. Below are potential safety hazards associated with spare tires: 1. Unsafe for prolonged use: Spare tires and original tires have different production dates, leading to variations in aging, hardening degree, lifespan, and deformation. Therefore, prolonged use is unsafe. After emergency use, the spare tire should be promptly replaced with an original factory tire. 2. Limited to emergency use: Regardless of width, spare tires have special production and usage requirements from manufacturers. Since spare tires are not routinely mounted on vehicles and lack wear, their usage inherently carries certain safety risks. 3. Not suitable for tire rotation: Authorized dealerships impose strict requirements on original tire rotation, and spare tires are particularly unsuitable for rotation. Tire rotation aims to balance wear across different positions, but current practices discourage left-right rotation, and front-rear rotation also presents uneven wear issues.
Was this review help?
19
0
Share
LeRonan
08/10/25 10:13am
I've been driving the Wuling Hongguang Plus for several years, and removing the spare tire is actually quite simple—it's hidden under the trunk. First, clear out any clutter in the trunk and lift the floor panel to reveal the spare tire secured by a circular retaining ring. Use the wrench from the onboard tool kit to turn the screw on the retaining ring counterclockwise; a few turns will loosen it. Remember, the spare tire is quite heavy, so it's best to lift it with two people to avoid straining your back. After removal, check the tire pressure and tread wear. For frequent drivers, I recommend inspecting the spare tire every six months to avoid issues when you urgently need it next time. Don’t overlook it during routine maintenance—spare tires can degrade over time, affecting driving safety. Before long trips, I always give mine a quick check to avoid hassle on the road. In short, as long as you’re somewhat handy, it’s no trouble at all.
Was this review help?
11
3
Share
Expand All
VanFinley
09/26/25 6:25am
Many car owners have asked about this. The spare tire of the Wuling Hongguang Plus is usually fixed under the trunk floor. Just lift the floor mat to find it. Use the wrench that comes with the car to align with the screws on the fixing plate, turn it counterclockwise a few times to loosen, and then steadily pull out the spare tire. Beginners often apply too much force and get the screws stuck, so remember to be gentle. Another common issue is the tool not being properly aligned, causing it to slip and potentially damage the car paint, which can be a big problem. Make sure the car is parked on level ground and the handbrake is engaged to prevent rolling. After removing the spare tire, don’t just leave it in the car. I’ve seen many car owners forget to close the trunk or have items damage it, so it’s best to place it in a shaded area and check for tread cracks. For those who frequently drive on dirt roads, the spare tire is more prone to dust accumulation and rust. It’s recommended to lubricate the fixing points quarterly to extend its lifespan. Safety first is the golden rule.
Was this review help?
16
5
Share
Expand All
More Forum Discussions

Is Audi Original Glass Better or Coated Glass Better?

Choosing coated glass is better. Coated glass offers many color options for the coating, and since the glass coating is applied to the 2nd and 3rd surfaces of the insulated glass, it ensures excellent durability of the coating. Additionally, selecting low-e coated glass can effectively prevent UV damage and more. Introduction to Coated Glass: Coated glass (Coated glass) is also known as reflective glass. Coated glass involves applying one or more layers of metal, alloy, or metal compound films on the glass surface to alter its optical properties and meet specific requirements. Depending on the product's characteristics, coated glass can be categorized into the following types: heat-reflective glass, low-emissivity glass (Low-E), conductive film glass, etc. Production Methods of Coated Glass: There are many production methods for coated glass, mainly including vacuum magnetron sputtering, vacuum evaporation, chemical vapor deposition, and sol-gel methods. Magnetron sputtering coated glass utilizes magnetron sputtering technology to design and manufacture complex multi-layer film systems, allowing for a variety of colors on white glass substrates. The film layers exhibit good corrosion resistance and wear resistance, making it one of the most widely produced and used products currently.
19
0
Share

What is the fuel consumption of the new Bora?

According to the test by the Ministry of Industry and Information Technology, the comprehensive fuel consumption of the new Bora 1.6L is around 6.8 to 7.2, while the 1.4T model is around 6.6. Introduction to fuel consumption: Fuel consumption (Constant-Speed Fuel Economy): Constant-speed fuel consumption refers to the fuel economy indicator when a car is driving at a constant speed on a good road surface. Since constant-speed driving is a basic operating condition for cars on highways, and this type of fuel consumption is easy to measure, it is widely adopted. Comprehensive fuel consumption: Comprehensive fuel consumption is tested under different conditions such as urban roads, highways, and varying loads. It is only a reference, and the actual fuel consumption may be higher or lower than this number. For example, driving daily in busy city areas, frequently braking and accelerating, can lead to higher fuel consumption, even reaching 10 liters per 100 kilometers, which is quite normal.
1
1
Share

Which one is the low beam headlight on the Baojun 560?

The low beam headlight on the Baojun 560 is controlled by a lever on the left side of the steering wheel. Above the turn signal indicator, there is a symbol for the low beam headlight. Twist it twice to turn on the low beam. Introduction to low beam headlights: Low beam headlights are designed for close-range illumination. Their design requirements include a wide coverage angle (160 degrees) and a short illumination distance, with non-adjustable focus. Illumination range of low beam headlights: The low beam headlights illuminate approximately 30-40 meters ahead. According to experiments, when driving at 55 km/h at night, the braking distance after noticing an obstacle is exactly 30 meters. This means that if you spot an obstacle within the low beam's range and brake immediately, there will be no gap between the car and the obstacle. Of course, this is under ideal conditions with good vehicle and road conditions and a quick driver reaction. If the speed is higher, or if the vehicle or road conditions are poor, or the driver is fatigued with slower reactions, the outcome can be imagined. Therefore, it is essential to control your speed when driving at night. On flat, wide, and well-lit roads, you can use high beams and drive slightly faster. However, when encountering oncoming traffic, uneven roads, turns, bridges, narrow roads, or intersections, you should slow down, generally keeping the speed below 40 km/h.
10
0
Share

What is the chassis code of the new Fit?

2021 Fit is the fourth generation Fit, and the chassis code of this model is GR9. The chassis code is commonly known as the frame number, similar to a person's ID number. The frame number is the ID number of that car. Normal frame number locations: Except for trailers and motorcycles, on the door hinge pillar, door lock pillar, or one of the pillars connected to the door lock pillar, near the driver's seat; fixed on the left side of the dashboard; fixed on the inner side of the door, near the driver's seat. It should be in a place where it can be easily read without moving any parts of the vehicle except for the outer door. The VIN code of most domestic cars can be found on the left side of the dashboard or below the windshield. Importance of the frame number: The frame number is like a person's fingerprint. If the steel plate with the frame number is damaged, the owner must not cut the steel plate with the frame number by themselves. The damaged condition of the vehicle must be preserved, and the car should be driven directly to the vehicle management department for certification to prove that the steel plate with the frame number is indeed damaged. Then, the vehicle management department will handle the situation according to the actual circumstances.
16
2
Share

What is the fuel consumption per 100 kilometers for the Audi A7?

Audi A7 has an average fuel consumption of 14.45 liters per 100 kilometers. Introduction to fuel consumption: Constant-Speed Fuel Economy refers to the fuel efficiency indicator when a car is driving at a constant speed on a good road surface. Since constant-speed driving is a basic operating condition for cars on highways, and this type of fuel consumption is easy to measure, it is widely adopted. For example, France and Germany use the constant-speed fuel consumption at 90Km/h and 120Km/h as the main evaluation indicators for fuel economy. China also adopts this indicator. Fuel consumption testing: Special personnel select experimental roads, use a specially marked fuel tank to run a 100-kilometer round trip (acceleration fuel consumption can be calculated, but coasting is not allowed), and then divide by two to calculate the actual constant-speed fuel consumption per 100 kilometers.
5
0
Share

How often should the automatic transmission fluid be changed in a new Santana?

The automatic transmission fluid and filter in the new Santana should be replaced every 60,000 kilometers, or every two years or 50,000 kilometers, whichever comes first. Transmission fluid change interval calculation: The replacement cycle for transmission fluid is calculated the same way as the vehicle's maintenance cycle, based on either mileage or time in use. If the vehicle's manual clearly specifies both indicators, follow whichever comes first. If the manual doesn't provide such indicators or doesn't clearly mark the fluid change interval, replace it every 50,000 to 80,000 kilometers. Transmission fluid change methods: Circulating machine fluid change method: This method can completely clean out the old transmission fluid. However, it's relatively expensive and suitable for vehicles less than 5 years old.
7
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.