How to Remove the Rear Drive Shaft of a BMW X5?

1 Answers
MatteoFitz
07/30/25 3:21am
The method for removing and installing the rear drive shaft of a BMW X5: First, lift the vehicle. The rear drive shaft is located inside the left rear underbody guard panel, and special tools are required for removal and installation. The dimensions of the new BMW X5 are 4945mm in length, 2004mm in width, and 1791mm in height. The design features more angular lines, with a large-sized grille providing a strong visual impact and high recognition. The overall style continues the previous sporty feel while appearing more youthful visually. The use of lines makes this mid-to-large SUV look less bulky. In terms of power, the vehicle is equipped with a B58 3.0T inline six-cylinder turbocharged engine, delivering a maximum power of 340 horsepower and a maximum torque of 450 Nm.
Was this review help?
14
0
Share
More Forum Discussions

Which region does the license plate 'Qin' belong to?

Currently, there is no license plate with the designation 'Qin'. Points to note when installing a car license plate: 1. Installation position of the license plate: The front plate should be placed in the middle or on the right side of the front, and the rear plate should be placed in the middle or on the left side of the rear; 2. Installation requirements for the license plate: Special sealing devices for motor vehicle license plates must be used, with all seals complete and the plate securely installed; 3. Requirements for installing the plate holder: The inner edge of the license plate frame should be more than 5 millimeters away from the edge of the motor vehicle number characters. The steps for installing a car license plate are: 1. All fixed points where the license plate can be seen at the front and rear of the car need to be screwed with fixed screw components; 2. Once the license plate is in the appropriate position, tighten all the screws; 3. Align the cap with the pad and press it down to secure the cap in place.
16
4
Share

What to Do When the Dashboard Backlight of Maxus V80 Doesn't Light Up?

The solution for the dashboard backlight of Maxus V80 not lighting up is: you can turn on the car's small lights, press and hold the adjustment button on the left side of the dashboard, and adjust the brightness of the dashboard backlight according to your usage needs. If this doesn't work, you can visit a 4S shop for professional assistance. Taking the 2021 2.0T PLUS manual van short wheelbase medium roof 3-seater as an example, its length, width, and height are 4950 mm, 1998 mm, and 2345 mm respectively, with a wheelbase of 3100 mm. The body structure is a van, and the drive type is front-wheel drive. In terms of suspension, this model uses MacPherson independent suspension at the front and leaf spring non-independent suspension at the rear.
15
1
Share

Which Prado model features full-time four-wheel drive?

Taking the 2016 Prado 2.7L Automatic Luxury Edition as an example, this model is equipped with full-time four-wheel drive. Its dimensions are 4780mm in length, 1885mm in width, and 1845mm in height, with a wheelbase of 2790mm. The curb weight is 2145kg, featuring a 5-door 7-seat SUV body structure and front-engine four-wheel drive configuration. In terms of powertrain, it is equipped with a 2.7L naturally aspirated engine delivering maximum power of 120kW and peak torque of 246Nm. For suspension setup, this model employs double-wishbone independent suspension at the front and a four-link solid axle non-independent suspension at the rear.
7
3
Share

What is the remote start distance in meters?

2021 CR-V remote start distance is 10 meters. Remote start refers to starting the engine remotely via the key fob. The principle is quite simple: the vehicle starts the engine based on the signal received from the remote key. The remote start function has certain limitations for the vehicle itself, the most important being that it can only be installed in automatic transmission models. CR-V remote start operation method: First press the lock button, then hold the HOLD button. When the turn signals flash six times consecutively, it indicates that the engine has been successfully started remotely. The air conditioning will automatically turn on with internal circulation and adjust the cabin temperature based on the external temperature. A distance of 30 meters is no problem. Precautions for using CR-V remote start: When using it, note that the preheating time should not exceed the manufacturer's limit of ten minutes, and the number of starts should not exceed two. This is because the engine warms up much more slowly when idling in place compared to normal driving, and the three-way catalytic converter takes a long time to reach its operating temperature of above 350 degrees. During this time, the engine produces exhaust gases due to incomplete combustion, which places a significant burden on the three-way catalytic converter. Prolonged use under these conditions can damage the three-way catalytic converter.
16
1
Share

How to Remove the Cigarette Lighter in the Trumpchi GS8?

The method for removing the cigarette lighter in the Trumpchi GS8: 1. Remove the gear shift lever panel by prying it open with a flat-head screwdriver to detach the entire panel; 2. Unscrew the cigarette lighter panel by pressing open the panel door and using an M4 hex wrench to remove the two black screws; 3. Remove the entire cigarette lighter panel box by manually pulling out the plastic panel box of the cigarette lighter, then disconnect the connecting wires to complete the removal. The Trumpchi GS8 is a mid-size SUV with dimensions of 4740mm in length, 1910mm in width, and 1775mm in height, a wheelbase of 2720mm, and front-wheel drive. The Trumpchi GS8 is equipped with a 2.0-liter turbocharged engine across all models, delivering a maximum power of 185kW and a maximum torque of 390Nm.
17
4
Share

How to Remove Cement Stuck on a Car?

Cement stuck on a car can be removed by the following methods: If the cement has been on the car for less than 12 hours, first rinse the car body with clean water to maintain some moisture, then use car wash soap and a towel to repeatedly wipe the areas with cement until it is removed. If more than 12 hours have passed and the cement has fully hardened, you can purchase some acidic water from a pharmacy, dip a brush in it, and apply it to the areas with cement. Since cement is alkaline, the acidic water will gradually dissolve it. Afterward, rinse the area with clean water to completely remove the cement. Alternatively, you can use a specialized cement cleaner, which is highly effective for removing cement from cars. However, these cleaners can be corrosive to both skin and car paint, so the cleaning process should be quick to avoid skin contact and prevent the cleaner from staying on the car body for too long.
8
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.