How to Remove the Outer Taillight of BYD Tang 15?

[PeytonLee]

The method for removing the outer taillight of BYD Tang 15 is as follows: 1. The main taillights are located on both sides at the rear of the vehicle, with fastening screws inside the car; 2. Open the tailgate to find two plastic fastening clips inside, then remove them; 3. After removing the interior trim panel, the fastening screws inside will be visible—remove them directly; 4. When taking out the taillight, be careful not to damage the wiring harness, and properly store the old taillight. Taking the 2021 BYD Tang as an example, it is a mid-size SUV with the following dimensions: length 4870mm, width 1940mm, height 1720mm, wheelbase 2820mm, fuel tank capacity 68L, and curb weight 1895kg.

[LaEmma]

Removing the outer tail light of the BYD Tang 2015 model is something I've tried several times, and it's quite simple—the key is to have the right tools ready. First, park in a well-lit area, turn off the engine, and disconnect the negative battery terminal to prevent short circuits. A screwdriver or a small wrench will do the trick. Open the trunk door, and you'll find a plastic trim panel on the inner side where the tail light is located. Gently pry open the plastic clips to reveal several screw heads. After unscrewing them, the light cover will loosen. Carefully pull it outward, avoiding excessive force to prevent damaging the clips or scratching the body. When unplugging the power connector, squeeze both sides of the connector and pull it out slowly. The whole process takes just a few minutes, making it convenient to check for dust inside the light or replace bulbs if needed. However, it's advisable to wear gloves to avoid getting oil stains on your hands, and using clean tools prevents paint scratches. When reinstalling, align it properly to ensure the light cover is sealed tightly to prevent water leakage.

[GrahamLynn]

I was also a newbie when I first tried removing this taillight, and I felt a bit nervous, afraid of messing it up. Start by preparing some basic tools like a Phillips screwdriver and gloves, then check the car manual for screw locations—look for the plastic cover panel inside the trunk, just pry it open gently without worrying about damage. After unscrewing, the light housing will loosen; pull it out carefully without yanking too hard, or the plastic clips might snap. When unplugging the power connector, press the small button and pull it out slowly—don’t yank the wires. The whole process is pretty easy to learn, and making mistakes is normal—like when I overtightened the screws and scratched them, only to later realize a rubber wrench would’ve protected them. I recommend following a tutorial video; you’ll get the hang of it in one go. After finishing, test the light to make sure it works properly for peace of mind.

[OAshley]

Successfully replaced the outer taillight of the BYD Tang. A cross-head screwdriver and gloves are sufficient tools. Open the trunk door, locate and pry off the plastic cover panel inside to expose the screws. After removing them, the taillight housing can be taken out. Be steady when unplugging the power connector to avoid pulling on the wires. The steps are simple, so don't worry about complexity. Some car owners have used scissors as a substitute for a pry tool when lacking proper equipment, but be careful not to scratch the car's paint.

[DeCorey]

I find that removing the taillight isn't just for replacement purposes - I often do it for dust cleaning too. Just prepare a small screwdriver to open the interior trunk panel, unscrew a few bolts and the lens will slide out. Disconnecting the plug is quite straightforward. After completion, check if the bulbs are loose, and take the opportunity to wipe the socket clean to prevent poor contact. Doing this as part of regular maintenance saves a lot of hassle.

[EloiseLee]

When removing the outer taillight, pay attention to safety details, such as parking the car securely and disconnecting the battery to prevent electric shock. Wear gloves during operation to prevent cuts, and choose soft-tipped tools to avoid scratching the paint. After removing the screws, gently pull the light housing without using excessive force to prevent clips from breaking and causing water leakage. The entire process takes about ten minutes. If you're a beginner unsure about the light housing position, it's safer to check online diagrams for reference first.